Fading Simulators
test to verify wireless communicatons link in adverse transmission conditions.
-
Product
2 Port T1/E1/PRI ISDN Simulator
SIM-2PRI
-
The most inexpensive ISDN simulator on the market. This unit has two PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Basic Rate and Primary Rate Simulator
emutel Pro
-
Emutel Pro has the same features as the Emutel but has 2 BRI and 2 PRI which will allow you to test both basic rate or primary rate equipment or basic to primary links to be set up. Emutel Pro has optional network support and protocol analysis.
-
Product
ESD - Simulator
SESD 230
-
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
-
Product
Three-Dimensional Electromagnetic Simulation Package
QuickWave-3D
-
QuickWave 3D (QW-3D), is a universal user-friendly three-dimensional electromagnetic simulation package (winner of the European Information Technology Prize in 1998) based on the conformal FDTD method and supplemented with a range of unique models for curved boundaries, media interfaces, modal excitation, and parameter extraction. Complete 3D electromagnetic simulation offer a set of various results from wide area of applications. A lot of processing/postprocessings present a complete offer of comprehensive solutions from microwave components (filters, couplers, resonators, etc.) through antennas, TDR applications, optimisation and parameters sweep to simulation of microwave heating process (with Basic Heating Module) with temperature dependent media, static, rotated or moved heated object(s), and heat transfer.
-
Product
Single-Output Software-Defined GNSS Simulator
BroadSim Solo
-
Designed to address the permanent challenges that engineers face with laboratory capacity and availability, BroadSim Solo was developed to bring advanced GNSS scenario creation to your desk and propel development cycles.
-
Product
Single Or Dual Stream MIL-STD-1553 A/B &4, 8 Or 12 Channel ARINC429 Mixed ProtocolTest & Simulation Module For Standard Ethernet
ANET-MxAy
-
Single or dual stream MIL-STD-1553 A/B and 4, 8 or 12 channel ARINC429 mixed protocol Test & Simulation module for standard Ethernet. The ANET embedded Linux operating system gives the unique capability to run the optional PBA.pro Engine right in the box.Another option is the ANET-ADK onboard software development kit where users create runtime applications (e.g. MIL-STD-1553 to Ethernet Converter / ARINC429 to Ethernet Converter , MIL-STD-1553 to Ethernet Gateway / ARINC429 to Ethernet Gateway) to execute right in the box. For wireless applications an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET docking station to host up to 4 ANET modules.
-
Product
Force On-Force Reactive Tactical Readiness IADS Simulation
FORTRIS™
-
FORTRIS™ is a scenario engine that provides a real-time complex battle simulation between hostile and friendly forces. The Synthetic Environment within FORTRIS contains a true multi-layered Integrated Air Defense System (IADS) simulation that can act and react both as an overall system, as well as individual contributors, making it the ideal cognitive training tool within the Live Virtual Constructive (LVC) world.
-
Product
Infrared Simulation Services
-
INO offers a simulation service to assist with the hardware and software design of infrared and electro-optical devices. Precise performance predictions help integrators understand application requirements and bring application performance in line with client specificationsbefore the advance design and fabrication phases. For a minimal investment, infrared simulations help minimize risk in the early stages of development.
-
Product
LSI Structure Simulator
PARADISEWORLD-2
-
A high-speed and high-accurate simulator of LSI structure with graphical user interface. Capable to handle ULSI with ultra high-speed pattern layout viewer. Stable simulation evn for the complex profile.
-
Product
Multi-Parameter ECG Patient Simulator
SL-8 SimSlim®
-
The smallest, comprehensive multi-parameter patient simulator on the market. Includes ECG, Respiration, Arrhythmia, 4-IBP, YSI 400/700 Temperature, and Cardiac Output. Its patented power circuitry provides amazing battery life up to 10 years without charging or changing batteries! One button operation reduces the time for setup and completing testing. View the product manual on our User Manuals page.
-
Product
Educational Patient Simulator
EasySim®
-
The new and improved EasySim® arrhythmia simulator fits in the palm of your hand! The ultra-portable (6.6″ x 2.4″ x .5″), ultra-lightweight (10 oz.) remote control will place you on the leading edge of medical education technology. The highly intuitive design features 48 direct-access keys in a remarkably easy to use format. No codes to memorize! No fuss to set up!
-
Product
Voltage Dip, Interruption& Variation Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
PFS single phase power fail simulator simulates voltage dip, interruption and variation which are caused by power grid and transformer devices due to malfunction or sudden large change of load. It is required to test this kind of phenomena to check whether electronic and electrical device can sustain safety operating condition.
