Compression
the result of being pressed.
See Also: Force, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic, Crush, Extensometers, Bending
-
Product
Non-Contacting Video Extensometer
AVE3
-
The AVE3 is Instron’s most advanced extensometer, engineered for high-precision, non-contact strain measurement across a wide range of mechanical tests—including tension, compression, and flexure. Its adaptable design accommodates various specimen types, sizes, and elongation ranges, making it ideal for everything from delicate films to robust metals. By eliminating the need for clip-on devices, the AVE3 streamlines setup and ensures uninterrupted data collection through specimen failure, even in high-energy break scenarios, such as composites. Compatible with environmental chambers and fluid baths, it supports non-ambient testing with ease. With compliance to ISO 9513 and ASTM E83 and a fast 500 Hz data rate, the AVE3 delivers reliable performance for demanding testing standards.
-
Product
Frequency Expansion Modules
-
bsw TestSystems & Consulting AG
Up To 1.5THz For Network Analyzers Modern communication standards, like for instance 5G, place high demands on components (mixers, amplifiers, antennas, etc.), which have to be examined in high frequency bands (millimeter waves); the requirements include: broad frequency coverage, sufficient output power to operate the components under compression, high dynamic range and stability as well as a reduced dynamic content within the spectrum.
-
Product
Logic Analyzer
LAP-C(16064)
-
Zeroplus Technology Corperation
Bandwidth:75MHzWorking Range: -6V~+6VAccuracy: ±0.1V, Memory:1MbitsDepth(Per Channel):64Kbits (Max 16Mbits for compression)
-
Product
Gain-Compression Measurements
S95086B
-
The S95086B Gain-Compression Measurement (GCA) software provides fast and accurate input power, output power, gain, and phase at the compression point of an amplifier or frequency converter over a specified frequency and power range. With a simple setup, GCA reduces test times through an easy-to-use, fast, and accurate SMART Sweep. GCA also includes a guided calibration that corrects for absolute power levels, frequency response, and mismatch errors.
-
Product
13MP MIPI Camera Module
e-CAM130_CUMI1820_MOD –
-
e-CAM130_CUMI1820_MOD is a 13MP MIPI Camera Module. This small form factor 13MP camera module comes with S-Mount lens holder. It is based on AR1820HS – an 18MP CMOS Image sensor from Aptina™ / ON Semiconductor® and has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images and video and the optional MJPEG compression. Though the AR1820HS is an 18MP image sensor, the e-CAM130_CUMI1820_MOD supports only up to 13MP resolution.
-
Product
Rubber Testing Equipment
-
Dongguan Amade Instruments Technology Co., Ltd
Rubber testing equipment are used to test the physical properties, chemical properties, thermal properties of uncompounded and compounded rubbers at prescribed conditions to help manufactures or researchers in comprehending the characteristics, updating the formula and improving product quality. Including volatile component, ash content, Mooney viscosity, vulcanization curve, Mooney scorch time, hardness, tensile properties, tearing, the compression performance, impact, friction resistance, fatigue resistance, peel strength, vertical & horizontal combustion, smoke density, limiting oxygen index, the flame spread rate, the surface resistance, surface resistivity, volume resistivity, the breakdown voltage, dielectric strength, dielectric loss, antistatic properties, Aging test (UV, Xenon lamp, carbon arc lamp, ozone) etc.
-
Product
Mechanical Testing
-
Our Capabilities*Flammability*Solderability and Solder Heat*Package and Drop Testing*Resistance to Chemicals and Solvents*Conformal Coat Compatibility*Compression and Tension Testing*Up to 10,000 pounds
-
Product
High Precision Compression Type Load Cell
IR
-
A high-precision compression-type load cell is a sensor that accurately measures compressive (pushing) forces, designed for applications requiring very tight accuracy and reliability. It works by converting a downward force into an electrical signal, often using strain gauges to measure deformation, and is used in demanding fields like calibration, manufacturing, and medical equipment.
-
Product
Ultrasonic Leak Detection Camera
Leakshooter LKS 1000-V.2
-
1st ultrasonic compressed air, gaz and vacuum leak detector with camera. Specialy dedicated to visualize the spots where compressed air is leaking, the LEAKSHOOTER LKS 1000 – V.2 has many other applications such as : steam trap monitoring, bearing monitoring, electrical applications like partial discharge, corona effects, punctured isolators, electrical tracking detection.
-
Product
Pouch Battery Housing
PBS1
-
A customizable square solid-state battery housing for laboratory assembly and compression testing, available in multiple configurations to meet different research requirements.
