Isolated Digital Input Cards
-
Product
PXIe-4310, 16-Bit, 8-Channel, 400 kS/s/ch, Ch-Ch Isolated PXI Analog Input Module
784813-01
-
16-Bit, 8-Channel, 400 kS/s/ch, Ch-Ch Isolated PXI Analog Input Module—The PXIe-4310 is a channel-to-channel isolated, filtered analog input module for higher voltage measurements. The module offers the ability to select an analog filter per channel to provide extra filtering performance. You also can operate up to four different input ranges per terminal block and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI-DAQmx driver simplifies hardware configuration and measurement.
-
Product
PXI 32 Channel I/O Serial I/P Prog Threshold
40-412-001
-
The 40-412 is a 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels
-
Product
PXI-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module
778858-01
-
96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module—The PXI‑6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
NI-9211, 4-Channel, 14 S/s/ch, ±80 mV C Series Temperature Input Module
779001-01
-
4-Channel, 14 S/s/ch, ±80 mV C Series Temperature Input ModuleThe NI‑9211 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The NI‑9211 features NIST‑traceable calibration and a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range.
-
Product
NI-6584, 16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
781290-03
-
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter module for FlexRIO can be used to do real-time interfacing and analysis of RS485 and RS422 as well as other electrically compatible interfaces. The NI-6584 can sample digital waveforms at up to 100 MHz clock rates, has terminated and unterminated options, and full and half duplex configurations.
-
Product
PXIe-7820, Kintex 7 160T FPGA, 128 DIO, PXI Digital Reconfigurable I/O Module
783484-01
-
Kintex 7 160T FPGA, 128 DIO, PXI Digital Reconfigurable I/O Module—The PXIe‑7820 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7820 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7820 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
1.6 GSPS, 14-bit RF Digitizer
ADQ1600RF
-
The ADQ1600RF (formerly named ADQ1600) is a world-leading 14 bit digitizer. With its unique 1600 MSPS capture rate, enabled by SP Devices’ ADC interleaving technology ADX, the ADQ1600RF opens for demanding measurements such as RF/IF sampling, high resolution ultra sound imaging and high-speed data recording.
-
Product
C Series Universal Analog Input Module
-
The C Series Universal Analog Input Module helps you perform multi-purpose measurements. This module includes built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. You also can choose options to measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors.The C Series Universal Analog Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
PXIe-4464 , 204.8 kS/s, 119 dB, 6 Gains, AC/DC-Coupled, 4-Input PXI Sound and Vibration Module
783087-01
-
204.8 kS/s, 119 dB, 6 Gains, AC/DC-Coupled, 4-Input PXI Sound and Vibration Module—The PXI‑4464 delivers simultaneous sampling on all channels. In addition, the PXI‑4464 includes built-in antialiasing filters that automatically adjust to your sampling rate, six software-selectable input gains ranges, and TEDS smart sensor support for error-free setup. The IEPE excitation circuit can deliver current for high-power sensors and strong data integrity over long sensor cable runs.
-
Product
PXI Digital IO: 32 inputs, 32 outputs, 0.3V to 50V
M9187A
-
The M9187A has 32 input channels that can be used for comparing inputs to user-defined thresholds between 0.3V and 50V, with 12mV setting resolution. Each input is protected up to 100V. In addition, the 32 output channels use a high current to drive the output high or low, and are capable of sourcing 0.4A from the high side or 0.5A sink from the low side of each channel. These outputs are protected against over-voltage or over-current conditions. Choose from the durable connector block or the standard cable connections.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 40 Channels
DN6.593-40
-
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
PXIe-7822, PXI Express Digital RIO with Kintex-7 325T FPGA
783486-01
-
Kintex 7 325T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7822 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7822 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
PXIe-5774 , 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PXI FlexRIO Digitizer
785646-02
-
The PXIe-5774 provides up to 3 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PXIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset. The PXIe-5774 is ideal for time-domain measurements in areas such as scientific instrumentation, medical imaging, and particle physics. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
SHC68-C68-RDIO2, 68-Pin VHDCI Male to 68-Pin VHDCI Male, 80 MHz, Shielded Digital Cable, 1m
156166-01
-
SHC68-C68-RDIO2 Shielded R Series High Speed Digital Male VHDCI Cable, 1m
-
Product
PXIe-4302, 24-Bit, 32-Channel, 5 kS/s, ±10 V PXI Analog Input Module
783865-01
-
24-Bit, 32-Channel, 5 kS/s, ±10 V PXI Analog Input Module—The PXIe‑4302 is a filtered input module for voltage, thermocouple, and current measurements. The module has an A/D converter per channel to enable a simultaneous sample rate of 5 kS/s. The PXIe‑4302 offers you the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
Product
Synchro to Digital-Resolver to Digital Converters
HSDC-HRDC
-
Computer Conversions Corporation
HSDC & HRDC Series are Miniature, Tracking Synchro and Resolver to Digital Converters with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command for military and industrial applications.
