Isolated Digital Output Modules
-
Product
PXI-2575, 196‐Channel, 1-Wire PXI Multiplexer Switch Module
778572-75
-
196‐Channel, 1-Wire PXI Multiplexer Switch Module —The PXI‑2575 is a high‐density PXI multiplexer switch module that is ideal for high‑channel‑count automated test applications. It uses electromechanical relays and can route hundreds of signals to measurement devices or from source units. The PXI‑2575 also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Single Channel
40-204-001
-
The 40-204-001(PXI) and 42-204-001 (PXIe) are single channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP12T, 18 GHz, 50 Ω, SMA, Remote Mount, Failsafe
40-788-221-E
-
The 40-788-221-E (PXI) and 42-788-221-E (PXIe) are single failsafe SP12T 18 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
Quad 2-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-011
-
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
PXI Prototyping Module, 2-Slot, 78-Pin D-Type
40-225A-402
-
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 26.5GHz, 50Ω, SMA, Remote Mount
40-785C-431-E
-
The 40-785C-431-E (PXI) and 42-785C-431-E (PXIe) are single SP4T 26.5GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI Very High Density Multiplexer, 24-Channel, 8-Pole
40-675A-002-24/8
-
The 40-675A-002-24/8 is a 24-channel, 8-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
IO60-DIO48 Module
IO60-DIO48
-
WINSYSTEMS’ IO60-DIO48 Module adds GPIO to embedded systems with IO60 expansion featuring 48 GPIO (General Purpose Input-Output) tolerant to 30 V DC. The SPI interface is implemented through the MACH XO2 SPI-slave EFB (Embedded Function Block) interface. Each bit of each port is implemented as a bi-directional tristate driver. Each bit of each port can also be configured and enabled to detect rising and/or falling edge events and generate a system interrupt.
-
Product
PXI/PXIe MEMS RF Multiplexer, Single 4-Channel, 4GHz, 50Ω, SMB
42-878-211
-
The module is based on the latest micro-electromechanical system (MEMS) switching technology and has low insertion loss and VSWR. In addition, MEMS devices have a long operational life of >3 billion operations and benefit from an operating time of <20 μs allowing greater test system throughput. The multiplexers have excellent and repeatable RF characteristics beyond 4 GHz with each path having a nominally equal insertion loss.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 3 GHz, 50 Ω, N-Type, Terminated, Remote Mount, Failsafe
42-785C-562-TE
-
The 40-785C-562-TE (PXI) and 42-785C-562-TE (PXIe) are dual failsafe SP6T 3 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-222
-
The 40/42-860A-222 is a PXI/PXIe dual insert/bypass switch with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PCI 2 Amp Multiplexer, Dual 16-Channel, 1-Pole
50-635A-105
-
The 50-635A-105 is a dual 16-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 67GHz, 50Ω, SMA-1.85
40-785C-573-E
-
The 40-785C-573-E (PXI) and 42-785C-573-E (PXIe) are triple SP6T 67GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI High Density Multiplexer, 4-Bank, 16-Channel, 1-Pole, Screened
40-610A-014
-
The 40-610A-014 is a screened 4-bank, 16-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 6-Channel, 2-Pole
42-514-104
-
The 40-514-104 (PXI) and 42-514-104 (PXIe) are low density multiplexers in dual 6-channel, 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
Product
PXI 2 Amp MUX, Single 8-Channel 4-Pole
40-635-103
-
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Signal, Module, ID, CASS, 64 Position, Center PCB Mount
510114109
-
Signal, Module, ID, CASS, 64 Position, Center PCB Mount
-
Product
Phi6 Drivers
-
Phi6 is the software environment to manage, control and program 6TL modules and systems.
-
Product
PXIe Microwave Multiplexer, Triple SP6T, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-784B-033-E
-
The 40-784B-033-E (PXI) and 42-784B-033-E (PXIe) are triple failsafe SP6T 26.5 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-901-HI
-
The 65-231-901-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-101
-
A 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 180 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.827-02
-
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
PXI 3A Power MUX BRIC, 4-Channel, 12-Pole
40-571-301
-
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI Single SP4T MUX 40GHz 50Ω SMA-2.9
40-784-141
-
Pickering Interfaces’ 40-784 PXI Microwave Multiplexer Modules have a characteristic impedance of 50 Ohm and are capable of switching signals up to 40GHz. Available in single or dual SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
Isolated DC Input/Output Module
ADAM-3014
-
1000 V DC , fully isolatedEasy input/output range configurationLow power consumption, 0.85 W (Voltage Output)Wide input/output rangeFlexible DIN-rail mountingOperates from single +24 VDCTemperature range 0 to 70°C
-
Product
PXI Monitored Multiplexer, Dual 64-Channel, 1-Pole
40-619-302
-
The 40-619-302 is a high density PXI 2 A multiplexer module in dual 64-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC - Single
-
Product
PXI/PXIe RF Multiplexer, Quad 4-Channel, 3GHz, 75Ω, SMB
40-832A-004
-
The 40-832A-004 (PXI) and 42-832A-004 (PXIe) are 75 Ohm 4 to 1 RF multiplexers with 4 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
FlexRIO Adapter Module Development Kit for Modular I/O
780711-01
-
FlexRIO Adapter Module Development Kit for FlexRIO—The FlexRIO Adapter Module Development Kit (MDK) for Modular I/O enables you to choose the specific converters, buffers, connectors, and other components so that you can build the exact analog and digital I/O you need into a custom adapter module for FlexRIO. NI recommends that you have custom printed circuit board (PCB) design and hardware description language (HDL) code development experience to use the FlexRIO Adapter MDK for Modular I/O.
-
Product
PXIe-4081, 7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter
783130-01
-
PXIe, 7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter—The PXIe‑4081 is the industry’s most accurate 7½‑digit DMM and provides the measurement capabilities found in two common test instruments: a high-resolution 1,000 V DMM and a digitizer. As a DMM, the PXIe‑4081 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, and frequency/period measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXIe‑4081 can acquire waveforms at sample rates up to 1.8 MS/s.
-
Product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781263-01
-
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
