Langer EMV-Technik GmbH
Langer EMV-Technik GmbH is a medium-sized electro-technical company which is active in the field of electromagnetic compatibility-related
- +1 888 687 5 687
+49 (0) 351 430093-0 - +49 (0) 351 430093-22
- mail@langer-emv.de
- sales@langer-emv.de
- Nöthnitzer Hang 31
Bannewitz, D-01728
Germany
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF2 set
-
The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can more precisely detect the interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
Micro probes 1 MHz up to 1 GHz
MFA 02 set
-
The two in the set included micro probes are used to measure low-frequency magnetic fields up to 1 GHz, e.g. at signal conductors (150µm), SMD componets (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the BT 706 Bias tee. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee to a spectrum analyzer or an oscilloscope. The MFA 02 set delivery of Langer EMV-Technik GmbH includes correction lines. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
Product
IC EMC Analysis
-
We carry out standard measurements according to BISS/IEC and analysis of the interference immunity and interference emissions of ICs during development.With the targeted EMC analysis, we uncover weak points in the ICs so that the IC developer can use them to develop improvements for the product
-
Product
Measuring and Calibration Stations
PCB
-
Is used to measure electric and magnetic fields of an ESD generator
-
Product
Scanner Probe
RFS set
-
The RFS set consits of three passive near field probes designed for the use in a measurement scanner during the development of E-field and magnetic field. They are designed for frequency ranges of 30 MHz to 3 GHz. The probe heads of the RFS set allow for close measurements needed to correctly localize interference sources on an electronic assembly.
-
Product
IC Measurement Technology
Emission
-
is used to measure conducted emissions (measurements with direct 1 Ohm/150 Ohm-coupling) according to IEC 61967-4 at IC pins.
-
Product
Accessory EFT/Burst generators IEC 61000-4-4
-
The field sources and the burst transformer are used to harden the device under test. They are powered by an EFT/burst generator.
-
Product
Measurement Technology for Teaching and Training
-
Is particulary suitable for training and further education. With the disturbance emission model, a variety of different experiments which improves one`s understanding of electromagnetic processes in modern electronic engineering are possible. The coupling mechanisms of disturbance emissions are visualized from their sources to the antenna. The impacts of EMC measures are then easier to understand.At VM 251 the electromagnetic d