-
Product
Hydraulic Universal Testing Machines
HW Series
-
Control Software is used to control the Universal testing machine. The Tester and the software are designed to accommodate a wide variety of testing needs. The software has a variety of pre-set programmed test cycles for compression, tensile and cyclical testing to meet a variety of testing standards.
-
Product
Neodymium Compression Drivers
-
Lightweight and powerful, RCFs neodymium drivers are a reference in performance and reliability.
-
Product
Universal Testing Systems (Up to 600 kN)
5980 Series
-
Instron 5980 Series floor model testing systems are universal, static testing systems that perform tensile and compression testing; and also perform shear, flexure, peel, tear, cyclic, and bend tests. The 5900 Series are engineered for precision, built for durability, and offer the flexibility for changing requirements. They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator. 5980 Series floor models are robust, heavy-duty frames commonly used for testing high-strength metals and alloys, advanced composites, aerospace and automotive structures, bolts, fasteners, and plate steels. Frames are available in load capacities of 400 and 600 kN.
-
Product
Compressed Air Monitor and Alarm
SENTRY
-
The Edgetech Instruments Model SENTRY detects upset conditions in compressed air systems by constantly monitoring dew point and pressure at the system header or dryer output. The SENTRY alarms when a loss in pressure or high dew point is detected. This information is valuable in detecting compressor failures, system leaks, or drops in dryer performance. A pulsing audible alarm and strobe lamp provide quick notification of upset conditions. The SENTRY also provides a local display of pressure, dew point and system status as well as 4-20mA analog output and alarm relay contacts.
-
Product
Hybrid Socket
CSP/Ballnest
-
Any grid size available on 0.50mm pitch or larger. ZIF style socket using Aries solderless, gold plated pressure mount Spring Probe. The gold over nickel plated compression spring probes leave very small witness marks on the bottom surface of the device solderballs.
-
Product
Compressed Air RH+T+Tdp Sensor
T3111P
-
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
40N Switch Tester Coupling Implement Shell Pressure Test Device
CX-F01
-
Shenzhen Chuangxin Instruments Co., Ltd.
This device is according to the IEC60320-1 standard requirement to design. Appliance inlets designed for surface mounting and having a shroud of metal, are compressed in an appropriate test apparatus, an example of which is shown in figure 20. The spherical end of the jaws shall have a radius of 20mm±1mm. A force of 40N±2N shall be applied for 60s±6s through the jaws to the most unfavourable point half-way up the outer surface of the shroud, in a direction perpendicular to the axis of the shroud. After the test, there shall be no deformation or loosening of the shroud such as will impair the further use of the appliance inlet.
-
Product
Bench Top Ionizers
-
Point-Of-Use Ionizer, Adjustable (30-100 PSI) Compressed Air IonizerNeutralize Electrostatic Attraction (ESA) to control contamination by dislodging dust and debris attracted by static electricity.Detachable 7'' long ESD Protective Flexible Hose with Thumb Button Designed to for a wide range of motion and simple operation.Adjustable Balance (20 Volts) with Less Than 1 Second Discharge Time At 6 InchMeets required limits ANSI/ESD S20.20 tested per ANSI/ESDSTM3.1 and ESD TR53
-
Product
USB Audio/Video Codec
2253
-
Simultaneous encode/decode in a robust, compact unit Uncompressed + compressed outputs from one video input Low preview latency H.264 HP@L3, MPEG-4 ASP, MJPEG video compression AAC, G.711 audio compression, uncompressed PCM Text overlay Two general-purpose digital I/Os Industrial temperature range version available Transport Stream
-
Product
1Gsps, 9 Channel, Logic Analyzer with Protocol Analyzer plugins and Hardware Compression
DigiView™ DV509
-
- Physical Channels: 9- Sample rate: 4ch@1 Gsps or 9ch@500Msps (4 ch. are sampled every 1ns or 9 ch. are sampled every 2ns)- Typical capture: 100M transitions (> 1B samples)- Hardware based triggers with 8 universal match circuits, and partitionable 16 stage sequencer- Adjustable Threshold (± 4V)- Real-time, Hardware-based, Adaptive Compression- Channels protected to ± 20V- Ground leads protected to ± 12V- High-quality test leads: 66 strand soft copper wires, flexible insulation, and gold plated connectors. Fit .025 square posts as well as the included clips.- Extra ESD protection- Streaming storage with auto fall-back to Store & Forward mode ensures large storage and reliability.- USB 3.0 (SS) or USB 2.0 (High Speed)- USB powered- Each DigiVIew includes all avialable Protocol Analyzer plugins (including: I2C, SPI, CAN, Async, Sync, 1-wire, I2S, TDM)- Free Plugin Developers' Kit- Requires Windows 7 or greater OS (32bit or 64bit)- Free Lifetime sofware updates.- 1 year warranty
-
Product
Encoders
-
DekTec encoder cards use hardware compression chips to achieve very low CPU overhead. Ideal for converting the output of your video-generating application to H.264 in real-time, without consuming precious CPU cycles.
