Loop backs
connect input to ouput to test I/O loop.
-
Product
Temperature Loop Control Setup
ULP-27
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Temperature Control Loop Setup is basically a PC based PID controller setup used for closed loop and open loop analysis of temperature process system. The setup comprises of RTD temperature Sensor. The water flows through the Rotameter and Process tank to which a heating coil is fitted. The heater is controlled by a Thirstier drive. The Thirstier drive is connected to PID controller. The manual control valve can control the water flow. The system is mounted on a tabletop model with all necessary Piping. Water at approx. 100 LPH has to be supplied to a system externally. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
Product
Back and Forth Scratching Tester
WGQ-60
-
Shanghai Dean Electrical Co., Ltd
Executive standard: NEMA、JIS; Inspection standard: JB/T4279.15-2008Used to detect the scraping resistance of coating and cable insulation layer of flat wires of 0.800～5.600mm (narrow side) and the silk and enamel covered round wires with nominal conductor diameter of 0.100～5.000mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Sample support table allows for parallel rise and fall, maintaining close contact between the entire plane with sample;Scratching needle is vertical to the paint scraping direction and parallel with sample supporting table;When film is scratched and the action current is ≥5mA, painting scraper would automatically stop scraping;LED would automatically display the number of scraping.
-
Product
Active Loop Antenna
KH30935
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH30935 active loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna has a small outer diameter and light weight, which is convenient for outdoor measurement.
-
Product
Local Loop Simulator 128 Channels
458-CC-16/458-CM
-
FEATURES: Accepts 1 to 16 Line Modules; User-Friendly Interface; Multiple Configurations; Field-Upgradeable Software; One-Year Warranty/Calibration. The 458 Series 16-slot Chassis, which consists of the 458-CC chassis and one of three control modules, provides a wide variety of configurations through use of up to 16 plug-in Line Modules.
-
Product
Loop Calibrator
Model KM CAL-904-MK1
-
Kusam Electrical Industries Limited
• 4-20mA (1kΩ Load, 24V Loop Output).• 0-20mA and 0-24mA output ranges.• 0.025% Basic Accuracy.• Auto Ramp and Step functions.• 0-100% output with percentage step option.• 0-24V DC voltage source.• Open loop and overload buzzer alarm.• Low battery indication.• Simple Operation Interface• Warning beeper when output is open• Pollution Degree 2.• Ambient temperature 0~40℃.• Power Consumption 150mA at 24V 1kΩ load
-
Product
Single Loop Controller
1460
-
he 1460 has been designed to provide immediate visibility to the operator. At a glance, the programmable displays will show you the measured variable, the set point and the parameter being edited, the number of cycles or time remaining, the recipe name and number and also whether the cycle is in a ramp or soak mode
-
Product
1310/1550 nm Dual Laser Source Back Reflectiom/Power Meter
GM8019 + GM83001E
-
The UC INSTRUMENTS GM8019 + GM83001E 1310/1550 nm dual laser source back reflection meter and power meter is a compact, direct display instrument for the convinent measurement of backreflection, insertion loss and power connector, fiber optic components, and system. With a single output port, the meter is very easy to use and ideal for fiber cable jumper manufacturers.
-
Product
Back Pressure Spring For Vacuum Adapter
-
The counterpressure spring for vacuum adapters ensures that the board carrier plate with the test specimen is lifted off the needle bed at the end of the test.
-
Product
Spring Back Tester
HTJ-16
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.4-2008Used to measure the spring back characteristic of enameled round wires with nominal conductor diameter of between 0.080mm and 1.600mm;Number of winding turns: 5 turns and a halfStop accurately at zero position of the scale after automatic windingAs soon as the value of spring back angle stop counting, the dial will stop to rotate immediately, so that the value displayed on LED and read on the dial are the same.Sensor is unnecessary to be adjusted for samples of different specificationsCoils loosen slowly during spring back, no action of spring back or jump suddenly.Application of SCM control allows for fast operation and strong anti-interference capacity;
-
Product
U Type Glow Wire Loop
IEC60695-2-10
-
Shenzhen Chuangxin Instruments Co., Ltd.