-
Product
PXI Analog Output/Current Loop Simulator Module - 4 Channel
41-765-004
-
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Time-Domain Electromagnetic Simulation
Meep
-
Massachusetts Institute of Technology
Meep is a free and open-source software package for electromagnetics simulation via the finite-difference time-domain (FDTD) method spanning a broad range of applications.
-
Product
AFDX ® /ARINC664P7 Networks Test, Simulation, Monitoring & Analyzer
ACE-FDX-3U-2
-
AFDX®/ARINC664P7 Test and Simulation module for PCIe x1 with 2 full duplex ports programmable for 10/100/1000 MBit/s. Versions available for both Airbus and Boeing variants of ARINC664P7. Test, verification and simulation of AFDX®/ARINC664P7 End Systems, Switches and Networks. Support for Single or Redundant AFDX®/ARINC664P7 operation. Support for Boeing ARINC664 extensions for EDE at the hardware interface layer.
-
Product
ESD - Simulator
SESD 216
-
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
-
Product
USB 2.0 SmartCable For MIL-STD-1553 Test And Simulation
ASC1553
-
The ASC1553 (AIM SmartCable) USB module offers full function test, simulation, monitoring and recording for MIL-STD-1553B applications implemented in an ultra compact form factor.
-
Product
Simulation Table
KRD61 6-DOF
-
KRD61 series 6-DOF simulation table is a closed-loop servo simulation platform consisting of six servo actuators and six sets of dedicated hinges connected at the top and bottom platforms respectively. By virtue of the telescopic movement of the six actuators, the upper platform moves in six degrees of freedom (X, Y, Z, α, β, γ), so various space motion attitudes can be simulated.
-
Product
Diagnostic Simulation
Stage
-
STAGE simulates aspects of Diagnostic, PHM and ISHM Engineering, showing the support capabilities of a System during its useful lifetime. Many types of analysis can be performed on STAGE, including Testability, System Reliability & Mission Success, Sustainability, and Logistics Resource Allocations.
-
Product
Test & Simulation Interface for PCI
PCI-C1760
-
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI
-
Product
Multiphysics Simulator
-
The COMSOL Multiphysics simulation environment facilitatesall steps in the modeling process defining your geometry, specifying your physics, meshing, solving and then post-processing your results. Model set up is quick, thanks to a number of predefined modeling interfaces for applications ranging from fluid flow and heat transfer to structural mechanics and electromagnetic analyses.
-
Product
Temperature Simulators
-
A single select button scrolls quickly between the 3 factory set calibration points for efficiency. Two models to choose from: 271-018 (0°F, 32°F, 212°F) and 271-019 (32°F, 212°F, 500°F). Each unit includes a 3-point UKAS Accredited Calibration Certificate so you know that you''re using a precision instrument. Also included is a 3 foot type K test lead for connecting up your type K meters. You get precision at an economic price. Simple and fast!
-
Product
MIL-STD-1553 Test & Simulation Instrument for VXI
VXI-1553
-
Avionics Interface Technologies
Dual redundant, multi stream configurations availableSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Real-Time recording and physical bus replayANSI Application interface supporting C, C++, C#, and .NET development - VISA based VXI “Plug & Play’ Device driver provided
-
Product
ARINC 429 Test And Simulation PCI Module
PCI-C429
-
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
AC drives, Soft-Starters or Servo Drives Simulation Software
-
Product simulation software enables users to operate, program and simulate AC drives, Soft-Starters or Servo Drives directly from their computer without having the actual product present or connected. Our simulation software can be used as a demonstration tool during a sales meeting or as an interactive tool for training classes. Software available In addition we offer simulation software for dedicated markets such as pumping, mining, material handling, etc... to demonstrate the use of motor controls in simulated applications.
-
Product
Ray tracing and Laser Simulation / Cavity Design Software
LasEasy V1.0
-
LasEasy software is the professional software for simulating and designing solid-state laser cavity, optical amplifier system, and parametric OPO systems. It can also simulate the laser light propagation in both horizontal and vertical (sangital and tangitial) planes.
-
Product
NIBP Simulator
SC-3 SimCube®
-
This NIBP only simulator provides features to perform basic NIBP testing of a patient monitor. Features one-button operation for quick testing of patient monitors and optional Battery Boost Option. Optional accessories provide all you need to test the NIBP parameter on any type of patient monitor.
-
Product
Solar Simulator
-
It is an LED light source for evaluating the performance of organic solar cells in indoor light applications.A neutral white LED light source equivalent to a color temperature of 5000 K, achieving an effective irradiation area of 50 × 50 mm.The illuminance can be changed without changing the height of the light emitting surface with low illuminance (200 lx) and high illuminance (1000 lx).
-
Product
Interior light simulator
-
It is possible to evaluate characteristics of various solar cells and various sensors with high precision under LED lighting. It is possible to evaluate output characteristics conforming to JEITA standard ET - 9101 *
