Pull Force
strength necessary to extract.
See Also: Force, Compression, Crimp Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
Product
Grips and Fixtures for Force Gauges
-
AMETEK Sensors, Test & Calibration
We supply a range of grips and fixtures for the Chatillon force gauges. Below you will find a selection of our most popular grips and fixtures. If you cannot find what you are looking for, please contact us for a presentation of our full range.
-
Product
3-Component Quartz Force Rings
260 Series
-
Three-component quartz force ring sensors are capable of simultaneously measuring dynamic force in three orthogonal directions (X, Y, and Z). They contain three sets of quartz plates that are stacked in a preloaded arrangement. Each set responds to the vector component of an applied force acting along its sensitive axis. 3-component ring force sensors must be statically preloaded for optimum performance. Preloading provides the sensing elements with the compressive loading required to allow the proper transmission of shear forces. Versions are available with ranges up to 10k lb (45k N) in the z-axis (perpendicular to the top surface), and up to 4000 lb (18k N) in the x-and y (shear) axes. Both ICP® and charge output styles are available.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type D, Ø0.80mm, 305gf
K100-D080305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style D, Tip Diameter Ø0.80mm, Spring force 305gf, Steel with Gold Plating.
-
Product
ThermalAir Series Temperature Forcing System
ThermalAir TA-1000B Rack Mount Test System
-
The ThermalAir TA-1000B high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -25°C to +200°C.
-
Product
Force Measurement
-
Using state-of-the-art technology, ABB provides purpose built solutions for your force and dimension measurement needs, making it possible for your production output to accurately match the most varying and demanding requirements.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type Q, Ø0.80mm, 230gf
K100-Q080230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style Q, Tip Diameter Ø0.80mm, Spring force 230gf, Steel with Gold Plating.
-
Product
PXI Module Adapter, Pull Thru Adapter, Receiver, 1 Position
510109462
Adapter Module
PXI Module Adapter, Pull Thru Adapter, Receiver, 1 Position.
-
Product
Force Tensiometer
K6
-
Our Force Tensiometer – K6 is a robust and reliable manual instrument for measuring surface tension and interfacial tension using the ring method. As a quality product from our precision mechanical workshop, it produces fast, easy and accurate measurements for surfactant solutions and solvents.
-
Product
Bond Force Measurement And Calibration Systems
BFS-20
-
Based on its design and easy handling it can be used also on other brands to measure the bond force.
-
Product
Force Measurement
-
Imada offers a complete selection of force measurement tools including force gauges, test stands and attachments. The gauges can be used by hand or combined into customized force measurement systems capable of addressing a wide variety of applications and budgets.
-
Product
Atomic Force Microscopy
-
Bruker’s industry-leading AFM microscopes provide the highest levels of performance, flexibility and productivity, and incorporate the very latest advances in atomic force microscopy techniques. Applications range from materials science to biology, from semiconductors to data storage devices, from polymers to optics with measurement of nanoscale topography, nano-mechanical, nano-electrical and nanoscale chemical mapping.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 305gf
K100-H080305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
-
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type Q, Ø0.80mm, 155gf
K100-Q080155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style Q, Tip Diameter Ø0.80mm, Spring force 155gf, Steel with Gold Plating.
-
Product
48 Ω HMM Pulse Force Probe
PHD-HMM-48-1
-
High Power Pulse Instruments GmbH
*High current wafer-level and package-level 98 Ω HMM probing with grounded DUT*Built-in high surge 48 Ω pulse reflection suppression resistor up to 80 A peak*Fast rise time < 0.5 ns due to low inductance GND loop*Variable pitch from 50 µm to 5 mm*Tungsten replacement probe tips*SMA pulse force pigtail*Compatible to PHD-3001A interface*High reliability
-
Product
Cable Pulling Analysis
CABLE
-
CABLE quickly solves complex three-dimensional cable pulling tension and sidewall pressure calculations, allowing you to make rapid and accurate design decisions.Don't leave installation to chance.
-
Product
ZIF (Zero-Insertion-Force) Socket
Series 516
-
Zero Insertion Force Socket. A choice of 24, 28, or 40 pin count devices can be inserted without bending or otherwise damaging the legs, since no force is required to either insert or remove the component from the socket. Contacts are normally open and are closed by a unique cam action controlled by dual lever arms. The last 15° of movement of the cam provides a wiping action to the contacts on the legs of the device to remove any residue, ensuring a gas-tight seal.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type L, Ø1.50mm, 230gf
K100-L150230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style L, Tip Diameter Ø1.50mm, Spring force 230gf, Steel with Gold Plating.
-
Product
Miniature Quartz Force Sensors
-
Often the test engineer will try to take low level measurements with a sensors not rated for these low levels. Due to insufficient sensitivity the resulting data may be noisy, hard to analyze or unusable. Using the appropriately sized and ranged PCB Miniature Quartz Force Sensor solves the problem and gives reliable data at a Low Amplitude level. The miniature sensor configuration permits low-amplitude, dynamic compression, tension, and impact force measurements.
-
Product
Conductivity Type (P/N) Checker By Contact Thermo-electromotive Force Method (seebek Effect)
PN-12α
-
*Thermo electrode and cold electrode is mounted detecting part of measuring probes*Possible to check most figure of sample such as single crystalline silicon wafer, bulk, ingot and so on*Please select from 2 types;1) 2 probe ver.(Hot probe, Cold probe),2) 1 probe ver.(Hot & Cold probe)
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type D, Ø0.80mm, 155gf
K100-D080155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style D, Tip Diameter Ø0.80mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Scanning Probe Microscopy/Atomic Force Microscopy (SPM/AFM Analysis)
-
Rocky Mountain Laboratories, Inc.
Scanning probe microscopy (SPM) refers to a family of measurement techniques that utilize a scanning probe. The most common measurement is Atomic Force Microscopy (AFM Analysis), which measures surface topography. Imaged areas can be from the nm scale to as large as 100 µm X 100 µm. Heights and depths of features can be measuredand many surface roughness parameters, e.g Ra, can be calculated. 3-D images can also be produced for dramatic data presentation. Magnetic and electrical response can also be measured with SPM.
-
Product
Ergonomic Force Gauges
-
The ergonomic gauges from Chatillon are ideal for functional capacity evaluations and basic muscle strength measurements where economy and ease-of-use are essential. Simplicity is a key design criterion for these ergonomic gauges. They are an excellent, low cost solution for tensile or compression testing.
-
-
Product
Benchtop Thermal Forcing System
-
Wewon Environmental Chambers Co, Ltd.
Benchtop thermal forcing system from Wewon Environmental Chambers Co., Ltd. has a mini body structure and affordable machine price. The machine can test a wide temperature range, Since no compressor is required for refrigeration, so the benchtop temperature forcing unit’s energy consumption is very low. The repeated resistance degree of the tested sample in the instantaneous extremely high temperature and extremely low temperature continuous environment can detect the chemical changes and physical damage caused by thermal expansion and cold contraction of the sample in the shortest time, so as to achieve the goal of confirming the quality of the tested sample.https://www.wewontech.com/benchtop-thermal-forcing-system/
-
Product
Load Pull Test Fixtures
-
Low Insertion Loss for High VSWR TuningMultiple Connector Configurations50Ω and Transformers (Klopfenstein, Quarter-wave) AvailableHeatsinks and Fans AvailableCooling (Water cooling, Forced air cooling) AvailableIntegrated Biasing Available