Thermo resistance, spare part set of Glow Wire Apparatus Acc IEC60695-2-10. Thermo resistance loop is a wire loop that is defined at a temperature and is pressed against a standardized test platelet made of plastic (or other materials) for a prescribed period of time under precise test conditions.
-
Product
Phase Locked Loop with Integrated VCO
-
PLL with integrated VCOs provide local oscillator sources and clock sources for communications (COMMS) , test and measurement (ETM) and aerospace/defense (ADEF) applications. ADI's PLLs with integrated VCO portfolio includes both narrowband and wideband parts, supporting frequencies up to 13.6GHz. Our PLLs with integrated VCO, as well as our full PLL portfolio including integer-N and fractional-N PLLs, feature best-in-class performance for phase noise, jitter, and spurious, and also feature high levels of integration in small form factor packages.
-
Product
Loop A Line Products
-
Cable pair tracing and a lot more, Loop-a-Line products can remotely control a far end device (the oscillator) for up to 20km of cable. Using a Loop-a-Line allows the linesman to remotely change the state of the oscillator to any of five different states. Therefore eliminating the need for multiple journeys along the cable path.
-
Product
Dual Loop Master Controller
-
The Xcite System Master Controller provides all dual loop functions needed for accurate closed loop control and display of the static and dynamic test variables, while producing the highest electro-hydraulic frequency response. At the heart of each Xcite System is the Master Controller, a compact electronic control package which provides all of the controls and displays necessary to operate a controlled force or torque exciter system. The Xcite Master Controller is unique in that it provides electro-hydraulic excitation over a broad frequency range, unprecedented by any previous electro-hydraulic excitation system. It achieves its great frequency range through the use of sophisticated circuitry, high voltage inputs to the servovalve and compression control of the dynamic feedback variable in addition to the conventional servo control of the static loop. Static parameters such as force or displacement may be matched with dynamic control variables such as force, displacement, velocity, acceleration or strain for maximum test flexibility.
-
Product
Loop Testing
-
Megger loop testers offer both traditional measuring techniques and state of the art “non-RCD Tripping” technology. Use these products to determine the prospective earth fault current, which is the maximum current able to flow in a phase-earth fault in an installation, and also to indicate the prospective short circuit current which is the maximum current able to flow in the event of a phase-neutral fault.
-
Product
Opto-Isolated Current Loop Signal
4029
-
SPECTEC Innovative Sensor Solutions
SPECTEC's Model 4029 digital opto-isolated current loop signal conditioner prevents ground loops and interrupts any galvanic signals riding on magnetic speed sensor's output signal.. This signal conditioner converts magnetic, variable reluctance and inductive sensors' sinusoidal signals into a 4-20 mA output suitable for interfacing with process control units, dataloggers, flow controllers, and computers.
-
Product
Push Back Probes (VF3) HVF3SHAT
1007876
-
The Push Back Probes (VF3) HVF3SHAT is engineered to meet the rigorous demands of modern applications, ensuring a secure connection and reliable performance. With an internal thread of 2.0X0.2, this probe is designed for optimal functionality in conjunction with compatible tools, such as the FAWZVF3 receptacle tool and the 1007887-FAWZVF3 probe tool. This ensures seamless integration and convenience during use, making it a versatile choice for various projects.
-
Product
36" Front to Back Stiffeners
FB-36
-
Additional aluminum extruded front-to-back stiffeners are available for Vertical Cabinets. Includes installation hardware
-
Product
Peel Back Force Tester
PBFT
-
Precisely measure the peel back force of carrier tape to verify your packaging systems are within specification. Results can be printed and stored with the outgoing product.
-
Product
4-20mA Current Loop D/A Converters
-
ADI integrated solutions combine both the D/A converter and driver in one chip to provide the required output directly from the digital domain. Analog Devices’ portfolio of leading industrial D/A converters and drivers provides a range of programmable output ranges from standard 4 mA to 20 mA for current loop communication to ±10 V for actuator control. ADI industrial converters offer considerable control functionality and advanced on-chip diagnostics to maximize system uptime, as well as eliminate the need for costly calibration routines needed by some traditional discrete architectures.
