Filter Results By:
Products
Applications
Manufacturers
Interconnects
Links between systems, networks,nodes, equipment, devices, components and circuits.
See Also: Mass Interconnect, Connectors, Cable Assemblies, Interfaces
-
product
High density PCB connectors
MHD/MDD/MDP Series
Smiths Interconnect's MHD/MDD/MDP series is an ESA qualified, high density board to board and board to wire interconnect available in up to 400 positions, with available insulators to accommodate coax and power contacts.
-
-
product
Calibration & Demag.
Model 990A/990C
The Model 990 Series Magnetreaters® are highly accurate, pulse type, ringing demagnetizers (also called treaters) for the controlled stabilization of permanent magnets and permanent magnet assemblies. Regardless of line voltage stability, they provide a controlled output through continuous pulse amplitude regulation. Treating voltage is variable from 0 to 600 VDC. Additional energy can be added to the Model 990 Series by interconnecting a Model 992 Energy Booster. The energy level is increased from 18 to 36 watt-seconds. With this option, treating coils will produce higher demagnetizing fields and lower ringing frequencies, which can provide greater field penetration in some applications.
-
product
PMC to PCI Adapters
The PMC to PCI, PMC to CPCI and PMC to PC/104+ adapters enable the use of the PMC650 or PMC850 bus analyzers in PCI, CompactPCI and PC/104+ systems. The PMC analyzer plugs onto the adapter and then the mated adapter and analyzer plug into a PCI, CompactPCI or PC/104+ system. These passive adapters route the bus signals from the analyzer to the bus with minimal trace length and impedance matching. The adapters provide the full 64 bit interconnect between the analyzer and the bus.
-
product
Eurocard Plugbord
4614
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. 3-Hole Solder Pad Pattern on both sides. 3-Hole Solder Pads ( 0.28” x 0.080” ) for interconnecting multiple component leads. Interleaved buses on both sides, back-to-backPad and bus surfaces solder-coated for user convenience, Green Solder MaskRow and column legends provided
-
product
PCI Adapter for cPCI
PCI2cPCI-32
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
product
High Power Rack And Panel Connectors
LSH Series
The LSH rack and panel connectors include leading-edge Hypertac® hyperboloid technology. The Polyphenylene sulfide (PPS) insulators interconnect technology ensures LSH connectors are easy mating. The LSH Series delivers customers a high life cycle.
-
product
Phase Sequence Indicator
8PK-ST850
Two functions in one unit incluidng open phase and phase sequence. Large size alligator clips : able to clip on switch-board terminals easily. Identify 3 phase sequence and open phase check Ideal for installing conveyor lines, pump systems and interconnected drivers. No exposed metal parts. Safety features are incorporated throughout, including the pushbutton switch designed to minimize damage due to negligence. Safety approval: CE marks, IEN 1010 CAT. II.
-
product
CompactPCI
CompactPCI is a computer bus interconnect for industrial computers, combining a Eurocard-type connector and PCI signaling and protocols. Boards are available in 3U or 6U sizes
-
product
RF Filters
Smiths Interconnect is committed to providing technically advanced, high quality “state-of-the-art” RF Filters, Multiplexers, Switched Filter Banks, and Integrated assemblies, from 100 KHz to 65 GHz. All products are subject to the same rigorous design, manufacturing, and inspection criteria. Regardless of the application, our internal process and procedures help ensure that all products are fully compliant to all specifications. Our R & D activities are constantly evaluating new materials, plating techniques, and manufacturing processes to offer the highest performing components available today.
-
product
Elastomeric Contact
High performance contact materials specially designed for the advanced needs of the electronic industry. PariPoser Interconnects makes electrical connections uniformly between opposing contact areas using conductive columns, which are regularly distributed within a sheet of advanced polymer. PariPoser Interconnects is custom formulated depending on the application’s design rules.
-
product
PXI 16 x SPDT Reed Relays
40-110-021
The 40-110/115 range of switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. General purpose reed relays are used for the construction of small switching networks or for slaving up to larger switches.To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
product
JTAG Test Software
JTAG Technologies software has been subject to a program of continuous development for over 20 years. The first products, launched in 1991 formed the start of our 'Classic' range of software and featured the first automatic boundary-scan test program generator (ATPG) for PCB interconnects plus associated test execution and diagnostics software. In 2006 JTAG Technologies launched it's new flagship tools platform JTAG ProVision.
-
product
OBD Development Kit
The OBD Development Kit is a modular development system designed to speed up the development of devices that interface with the OBD bus. It consists of the Interconnect Board, three removable modules (Power, OBD Drivers, and STN OBD IC), and an OBD cable.
-
product
Heavy Duty Modular Connector
HyperMod Series
Smiths Interconnects’ heavy duty, modular, rectangular HyperMod Series is available with a variety of contacts, special shells for harsh environments and special high creepage/clearance modules. The series conforms to DIN 43652 standards and is NF F61-030 railways approved.
