Filter Results By:
Products
Applications
Manufacturers
-
product
Incremental > Heavy Duty Encoders - Hollow Shaft
Incremental > Heavy Duty Encoders - Hollow Shaft
-
product
Rotor Tester
SL Series
Shanghai Aoboor Electric Co., Ltd.
Applicable for testing fully opened, fully closed squirrl-cage rotors with process slot, with or without shaft, it can identify broken bars, slim bars, under-casting, porosity, sand holes, residues, improper end rings, internal short circut in bars, eccentricity.
-
product
Non-Contacting Single-turn
A rotary position sensor translates angular positions to an electrical signal. Rotary position sensors are designed for applications that typically require frequent adjustment. Shaftless designs allow for a different engagement mechanisms, such as a customized shaft, a motor control, a human interface adjustment or a mechanical arm position locator.
-
product
Rotating Torque Meter
NTS-6 series (S1/S2/S5/S10/S20)
Torque measurement of rotating body. Measure rotational torque during assembly of devices with rotating functions and on finished products. While the output shaft self-rotates, the built-in sensor catches load fluctuations on the rotating body. It is possible to measure the rotation starting torque of the rotating object ( which does not rotate by itself and does not have power) and the load torque during rotation. (Printers, copiers, zoom lenses, door knob mechanisms, hinge mechanisms, etc...)
-
product
EEXI Shaft Power System (SHaPoLi)
Datum Electronics Ltd has developed a shaft power limitation (SHaPoLi) EEXI Shaft Power System, providing the necessary features and functionality to comply with the MARPOL Annex VI, MEPC.335(76) EEXI regulations.Our system uses a Shaft Power Acquisition Module to constantly display, monitor and record propulsion shaft power to ensure compliance with the EEDI requirements relating to CO2 emissions for ships over 400 gross tonnage.
-
product
Load Measuring Pins
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
-
product
Tachometers
An instrument measuring the rotation speed of a shaft or disk, as in a motor or other machine.
-
product
2-28 Vrms Input, 2-115 Vrms Exc, 47 Hz - 1 kHz Freq
SDx
Synchros and Resolvers are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Resolver-to-Digital or a Synchro-to-Digital converter is used to convert these signals to a digital output corresponding to the shaft angle and/or velocity.
-
product
Shaft Measuring Gage with Dual Glass Linear Encoder
1100GX
The economical gaging system of the Model 1100-GX handles a wide variety of part lengths and configurations, resulting in fast, highly accurate measurements of cylindrical engine components. Whether it is needed for use in a lab setting or out on the shop floor, this rugged gage is adaptable to a wide variety of work environments. This versatile gage employs the latest technology in motion controls, signal processing and linear grating technology.
-
product
Torque Sensors & Torque Transducers
Datum Electronics is a world-leading designer, manufacturer and supplier of torque sensors, torque transducers & torque meters, bolt-on strain, weight & load sensors, as well as shaft power measurement solutions.With 30 years of expertise in torque and shaft power measurement, we research, design and manufacture our reliable & accurate torque sensors in-house. Besides, our team specialises in providing both industry standard off the shelf solutions, as well as bespoke custom torque sensors, built to your own specifications and requirements.
-
product
Transmissive Rotary Codewheel
HUBDISK-1
US Digital offers a wide variety of standard hub / disk assemblies (optical encoder disks attached to an aluminum hub) to aid with mounting on a shaft. Encoder disks may also be ordered as a stand alone item (see the Disks page). These rotary encoder disks are made from mylar polyester film. This material allows for a wide temperature range and is virtually unbreakable.
-
product
Magnetic-Inductive Testing
MAGNATEST® Product Family
Foerster Instruments, Incorporated
The MAGNATEST product family is used for the non-destructive testing of metallic materials for magnetic and/or electrical properties. The test instruments are used in the automotive and aviation sectors as well as in the production of semi-finished products. The focus is on testing components relevant to safety such as brake discs, or ball pins and functional components such as camshafts and drive shafts, pivots and piston pins. Typical test tasks include hardness checks, material differentiation and sorting. MAGNATEST can also be used for the automatic testing for the geometric properties of all metallic series components. The high-performance amplifier installed in MAGNATEST test instruments makes it possible to analyze harmonics, which guarantees an extremely reliable and precise repetition, even when impacted by perturbations.
-
product
General Purpose Probe
PIT-6
PIT-6 General Purpose Probe for Pressurized Systems - 6'' #304 stainless steel shaft. Diameter is 1/16''. Immersible. Maximum temperature 350°C, Time constant 0.5 Seconds. Shaft Terminated in a sub-miniature Type T Thermocouple plug. 10 foot Sub Miniature Type T extension lead supplied. Not isolated.
-
product
Sun Trackers
STR-series
EKO Sun Trackers are very compact, robust, relatively light weight and very power efficient. Inside the Sun Tracker a Harmonic Drive with advanced motion control unit is used on each output shaft. Harmonic drive is a leading drive technology for those application where high precision, durability, low backlash, high transmission ratios and torque is required. Due to its compact design and high transmission ratio small motors could be used to keep the power consumption low.
-
product
Micro-Surface Microprobe
ICT-4
ICT-4 Micro-Surface Microprobe - For use on integrated circuits and other micro specimens. 0.013'' diameter .5'' straight stainless steel shaft; slightly protruding sensor bead to facilitate temperature probing. 5'' tubular handle fits micro-manipulators. Maximum intermittent temperature 200°C, continuouse use 100°C, Time constant 0.025 Seconds. 5 foot lead. Not isolated.
