Filter Results By:
Products
Applications
Manufacturers
Receptacles
receive conductors.
-
product
Voltage Testers
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
-
product
Extender
3690-3
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
MEASUREMENT QUALITY JUMPERS
4000-1065
This kit includes two (2) Singlemode Enhanced MQJs (ST-to-Socket, 1 meter, SinglemodeEnhanced), two (2) Singlemode Enhanced MQJs (ST-to-Pin, 1 meter, SinglemodeEnhanced), two (2) Multimode MQJs (ST-to-Socket, 1 meter, Multimode), two (2)Multimode MQJs (ST-to-Pin, 1 meter, Multimode), two Snap Lock Plugs, and two SnapLock Receptacles.
-
product
Extender
3690-2
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
DER-075 Double-Ended Receptacle
DER-075
Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 130Recommended Travel (mm): 3.30Overall Length (mil): 1,710Overall Length (mm): 43.43Rec. Mounting Hole Size (mil): 53Rec. Mounting Hole Size (mm): 1.35Rec. Mounting Hole Remark: 53 to 55 mil / 1.35 to 1.40 mmRecommended Drill Size: #54 or 1.40 mm
-
product
Electrician & Technician Testers
EVSE's Electrician and Technician testers are created for installation professionals, and are small and durableenough to be carried in a toolbox. These weatherproof handheld units allow new chargers to be checked after installation, verifying a number of vital power and safety requirements, as they simulate the connection a charger makes with an electric vehicle. Simply plug the charger's J1772 connector into the tester's receptacle and you are ready to evaluate operation.
-
product
GFCI & Receptacle Tester
GFCI & Receptacle Tester - GFCI & Receptacle Tester for electrical work.
-
product
110-125V Receptacle Tester
1938
Peaceful Thriving Enterprise Co Ltd
Test for 110-125V AC circuits. Detect faulty wiring in 3 wire receptacle.
-
product
Super-Safeway Receptacle Tension Tester
1301270007
Super-Safeway Receptacle Tension Tester & Receptacle Tension Tester in Carrying Case
-
product
Electrical Receptacle Tester
ERT100
UEi Test & Measurement Instruments
The ERT100 is a rugged, well-designed and well-built electrical receptacle tester. Featuring 6 different results with indicator lights for outlet condition, making it easy to read. With over molding and a comfortable grip, it fits comfortably into your hand. And is backed by a 1-Year limited warranty.
-
product
Host emulator
E84
Precision Development Consulting Inc
A USB controlled and self-powered emulator for functional testing SEMI E84 implementations. (E84-1000) This was developed because there was nothing like it in the marketplace, and it was clearly needed. This product enables a factory automation engineer to perform E84 functional testing anywhere in the world. Weighing less than 5oz, it is neither a burden, nor a power hog. You will never need to look for an additional power receptacle in the fab. The emulator gives the user full control over the sequence so that any test can be performed. Existing products were large and unwieldy, and provided canned tests that could not be modified to meet the requirements that Fab managers impose on their suppliers.
-
product
Receptacle Tester
RT500
Designed to detect the most common wiring problems in standard 120V receptacles.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.Made in USA of U.S. and imported parts.
-
product
110-125V AC Receptacle Tester
1933
Peaceful Thriving Enterprise Co Ltd
Test for 110-125V AC circuits.Detect faulty wiring in 3 wire receptacle.
-
product
12-600V AC Adjustable Non-Contact Wire Tracer
5220
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from 12V~600V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
-
product
DER-100 Double-Ended Receptacle
DER-100
Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 130Recommended Travel (mm): 3.30Overall Length (mil): 1,710Overall Length (mm): 43.43Rec. Mounting Hole Size (mil): 67Rec. Mounting Hole Size (mm): 1.71Rec. Mounting Hole Remark: 67 to 69 mil / 1.70 to 1.75 mmRecommended Drill Size: #51 or 1.75 mm
-
product
80-1000V AC Non-Contact Voltage Tester
5226
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from 80V~1000V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
product
Extender
3690
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle
KR100
K100 Series, Pitch 100mil, Receptacle, no wire wrap pin. Brass with gold finish.
-
product
Variable Power Supply
VS3
The VS-3 power supply is a very convenient portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 3 amps, thus the name VS-3. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-3 is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case. A unique feature of the VS-3 is that it contains “Magnet Packs” on the back of the case. These “Magnet Packs” can support the VS-3 and allow it to “hang” from any magnetic metal surface. The VS-3 can be powered by our UPS system, eliminating the need for an extension cord. The ability to magnetically attach the VS-3 near the source of connection and eliminating the need for an extension cord makes the VS-3 a “must have tool” for technicians.