-
product
Module Solution
G2 - 2
The G2 offers the reliability of VPC interconnect technology in a compact, high-density two-module package. While simultaneously engaging a wide range of interconnect options in multiple configurations, the G2 provides a rapid alternative to repeated connect and disconnect of individual leads and connectors in a rugged, reliable system.
-
product
Lightwave Mainframes
The Keysight Technologies Lightwave solution platform addresses different measurement needs for passive and active Lightwave components. The platform is the key component to combining the Keysight Lightwave modules and their interconnection by providing features like clocking and triggering and the required software control for test solutions.
-
product
PXI 24 x DPST Reed Relays
40-115-122
Available in normally open (DPST & SPST) configurations. Connections are made via a front panel micro-D 96-pin male connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120 and 40-125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, slaving up to larger switches or operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board easing the construction of complicated wiring.
-
product
Software
D2B
The unique capabilities of Teradyne's D2B software enable EMS and OEM manufacturers and partners to interconnect their global enterprises to optimize printed circuit board assembly test and inspection efficiencies early in the manufacturing / build cycle. D2B is a powerful suite of solutions that provides a standards-based architecture that supports GenCAM and ODB++ file formats enabling electronic manufacturers to outperform their competition, maximize profitability, and get to market first.
-
product
Solid State Voltage Injector
J2110A
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
product
USB 4-port Hub For Elan's USB T&M Instruments
USBMicroHub4
The MicroHub4 has connections for 4 USB2.0 measurement tools, and uses only one host USB port. Elan's test and measurement products can be interconnected to allow them to operate in synchronised mode, or left non-connected for distinct operation.
-
product
RF COMPONENTS
If space is an issue and you are looking for high quality RF Components, ETL's wide range is designed and manufactured at the ETL factory. Covering DC to 40GHz, these are at the heart of many of our 19" Rack Systems.A key feature of many of ETL components is the ability to pass or block a 10 MHz signal or DC voltage through the products, which can be used to power interconnecting components or pass a stable frequency reference to a LNB or BUC within the system.
-
product
DIN Contacts
Rugged DIN style contacts and connectors that are capable of supporting wide bandwidth applications. All fiber optic contacts are offered fully terminated and tested to ensure integrity for rugged environments. Smiths Interconnect also offers a complete line of fiber optic connectors to terminate to the other end of the cables. These include ruggedized single channel (RSC), FC, ST, LC Duplex/Simplex, MTP, MT-RJ and Ruggedized SC connectors. Please consult factory for cabling options.
-
product
Socket Accessories (Thru-Hole Options)
The male pin adapter consists of standard high temperature FR4 with pressed in terminal pins and threaded inserts for mounting the socket. The top side of adapter has gold plated pads to receive socket interconnect and the bottom side has 0.006″ to 0.018″ diameter pin tails. These pins can be soldered to the plated thru holes in the target board. Then socket can be mounted to the threaded insert.
-
product
Probe Positioners (Probe Manipulators)
PacketMicro offers a broad ranges of probe positioners to allow designers to guide standard oscilloscope/TDR/RF/microwave probes onto the small geometries of fine-pitch interconnects, SMD packages, MCMs, hybrids and ICs.
-
product
Vigilant Aircraft Hygrometer
137
The Edgetech Instruments Model 137 Vigilant Aircraft Hygrometer is a rugged, shock mounted military qualified instrument used for the primary measurement of dew point in flight or in installations with existing flow, such as wind tunnels.It features a miniature remote dew point sensor employing a platinum resistance thermometer, and has 15 feet of interconnecting cable to the control unit. Precision calibration units for the linear analog outputs are included.
-
product
Turn-key ATE Interface Boards
We offer services for modeling and simulation and complement that work with measurement and validation of those models, at your desired frequency and your required fidelity specifications. Our design and programming expertise includes: Teradyne Catalyst through Integra FLEX; Advantest 3340 through T2000; Verigy 82000 through 93000. turn-key solution for ATE interface boards, we understand the limits of the interconnect technology (laminate, conductors and via’s, connectors and sockets) and use that understanding to guide our principles of design.
-
product
FlexVPX Backplane
FlexVPX provides system designers with the flexibility and performance required for the most demanding applications. The ability to interconnect 2 and 3-slot 3U VPX compliant backplanes allows for custom system configurations using COTS hardware. Backplanes are equipped with PCI Express bridges that ensure fast and high-throughput for point-to-point communication between different elements in the system.
-
product
Multi-Mode And Single-Mode Applications
Expanded Beam Size 5 and 12 Contacts
Expanded Beam Fiber Optic Contact technology is specifically designed to fit into standard size 12 cavities of MIL-DTL-38999 Series I, III and IV connectors. The size 12 contact provides a robust fiber optic interconnection with low susceptibility to contamination and fits a variety of cable types with diameters from 1.6 to 2.2 mm with additional versions available upon request. The contacts are rear release/rear removable with standard size 12 removal tool.
-
product
Bulk Cables & Connectors
Interconnect equipment in AV systems to accommodate different applications.