-
Product
Current Loop Expansion Kit
OP-SB85C
-
This expansion kit supports current loop communications.The kit incorporates a communications circuit with photo-coupler isolation and constant-current power supply of insulated type, thus realizing not only monitoring but also easy communications testing with passive or active current loop devices.
-
Product
Push Back Probes (VF100) VF10017B150G15
1002250
-
The Push Back Probes (VF100) VF10017B150G15 are specialized contact probes designed for high-performance applications, featuring a robust and precise structure that ensures reliable connectivity even under extreme conditions. With an operating temperature range of -45°C to +100°C, these probes are ideal for environments requiring durability and reliability. Their design incorporates a basic contact probe with a pitch of 2.54 mm (100 mil), suitable for a variety of electronic applications.
-
Product
Push Back Probes (VF3) VF317B230G15
1005901
-
The Push Back Probes (VF3) VF317B230G15, order code 1005901, is an advanced basic contact probe designed for high precision and reliability in various technical applications. Engineered to function within an impressive temperature range of -45°C to +100°C, these probes are built to withstand demanding conditions while providing accurate performance. The probe's design utilizes beryllium copper for the plunger, plated with gold, ensuring excellent conductivity and durability. Coupled with its brass barrel, also gold-plated, this probe offers exceptional resistance to wear and corrosion, making it suitable for a multitude of uses in electronic testing and measurement environments.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 8 Channel
43-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
PXI Analog Output/Current Loop Simulator Module - 4 Channel
41-765-004
Analog Output Module
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Dynamic Scale Deposition Loop System
-
Dynamic Scale Deposition Loop fully automated systems includes hardware and software to measure and evaluate the performance of scale inhibitors under high pressure and high temperature conditions.
-
Product
Modular Breakout System for Hardware-In-Loop Simulation
-
Designed in partnership with OPAL-RT Technologies, this Modular Breakout System combines a BoB feature set with the added flexibility of an FIU. By mating the FIU chassis directly to the BoB using our plug-in modules, cabling is minimized, creating a more compact reliable design and improving signal integrity.
-
Product
Classic Collet | Back | Without Line | Matt Or Glossy | Ø 10 Mm
020-2x20/5
-
Secure plastic mounting cap for collet or wing knob
-
Product
Push Back Probes (VF3) VF383B0002G15
1005896
-
The Push Back Probes (VF3) VF383B0002G15 is a high-precision contact probe designed for reliable performance in a variety of demanding environments. With a temperature range of -45°C to +100°C, this probe ensures that it can operate effectively under extreme conditions. Its robust construction features a beryllium copper plunger with gold plating, providing excellent conductivity and corrosion resistance. The brass barrel, also gold-plated, complements the design, ensuring durability and reliability during use.In terms of functionality, the VF3 probe boasts impressive specifications. The continuous current rating is 8.00 A with a typical contact resistance of just 30.00 mOhm, minimizing energy losses and enhancing efficiency. The mechanical specs of the probe include a preload of 300 cN and a spring force of 1500 cN, enabling the probe to maintain consistent contact under various pressures. With an impressive pointing accuracy of ±0.10 mm and a nominal travel of 5.00 mm, this probe is engineered for precision in measurement applications.
-
Product
Push Back Probe (VF4) VF483B0001G15
1005203
-
The Push Back Probes (VF4) VF483B0001G15 are designed for high performance in various applications, extending their utility across multiple industries. With a basic contact probe design, these probes offer a pitch of 4.00 mm (157 mil) and are built to endure a wide temperature range from -45°C to +100°C. They are engineered to deliver reliable results, showcasing a continuous current rating of up to 10.00 A and maintaining a typical contact resistance of just 30.00 mOhm, ensuring optimal conductivity and minimal energy loss.
-
Product
Push Back Probes (VF4) VF483B0004G20
1005189
-
The Push Back Probe (VF4) VF483B0004G20 is designed for precision and reliability in various applications, featuring a basic contact probe design that ensures excellent performance. With a pitch of 4.00 mm (157 mil), this probe is capable of withstanding temperatures ranging from -45°C to +100°C, making it suitable for demanding environments. Its robust electrical specifications include a continuous current rating of 10 A and a typical contact resistance of 30 mOhm, ensuring efficient electrical connectivity.