-
Product
PXIe-7821, Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module
783485-01
-
Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7821 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7821 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7821 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in-‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
Digital and Serial I/O
-
At Abaco, we're committed to the future of your VME systems, and we provide you with the flexibility and functional density you need.
-
Product
PXIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4X.2230-X4
-
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 2.5 GS/s on 4 Channels, 1.5 GHz Bandwidth
DN2.222-04
-
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
SH68-68-D1, Shielded Cable, 2 m
183432-02
-
68-Pin, Female D-SUB to 68-Pin, Female D-SUB, Twisted Pair, Shielded Digital Cable - The SH68-68-D1 Digital Cable connects NI 6533/4 digital instruments and NI 660x or 661x counter/timer modules to 68-pin accessories. This shielded cable features twisted pairing and is offered in different lengths.
-
Product
2 Ft. Shielded Cable For All 5xxx/35xx (68 Pin)
GT95021
-
2' shielded cable for 5xxx/35xx products (68 Pin)
-
Product
PXI FlexRIO Digitizer
-
PXI FlexRIO Digitizers feature high-performance analog-to-digital converters with lightweight analog front-ends designed to maximize sample rate, bandwidth, and dynamic range. These modules use FPGAs from Xilinx alongside LabVIEW and Vivado programming options for custom algorithm implementation and real-time signal processing. For applications that require high channel counts, PXI FlexRIO Digitizers use the NI-TClk API and the timing and synchronization capabilities of PXI to achieve sub-sample synchronization between multiple modules in a chassis. These modules also feature an auxiliary I/O connector with GPIO for triggering or digital interfacing and the option for high-speed serial communication.
-
Product
NI-9472, 24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module
783907-01
-
24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module - The NI‑9472 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 30 V, … features transient overvoltage protection between the output channels and the backplane, and has an LED that indicates the status.
-
Product
NI-9435, ±5 VDC to ±250 VDC/10 VAC to 250 VAC, 4-Channel (Sinking/Sourcing Input), 3 ms C Series Digital Module
779010-01
-
±5 VDC to ±250 VDC/10 VAC to 250 VAC, 4-Channel (Sinking/Sourcing Input), 3 ms C Series Digital Module - The NI‑9435 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel accepts signals from ±5 VDC to ±250 VDC and 10 VAC to 250 VAC; features transient overvoltage protection between the input channels and earth ground; and has an LED that indicates the status. The NI‑9435 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization when installed in a CompactDAQ chassis.
-
Product
Isolated USB To RS-232/422/485 Converter
ADAM-4561
-
Power from the USB portHot swap function supportedIsolation protection 3000 VDC providedAutomatic RS-485 data flow controlTransmission speed up to 115.2 kbps
-
Product
Digital Output Board
VME-2533
-
VME-2533 32-bit Differential Digital Output Board. VMEbus specification compatible double height form factor.
-
Product
PCI Express Graphics Cards With NVIDIA RTX 4000 SFF Ada
NVIDIA RTX 4000 SFF Ada
-
- NVIDIA Ada Lovelace Architecture- Half height, half length design- PCIe Gen4x16 interface- 20GB GDDR6 Memory, 160-bit Bandwidth- 6144 CUDA Cores, 19.2 TFLOPS SP Peak- 192 Tensor Cores, 106.8 TFLOPS- 4 x mDP (mini Display Port 1.4), 1 x USB-C
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 40 MS/s on 4 DAQ Channels and 4 AWG Channels
DN2.813-04
-
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
Embedded MXM GPU Module with Embedded NVIDIA RTX™ A4500
EGX-MXM-A4500
-
- NVIDIA Ampere Architecture- Standard MXM 3.1 Type B (82x105 mm)- PCIe Gen 4 x16 interface- 5888 CUDA® cores, 46 RT Cores, and 184 Tensor Cores- 17.66 TFLOPS peak FP32 performance
