Meltronics Systemtech
Meltronics Systemtech is a product creation company. As a technology solution provider, we offer services and turnkey solutions in the harsh Real Time and Strategic Electronics Domain spanning many industries like avionics, medical, transport, defence & industrial equipments.
- (080)28525400/01/02
- meltronics@meltronicsgroup.com
- 82, 1st Main, 5th Cross, A Block
AECS Layout
Kundalahalli, Bangalore 560037
India
-
Product
Boiler Auxiliaries Plant Control Simulator
MS 1300
-
BAPCON SIMULATOR is used to test and validate Boiler Auxiliaries Plant Control Unit (Sigma BAPCON). It has CAN interface for simulating inputs and it is a microprocessor based system.
-
Product
PCM Generator
MS 1607
-
The PCM Generator System used to generate different types of PCM format signals. The user can configure the PCM format to be generated. This system is an independent unit with LCD and Keypad for user interface. Primary application of the system lies in testing the airborne equipment.
-
Product
Combined Map Display Unit & Interface Unit Tester (COMED)
MS 1117
-
This system is used to test COMED (Combined Map Electronic Display) IFU cards. This ATE checks the LRU Status and card status and identify faulty component in the individual UUT. On fault, this suggests the possible component failure as diagnostic report, for repairing the cards.
-
Product
ECM PCB Tester
MS 1105
-
*Used for testing of DAWN RWR PCBs in Jaguar Aircraft*19” Rack mountable with built-in wide range of IO signals *Used in 4th line servicing of PCBs*Used in LRU and system level testing*Detects 100% fault coverage including track faults*Adaptability with off-the-shelf instruments
-
Product
Engine Simulator
MS 1118
-
Test Set-A calibration unit is a test jig is used to simulate parameters of Adour 804E and 811 engines of Jaguar aircrafts. It simulates current, voltage, speed, and turbine gas temperature. It performs NL Check, NH Check, TGT1 (Non T2 Compensated), TGT2 (T2 Compensated), Amp (Non T2 Compensated), Amp (T2 Compensated), Solenoid Volt, TGT Inject, NL Inject, and NL/TGT Redatum.
-
Product
PMC FPDP Board
MS 1741
-
- Four FPDP front panel outputs- FIFO buffering for real−time recording- FPDP Outputs: Two 80−pin FPDP connectors (A and B)- FPDP Outputs: Two 80−pin FPDP connectors(C and D)- Quantity: Standard: Two Front Panel Data Port (FPDP) connectors, each providing 32−bit output- Output Type: FPDP I, non−inverted configuration FPDP II, double the selected clock rate- Clock: On−board clock- FIFOs- Quantity: Four IDT72V3690 FIFOs, one for each FPDP port- Size: 32,768 x 36- Speed: FIFOs are capable of 166 MHz speed, but are run at one half of sample clock speed
-
Product
Universal Pylon Tester
MS 1121
-
Portable test equipment to check the electrical functionalities of pylons by simulating various store types in aircraft. This system is able to simulate the functionalities of different PIBs (IB/MB/CF, OB & Laser). The system provides facility to test two Pylons in parallel. The tester provides aircraft specific AC &DC voltages and facility to inject discrete inputs for checking output(s) viz firing voltages, fusing voltages. The system provides four channels of RS422 and Two channels of 1553B communication. Portable unit with caster wheels with all required hardware, power supplies, instruments, connectors and laptop housed in it.
-
Product
Board Test Adaptor (BTA)
MS 1104
-
BTA is used to test and validate TARANG (RWR) boards. The BTA has PC interface through RS232 / USB communication port. GUI based Test Software is used to test the UUTs and displays the result.
-
Product
Engine Speed Control and Measurement (Test Set A)
MS 1100
-
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
Product
CPCI Or PXI Analog IO Board
MS 1808
-
*Bus Interface*PCI Bus Interface, 6U Form Factor*Facility for Calibrating all Output channels*Hot Swap facility*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Airborne Video Delay Board
MS 2006
-
- Spartan FPGA based Design- Customized design for delaying & switching video inputs to RF section- Interface with EW Signal Processor Unit- Two channel video inputs and control- Video Signal Delay from 1ns to 1ms- Over duty Indications- Inhibit Control- Discrete Interface
-
Product
Centralized Warning Panel
MS 1116
-
The Centralized Warning Panel Test Rig is used for conducting Pre Installation Test of Airborne Centralized Warning display unit of Advanced Light Helicopter.
-
Product
Weapon Control System Test Set
MS 1102
-
- Provides serviceability checks on armament system- Portable instrument- Check the Bomb release sequence, practice bomb release sequence, rocket release sequence, fuzing, and jettison of aircraft stores- Helps to identify faults of conventional armament- Microprocessor based design
-
Product
Advanced ASCAN BIOMETER
MS 1526
-
Advanced ASCAN bio-meter is a versatile A-scan system for Biometry and IOL Power Computation. This system is used for finding eye axial length; cornea thickness and calculating the eye IOL power value. This system has capability of storing 1000 patient records and downloading facility. System will work as an ASCAN BIOMETER or ASCAN / PACHYMETER BIOMETER system. System consists of touch screen, color LCD, USB interface for downloading and thermal printer interface. It is an ARM9 micro controller-based system. This system uses ultrasound signal for measurements
-
Product
Communication and Differential IO Board
MS 1707
-
- Four RS232 PORTS with full handshake- 16 Differential Input Channels- 16 Differential Output Channels- Driver interface for Windows2000/XP/VISTA and LINUX OS
