High Voltage Dividers
scales down very high voltage in order to measure. Also known as: HV Dividers
See Also: Voltage Dividers, HV Dividers
-
Product
High Voltage Pulse
-
For thicker coatings it has fully adjustable output voltage from 5 kilovolt to 25 kilovolts. For very demanding conditions, a sensitivity switch offers additional control.
-
Product
NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781397-01
Voltage Input Module
±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
Product
Brute High Current Probe
P4301-2F
High Current Probe
Current Rating (Amps): 50Current Rating Remark: 40 Amps for BeCu plungersAverage Probe Resistance (mOhm): 5Test Center (mil): 300Test Center (mm): 7.62Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 1,750Overall Length (mm): 44.45
-
Product
sbRIO-9205, Non-Enclosed, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
784787-01
Voltage Input Module
Non-Enclosed, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module - The sbRIO‑9205 performs single-ended or differential analog inputs, with four programmable input ranges for each. It is an effective combination of channel count and speed at a low price for an economical multifunction system. You can choose from four programmable input ranges. To protect against signal transients, the sbRIO‑9205 includes up to 60 V of overvoltage protection between input channels and common (COM). In addition, the sbRIO‑9205 also includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. It is rated for 1,000 Vrms transient overvoltage protection. Non-enclosed modules are designed for OEM applications.
-
Product
SHC68-C68-RDIO2, 68-Pin VHDCI Male to 68-Pin VHDCI Male, 80 MHz, Shielded Digital Cable, 2m
156166-02
High Speed Digital Cable
SHC68-C68-RDIO2 Shielded R Series High Speed Digital Male VHDCI Cable, 2m
-
Product
High Voltage Probes
-
High voltage measurements have a variety of different requirements, and our PVM series and VD series probes are designed for most of these requirements. The PVM probes are designed for wide bandwidth and ease of portability where a variety of measurements must be made. The VD series probes are designed for use at higher voltage ranges, and where physical stability is required.
-
Product
High Voltage Transformers
-
We, NMC, are engaged in manufacturing AC/DC High Voltage Transformers ranging from 5kv upto 150Kv having current capacity from 10mA to 200mA AC/DC in Air cooled or Oil Cooled type as per the customer requirement.
-
Product
LXI High Voltage Matrix
65-218-121-CC
Matrix Switch Module
The 65-218-121-CC is a plug-in module is part of a scalable high voltage matrix platform designed to provide a large matrix solution with a switching capacity of 1000V without access to the chassis backplane.
-
Product
High Voltage Testers
-
HV Test, which is also known as Hipot Test – short form of high potential – is used to test the insulation quality of the auxiliary circuit of circuit breakers. The HV Test is useful in finding damaged insulation, stray conductive materials around the conductors, and problems due to terminal spacing and tolerance errors in cables.
-
Product
High Voltage Phasing Sticks
9007KB Series
-
Shanghai Beha Electronics Co., Ltd.
*Important applications include checking voltage fuses, testing for correct phase connections, and for absence of high voltage on deenergized lines or apparatus.*measuring ranges from 6.6kV up to 44kV systems*Fiberglass is of hot stick quality and tested to IEC specs (100kV/300mm for 1 min). All front end (resistors) are encapsulated.
-
Product
Power Divider
-
Chengdu KeyLink Microwave Technology Co., Ltd.
The series of products are passive devices.The frequency range covered by 0.5GHz~40GHz.The products have the characteristics of good amplitude and phase consistency and low insertion loss.The products can be applied to all kinds of receiving and transmitting channels. KeyLink's power dividers can be categorized as follows.
-
Product
Power Dividers
-
Powers plitters can divide one signal into two or N way equal or non-equal energy, in reverse,they are also used as combiners by combining multiple signal into one. They are mainly used in feed network in antenna array, mixer and balanced amplifier, finish the work of distributing, combining and measuring power, isolating signal sources and measuring swept reflected coefficient etc.