-
product
Agriculture Solutions
The trend in agriculture: The drives of machines and commercial vehicles must be capable of transmitting increasingly high power within a limited space. Reproducible quality in series manufacture with the shortest possible production times are the key requirements in this industry.The hay makers and harvesters perform their task using straight bevel gears. Because the loads in these machines are comparatively small, a cost-effective manufacturing solution is crucial for the market success of straight bevel gears. It’s a different story as far as tractors are concerned: Spiral bevel gears are installed in the rear axles in this case – and the bevel gear set of a tractor’s rear-axle differential must transmit up to 400 kW. In tractors, cylindrical and planetary gears are also used in manual transmissions and counter shaft transmissions as well as planetary gear drives for transmitting power to the enormous drive wheels. These cylindrical and planetary gears must be efficient, quiet-running, and low-maintenance. With solutions from Klingelnberg, the entire portfolio can be produced on bevel-gear and cylindrical-gear machines.
-
product
Torsional Vibration Monitoring Systems
Advanced Telemetrics International
Are used for Noise Vibration and Harshness (NVH) testing and analysis in automotive drivetrain, wind turbine gearbox and various other applications where measuring or monitoring rotating vibration is important. These systems are used to transmit torsional acceleration from a rotating shaft or component, while the machinery is running.
-
product
Inductive Motor Control
The inductive motor control position sensor family detects the electrical position within one pole-pair of a rotating shaft and can be used for the motor commutation of a brush-less DC (BLDC) motor. Based on the inductive sensor technology, this family measures the coupling between an excitation coil (TX) and two receiver coils (RX) via a rotating target. The coils are executed as printed circuit coils and the rotating target is a simple punched metal part. With the correct layout of the coils and the target, both synchronized to the number of pole-pair count of the motor, the IC output is proportional to the electrical angular position within one pole-pair segment with increased resolution and high performance of only 0.3° electrical INL!
-
product
Rectal Probe For Rats (Isolated)
RET-2 ISO
• An isolated sensor (can be used with monitoring equipment where electrical interference from other electrodes may be present).• Reinforced strain relief for applications where probe is in more frequent use.• Smooth ball tip. Stainless steel shaft - '' long, .059'' diameter. Tip diameter .125'', 5 foot lead length. Time constant 0.8 seconds.
-
product
Rotary Encoders
Our proven rotary encoder and resolver solutions are used worldwide in a variety of industries such as Medical, Oil & Gas, Aerospace, Packaging, Robotics, Paper and Steel, to name a few. Dynapar''''s vast product portfolio offers a wide selection of incremental and absolute encoders engineered with cutting edge optical or magnetic technology, brushed and frameless resolvers, and accessories. Dynapar offers a wide variety of optical or magnetic shaft encoders and resolvers, as well as any resolver or encoder product your particular application may require.
-
product
Hand-held Tachometers
SHIMPO offers a wide range of hand-held tachometers that measure the total number of revolutions of a shaft or number of pulses of reciprocating equipment. Our models can measure and record last/min/max and up to 10 reading using up to 16 different units of measure. Our tachometers are designed for applications such as Motor Speed/Conveyor Speed/Fan Speed/Length Measurements that measure rpm of motors or shafts, either contact or non-contact with Laser style combination tachometer.
-
product
Inductively Powered Telemetry Systems
Advanced Telemetrics International
ATi Inductively Powered Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary receiver.
-
product
Twist Testing
STT
The STT Shaft Twist Tester is a system designed for quickly testing of twist structures and/or twist-freed condition on shafts in seconds.
-
product
Oral Probe
OT-1
The OT-1 oral temperature prove for humans is re-useable and has a fast response time.• Fast reading oral use, with accuracy to 0.1°C .• Smooth ball tip. Stainless steel shaft - 3'' long, .050'' diameter. Tip diameter 1/8'', 5 foot lead length. Time constant 0.8 seconds.
-
product
General Purpose Probe
BT-1
BT-1 General Purpose Probe - Probably our best general purpose probe designed for temperature measurement of solids, liquids, gases and semi-solids. Welded stainless-stell shaft, plastic handle. Tip is .028'' diameter bent at right angle to probe to facilitate accurate surface measurements. Immersible. Maximum temperature 240°C, Time constant 0.15 Seconds. 5 foot lead. Not isolated.
-
-
product
Open Optical Encoders
An optical encoder is an electromechanical device which produces an electrical signal output proportional to the linear displacement of a linear guide or the angular position of an input shaft.Open encoders are exposed and feature no external integrated enclosure. The advantages of open optical encoders include the effective elimination of backlash, shaft wind-up (torsion) and other mechanical hysteresis errors.A rotary open optical encoder consists of a position measurement readhead and an accurate rotary scale marked either on the periphery of a ring or on the face of a disc.The readhead measures position by optically sensing the regularly-spaced scale markings and outputs this information as an analogue or digital signal.The signal is subsequently converted into a position reading by a digital readout (DRO) or motion controller.
-
product
Miniature Absolute Magnetic Shaft Encoder
MA3
The MA3 is a miniature rotary absolute shaft encoder that reports the shaft position over 360 with no stops or gaps. The MA3 is available with an analog or a pulse width modulated (PWM) digital output.
-
product
Dynamic Torque Sensing System
Advanced Telemetrics International
Are utilized in applications where conventional rotary torque transducers are not practical due to excessive shaft speeds, vibration, and dirty, oily environments.
-
product
Tachometers
Is an instrument measuring the rotation speed of a shaft or disk, as in a motor or other machine. The device usually displays the revolutions per minute (RPM) on a calibrated analogue dial, but digital displays are increasingly common.
