Meltronics Systemtech
Meltronics Systemtech is a product creation company. As a technology solution provider, we offer services and turnkey solutions in the harsh Real Time and Strategic Electronics Domain spanning many industries like avionics, medical, transport, defence & industrial equipments.
- (080)28525400/01/02
- meltronics@meltronicsgroup.com
- 82, 1st Main, 5th Cross, A Block
AECS Layout
Kundalahalli, Bangalore 560037
India
-
Product
PMC ARINC 717 Board
MS 1721
-
Bus Interface:- 32 Bit PCI Bus with PMC Interface. Speed of operation up to 66MHz. Spartan-3AN FPGA with ARINC 717 IP Core. One Channel ARINC 717 Transmitter and Receiver. Generates all PCM telemetry signals like NRZ, Bi-Phase, Differential Bi-phase, DM signals. Used to test all types of PCM based telemetry equipments. Configurable output signals format (parity, word length, Minor, Major frame, Bit position). User can configure the words and word positions in the frame. Driver interface for Windows2000/XP/VISTA and LINUX OS. Self Test future.
-
Product
Engine Simulator
MS 1118
-
Test Set-A calibration unit is a test jig is used to simulate parameters of Adour 804E and 811 engines of Jaguar aircrafts. It simulates current, voltage, speed, and turbine gas temperature. It performs NL Check, NH Check, TGT1 (Non T2 Compensated), TGT2 (T2 Compensated), Amp (Non T2 Compensated), Amp (T2 Compensated), Solenoid Volt, TGT Inject, NL Inject, and NL/TGT Redatum.
-
Product
ARM 9 System on Module
MS 1515
-
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
Product
Boiler Auxiliaries Plant Control Simulator
MS 1300
-
BAPCON SIMULATOR is used to test and validate Boiler Auxiliaries Plant Control Unit (Sigma BAPCON). It has CAN interface for simulating inputs and it is a microprocessor based system.
-
Product
Intel 186 EB & EC Processor Boards
MS 1503
-
- ATE- Data Acquisition System- Process Control- Industrial Automation
-
Product
RTM Analog Signal Conditioning Board
MS 3633I
-
CPCI Rear IO Analog Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on all type of Analog input and output interface including signal conditioning from ACIO board to Rear IO interface. Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
Gyro Evaluation & Test Equipment
MS 1113
-
The automatic test bench for gyros (ATP) is used to carry out the final acceptance test for the gyros in the stand-alone mode. It is a PC based test set up incorporating standard and custom built test and measuring instruments interfaced by GPIB bus. The gyros are installed on the platform, which is used to provide information pertaining to the angle at which aircraft is flying.
-
Product
CPCI Avionics Bus Card
-
Avionics Bus Card is high end ARM core based MILBUS Communication Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have MIL1553B, ARINC429, CCDL, digital I/O interface, USB, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board is based CPCI architecture and can be used with CPCI or PXI backplane. Rear IO Board is used to interface all IO’s of the board from Rear Side.
-
Product
Event Counter
MS 2022
-
Event counter is sleek system used to keep track of events. Event counter system is an independent unit with LED, event and reset buttons used for user interface. User generated events are displayed by LED (seven segment display scheme). Event counter Board consists of Microcontroller, counters, monostable multivibrator, transmitters & receivers (RX232, RX422). Event button is used to increment the events and reset button is used to reset the count value. Events are displayed on seven segment display mechanism for visual analysis. Event counter unit starts count from 000 and counts upto 999 events on pressing the event push button. The event value is transmitted over the RS232 / RS422 /TTL communication line to the recorder system.
-
Product
ISA DIO 96 Board
MS 1805
-
*Discrete Input / Output - 96 Channels*All Channels are compatible with 5V TTL / CMOS*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
High Speed Communication Board
MS 1712
-
- 12 Channel RS422 Standard Communication interface- 4 Channel Configurable Manchester Bi-Phase Signal communications- 4MBPS configurable baud rate- VIRTEX4 FPGA based design- Hardware Frame formation- Hardware Data validation with START & END frame identification and Checksum calculation for RS422 communication- 1MB DPRAM for PCI interface- Separate set of FIFO's for Transmit and Receive channel- 16 Channels data recording through CF (Compact Flash Storage - Capacity up to 8Gbyte) up to 30min @ 2Mb/sec- Online download through USB interface- Driver interface for Windows2000/XP/VISTA and LINUX OS- 6U size cPCI Board- Hot Swap facility is provided for the live Insertion and removing of the board- 12 RS422 channels in front panel interface using two 25-pin D-Type connector
-
Product
Weapon Control System Test Set
MS 1102
-
- Provides serviceability checks on armament system- Portable instrument- Check the Bomb release sequence, practice bomb release sequence, rocket release sequence, fuzing, and jettison of aircraft stores- Helps to identify faults of conventional armament- Microprocessor based design
-
Product
Air Data Computer (ADC) Tester
MS 1122
-
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
Product
ATE For ADC Module
MS 1527
-
The Semi-ATE is used for testing the analog ADC. It shall carry out the functional test on ADC analog module. The ATE shall have all necessary IO signals on the connector end. The semi-ATE can carry out the functional tests on ADC analog module with host PC or laptop. It provides +15V, -15V, +5V & -5V to module and +2.5V high precision reference voltage. It can able to control keysight N6700B Power supply mainframe using RS422 interface.
-
Product
Interface And Load Box
MS 3646I
-
Interface and Load Box is standard portable 19” rack mountable unit. It is customized unit for single channel tester of IFCC. This unit has cable/harness interface between CPCI System and IFCC LRU. This box also houses all actuator loads and switching circuits.