-
Product
Extensometers
-
Extension measurement is one of the areas that complements our range of UTM program. The result is a comprehensive range of high class variations. The product selection is arranged as follows:*Non-contact extensometers with and without measurement marks.*Contact extensometers: Sensor arm extensometers, incremental and analogue clip-on extensometers as well as extensometers for compression and flexure tests.
-
Product
Instron Materials Testing Software
-
Instron offers a comprehensive suite of materials testing software solutions designed to support a wide range of mechanical testing applications, from static tensile and compression to fatigue, impact, and melt flow. Built for precision and efficiency, these software packages provide powerful tools for test control, data analysis, and reporting, with support for industry standards such as ASTM, ISO, and EN. Whether for basic quality control or advanced research, Instron’s software solutions deliver flexible, user-friendly interfaces and robust data integrity features to meet the diverse needs of modern testing laboratories.
-
Product
1Gsps, 18 Channel, Logic Analyzer with Protocol Analyzer plugins and Hardware Compression
DigiView™ DV518
-
- Physical Channels: 18- Sample rate: 4ch@1 Gsps or 9ch@500Msps or 18ch@1Gsps (4 ch. are sampled every 1ns or 9 ch. are sampled every 2ns or 18 ch. are sammpled every 4ns)- Typical capture: 100M transitions (> 1B samples)- Hardware based triggers with 8 universal match circuits, and partitionable 16 stage sequencer- Adjustable Threshold (± 4V)- Real-time, Hardware-based, Adaptive Compression- Channels protected to ± 20V- Ground leads protected to ± 12V- High-quality test leads: 66 strand soft copper wires, flexible insulation, and gold plated connectors. Fit .025 square posts as well as the included clips.- Extra ESD protection- Streaming storage with auto fall-back to Store & Forward mode ensures large storage and reliability.- USB 3.0 (SS) or USB 2.0 (High Speed)- USB powered- Each DigiVIew includes all avialable Protocol Analyzer plugins (including: I2C, SPI, CAN, Async, Sync, 1-wire, I2S, TDM)- Free Plugin Developers' Kit- Requires Windows 7 or greater OS (32bit or 64bit)- Free Lifetime sofware updates.- 1 year warranty
-
Product
Leak & Seal Integrity Tester
-
Saicheng Leak Tester is professionally designed for the leakage tests of packages, bottles & pouches for food, drugs, medical instruments, household chemical products, cars, electronic components, stationeries and other industrial products. The instrument also can be used to test seal performance of specimens after falling and compression tests.
-
Product
75 Ohm BNC Connectors
-
Pasternack 75 Ohm BNC connector category contains many part numbers, most are RoHS and REACH compliant. 75 Ohm BNC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Pasternack 75 Ohm BNC connectors are built to precise RF and microwave industry specifications. 75 Ohm BNC connector are available in male or female gender with 75 Ohm impedance. BNC 75 Ohm connectors are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These 75 Ohm BNC connector designs include clamp/solder, compression, crimp/solder or solder attachment methods. We offer 75 Ohm BNC connector with standard or high performance levels constructed with brass or stainless steel bodies. Like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm BNC connector group is in-stock. In addition to being in stock, these BNC 75 Ohm connectors will ship the same day as they are purchased.
-
Product
Tensile/Compression/Bending/Torsion Testing Kits
-
With the constantly growing competitive pressure in today`s market are quality and product innovation basic requirements for any company.For this purpose TIRA is developing accurate and high quality material testing machines and testing systems which are manufactured according to the national and international standards DIN 5122, EN ISO 7500-1, GOST. With our testing machines you can carry out the static testing of metals, parts, wood, building materials, glass, plastics, fibers, composites etc.
-
Product
Ceramic Solid-State Battery Compression Test Cell
CSS1
-
Ceramic solid-state battery compression test cell with a 10 mm inner diameter, titanium alloy body, PEEK insulation, and ceramic liner for battery assembly and electrochemical testing.
-
Product
Encode & Transcode Cards
-
Advantech industrial encode and transcode card from multi-channel SDI/HDMI/DVI-D/DVI-A/YPbPr different hardware compression and dual streaming.
-
Product
Test Adapter / Pneumatic Adapter
-
GPS testing technology offers a wide range of pneumatic adapters. The support with compressed air results in increased ease of use and larger pressures can be built up easily and thus more test needles can be contacted.