-
Product
High Voltage, High Current Linear Amplifier
P200
-
The P200 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
-
Product
High Voltage Probe
HVP-40
-
*MAX. Voltage : DC : 40KV, AC : 28KV, (50/60Hz only) CAT II.*1000MΩ Input Impedance.*Accuracy **DC: ± 1% to 20KV. ± 2% to 40KV. **AC: -5% to -10% (50/60Hz)*Division Ration : 1000:1*CE, TUV GS, UL, CUL, IEC1010
-
Product
High Voltage Amplifier
HA-805
-
*800Vp-p(±400V DC) *200mAp-p(±100mA DC) *Bandwidth: ≦300KHz(400Vp-p) *Slew Rate: 300V/us *Gain(AMPL):0~180(10 Turn VR) *DC Offset: ≦0~±400V(10 Turn VR+SW) *Output Resistor: 100Ω *Microprocess Control Protection
-
Product
PCI High Voltage MUX
50-350-001
Multiplexer Module
The 50-350-001 is a Short PCI Card designed as a high voltage multiplexer for use in a Submarine Cable Testing Application. It is designed to allow the dynamic connection of various test instruments to 1 of 16 test points. The multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.
-
-
Product
High Voltage Probe
CP-3308R
-
*100:1 scope probe *300MHz Bandwidth *Read out Function *Division Ratio x 100 *100MΩ Fix Input Impedance *1500V DC Working Voltage (CAT Ⅱ) *2000V AC peak to peak MAX. (CAT Ⅰ) *CE Approved.
-
Product
High Voltage Probe
PL-10
-
*MODEL：PL-10*IMPEDANCE：1.111MΩ*ACCURACY： ±0.25%*FREQUENCY B.W.：DC~50MHz*WORKING POWER：MAX. 1Watt*INPUT VOLTAGE：MAX.250VDC or 200V rms AC*DIMENSION：46mm(L)xΦ16mm(D)*WEIGHT：25g
-
Product
High Voltage Probe
PD-28
-
Kusam Electrical Industries Limited
Most Digital Multimeters can measure AC Voltage up to 750 /1000V and DC Voltage upto 1000V DC. To extend the measuring range of the digital multi meter for low - power , high - voltage , high impedance circuits such as TV, Video Monitors.
-
Product
Brute Hight Current Probes
P4301
High Current Probe
Current Rating (Amps): 50Current Rating Remark: 40 Amps for BeCu plungersAverage Probe Resistance (mOhm): 5Test Center (mil): 300Test Center (mm): 7.62Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 1,750Overall Length (mm): 44.45
-
Product
High Voltage Products
-
Advanced Energy's high voltage products feature high-performance power supplies and amplifiers. Each product line features hundreds of units, options, and accessories to meet your application needs.
-
Product
Low Noise High Precision High Voltage Amplifier
WMA-280
-
The WMA-280 is a high voltage, low noise precision amplifier. Its specifications have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-280 can be used for MEMS actuation, EO-modulators, as high voltage driver for PZT (piezo) positioners, ultrasonics, and many other applications. Its output noise is only 300 microVolt rms.
-
Product
LXI High Voltage Switching
65-233-902-HI
Switch Module
The 65-233-902-HI plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
High Voltage Switching Systems
HXV Series
-
HXV products are high voltage systems intened for Hi-pot / IR or High voltage switching. They can be configured to drive from 32 to 128 switch points per chassis and can be configured as multiplexer (1xN) or Matrix (NxM) configurations. Stand HXV chassis are used for signals up to 5000 VAC rms ( 7400 V peak ) and can carry up to 5 amps of current. Custom systems can be built up to 25KV. Most of the modules used in these systems are 1xN multiplexers or 2x4 matrix modules that can be combined to form larger multiplexers or matrices. Connector options for standard HXV include 5 way banaba jacks / binding posts, Shrouded Banana Jacks or SHV ( High voltage BNC) if you need to use a high voltage cable with a grounded shield for safety applications. Control options include 10/100BaseT Ethernet LAN, RS232, GPIB or optional manual control. Standard HXV systems use high voltage reed relays. Custom HXV systems up to 25KV use application specific relays and connectors from a variety of vendors based on required specifications.
-
-
Product
High Voltage Seasoning Equipment
-
This equipment is used to remove the bars that are in contact with the surface of vacuum interrupters.
-
Product
Dividers
Universal™ TruFlow™
-
Universal TruFlow dividers improve material add-on accuracy and reduce material consumption by providing passive metering closer to the point of application. A single incoming adhesive stream can be divided, or separated, into as many as eight individual streams.
-
Product
High Voltage Power Supplies
-
Trust a high voltage power supply provider with 40-plus combined years of experience. Advanced Energy’s HiTek Power and UltraVolt product lines feature hundreds of units, options, and accessories to meet your application needs.
-
Product
High Voltage Dry Reed Relays
Series 60 & 65
-
High voltage relays - chassis mounted, up to 15kV. Tungsten switches with power rating of 50 Watts maximum. Series 60 has solder terminals and nylon chassis mounting studs