-
product
GFCI Receptacle Tester
RT600
Designed to detect the most common wiring problems in standard 120V receptacles.Also tests GFCI receptacles for proper operation.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.
-
product
12-1000V AC Adjustable Non-Contact Voltage Tester
5220A
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from12V~1000V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
product
Electrical Testers
Regardless of what your trade requires, Klein Tools has an electrical tester for the job. With non-contact testers as well as outlet and receptacle testers, there’s guaranteed to be the tool for your jobsite needs. All Klein’s testers are engineered for ease of use and to stand up to the tough jobsite conditions encountered by professionals every day.
-
product
Rugged Rectangular Fiber Connectors
TE Connectivity (TE) has a range of rectangular fiber connectors for rugged environments including the ARINC and MTCT connectors. Whether you are designing collision avoidance systems, in-flight entertainment, or air-to-ground communications, you face a challenging economic environment and an ever-increasing demand for weight reduction. TE's ARINC 600 next generation receptacle connector allows you to reduce both weight and costs. TE's MTCT connector is a compact, lightweight design connector for use with ARINC 801 fiber optic termini. Ideal for applications such as avionics, in-flight entertainment systems, communications, production breaks and other areas.
-
product
HDMI
SCHILLER AUTOMATION GmbH & Co. KG
HDMI test adapters and test fixture kits facilitate Source and Sink compliance testing and HDMI cable testing. Our products are used in Certification Testing to CEA 1.3b, 1.4a, 2.0 and 2.1 standards. 1080p and 4K formats are supported. We offer A and D style plug and receptacle connectors, male and female SMA leads, with and without HEAC channels.
-
product
Receptacle Tester w/GFCI
61-501
*Warns against faulty wiring in 3-wire receptacles*For use on 120VAC circuits*1-year warranty
-
product
180V-260V AC Socket Tester With RCD Test (For UK)
1943
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 180~260VAC circuit.*LED indicators & Digital display.*30mA leakage current measurement.*RCD Test.I*t can perform self test after plug-in ( Voltage sould be above 180V ).*Detect faulty wiring status in 3 wire receptacle.*This socket tester will give LED indication as well if the main voltage is below 200V or above 260V.*Earth loop impedance test.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 11W*Frequency: 50Hz
-
product
Hand Insertion Tools
Zierick Manufacturing Corporation
Ideal for low volume, short run and prototype PCB assembly applications, Zierick’s hand tools offer a simple and reliable method for inserting press fit and splay mounted terminals. The hand tool can be easily installed on any type of press machine for increased flexibility and faster insertion. With the addition of a lower tool die, terminals can then be splayed and locked into place to improve reliability and prevent part removal and rotation. Zierick hand tools are available for PCB-mounted quick-disconnect terminals, quick-disconnect receptacles, post receptacles, test points and IDC terminals. Simple and reliable method for inserting press-fit and splay mounted terminals. Single tool can handle multiple terminal insertion applications. Tools can be installed on almost any type of manual or pneumatic press. Please click here for a PDF user manual for Zierick's hand tools.
-
product
Quick Access Recorders
QAR
Two QAR styles are available depending on the features needed, both include our specialized Silo™ Quick Access Recorder Software. Silo QAR with webFB hardware is the ideal certified solution for programs on Boeing 737 aircraft. It quickly attaches to the Flight Data Recorder (FDR) test receptacle and gathers data using the ARINC 717 protocol. For applications on other aircraft or using other protocols, Silo QAR with webCS hardware includes ARINC 429 and Discrete interfaces in addition to ARINC 717.
-
product
Battery Monitor
BAF-M2
Schumacher Electric Corporation
BATTERY MONITOR• Plugs into a 12 volt automotive cigarette lighter receptacle• Allows instant monitoring of battery & charging system voltage• Constant automotive battery and charging system check with a digital readout• LED warning lights alert you when your battery or charging system is not functioning properly• Detects charging input voltage within 0.1 volts variance• Detects problems with the alternator, diode and any variance of more than 0.8 volts• Alerts you once battery drops to 12.0 volts giving you approximately one more hour of run time, depending on the system’s wattage• Digital display indicates electrical voltage of your battery• Mounted display on your car’s dashboard for constant monitoring of your electrical system Contents: (1) Battery Monitor with 12V DC plug
