PXI DAQ
-
Product
48 Channel Threshold Comparator FPGA PXI Card
GX3748
cPCI Card
The GX3748 is a user configurable, FPGA-based, 3U PXI card which features 48 voltage comparator channels. The daughter board interfaces to the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA. Each input channel can accept input voltage signals from 0 to 50 volts, with programmable threshold levels. Three of the 48 channels are supported by the board's timestamp event feature.
-
Product
PXI High Density MUX BRIC, 16-Chan, 40-Pole
40-570-214
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI Sound and Vibration Module
Sound and Vibration
PXI Sound and Vibration Modules are designed specifically for applications like audio test and measurement, noise and vibration diagnostics, machine condition monitoring, automotive test, noise, vibration, and harshness(NVH) analysis, and laboratory research. They provide software-configurable AC/DC coupling, antialiasing filters, and IEPE conditioning to ensure precision measurements with microphones, accelerometers, and other transducers with large dynamic ranges.
-
Product
PXI 5A Fault Insertion Switch 20-Chan 2-Bus
40-198-002
Fault Insertion Unit
The 40-198 is a 20 Channel Fault Insertion switch, primarily designed for the simulation of fault conditions in automotive/avionics applications involving the reliability testing of safety critical controllers.
-
Product
PXI Single Transfer Switch 40GHz 50Ω SMA-2.9
40-782-541
Switch Module
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
Product
PXI 12xSPST High Voltage Power Relay Module
40-330-003
Relay
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.
-
Product
PXI 18x12 Matrix Module, 1-pole 2A 60W
40-508-001
Matrix Switch Module
The 40-505/506/507/508/509 are a range of medium density matrix modules able to switch up to 2 Amps or 300VDC/250VAC. They are constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
PXI 16x16 Matrix Module, 2-Pole, 2A, 60W
40-582-001
Matrix Switch Module
The 40-582 is a 256 crosspoint PXI matrix with dual pole switching. The module consists of a 16x16 matrix of 2-pole electro-mechanical relays with 2A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems. The user signal connection is via a robust 78 pin D-Type connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
-
Product
PXI Strain/Bridge Input Module
Strain/Bridge Input Module
PXI Strain/Bridge Input Modules feature up to eightchannels that support quarter-, half-, or full-bridge sensors at speeds up to 102.4kS/s. The modules provide increased accuracy, high data throughput, and a range of synchronization features. Optional features include remote sensing, internal bridge completion, and shunt calibration options per channel. PXI Strain/Bridge Input Modules are ideal for dynamic strain, load and pressure measurements, and test cell installations requiring accuracy and flexibility.
-
Product
PXI 8 Slot 3U
-
Comtel PXI Backplanes 8 Slot 3U. A number of versions are available that cover a wide range of needs. If you have a requirement for PXI Backplanes and/or Systems, please contact Comtel for further information.
-
Product
64-CH 12/16-Bit Up to 3 MS/s Multi-Function DAQ PCI Express Cards
DAQe-2200 Series
Data Acquisition Module
ADLINK DAQe-2200 series are highdensity and high-performance multi-function DAQ PCI Express cards. The devices can sample up to 64 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with high-density analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 32 AI channels in order to achieve maximum noise elimination.
-
Product
PXI Switch - 4x8 2-Wire Matrix Module
PXI-7931
Matrix Switch Module
ADLINK PXI-7931 is a matrix module with 32 cross-point 2-wire relays (DPDT, 2 Form C). The default configuration of the PXI-7931 itself is a 4-group 2x4 2-wire matrix. With the termination board, TB-6231, users could flexibly choose one of the configurations: one 4x8, two 4x4, one 2x16, two 2x8 and four 2x4. Any contact of the PXI-7931 can connect to other contacts, individually or in combination. The PXI-7931 matrix module simplifies the wiring and makes it easy to change the internal connection path. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7931, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
Product
2 Amp PXI Large Matrix Modules
BRIC™
-
Our 2 Amp PXI Large Matrix Modules use high-quality electromechanical relays to achieve their 2A switch rating. The BRIC structure allows the creation of large PXI matrices over multiple slots without the use of expensive external cables. The fully integrated programming interface represents the matrix as a single entity, easing user programming and reducing the likelihood of user errors.
-
Product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
Fault Insertion Unit
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
Product
PXI Precision Resistor Module 6-Channel, 3 to 2.97M
40-297-051
Programmable Resistor Module
A simple solution for applications requiring accurate simulation of resistive sensors. The series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI RTD Simulator Module, 16 Channel, PT100
40-263-201
Simulator
The 40-263-201 is a 16-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
High-Power PXI Switch Matrix Modules
-
These high-power PXI switch matrix modules provide higher current and power ratings than the high-density switch versions. These modules are designed for the switching of AC or DC loads or for controlling large relay or solenoid systems. The solid state relay matrices occupy two PXI slots and are suitable for automotive and aerospace test applications.
-
Product
PXI Multiplexer, Single 16-Channel, 4-Pole
40-630A-022-16/4
Multiplexer Module
The 40-630A-022-16/4 is a single 16-channel, 4-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI Potential Divider Module 24-Channel (no resistors fitted)
40-282-121
Programmable Resistor Module
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
Product
PXI Resistor Module 4-Channel 1R to 127R with SPDT
40-293-112
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Dual 44x4 Matrix, 1-Pole Switching
40-536-021
Matrix Switch Module
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109operations to give maximum switching confidence with long life and stable contact resistance.
-
Product
PXI 5A Power MUX, 1-Bank, 48-Channel
40-651-001
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel 4-bank. 11-channel 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
PXI Base Module
PA72
-
The PA72 platform is a platform of flexibility. It consists of a base board and one or two daughter boards. In daughter boards there is choice from several different generators, digitizers, filters, and Flexible Digital I/O modules. Also custom daughter boards can easily be created. This allows you to configure a data acquisition card exactly tailored to your needs. The PA72 concept provides a flexible and cost effective solution for medium and high end analog functions.
-
Product
PXI 10A Power MUX 8-Bank 4-Channel
40-661-001
Multiplexer Module
The 40-661 is a single pole PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
Product
8 Slot Embedded PXI Portable PC
-
The beltronic embedded PXI-Portable PC is built to be used in Military and industrial areas which call for this kind of robust and reliable system. The compact and very solid aluminum housing meets industrial and MIL-810 environmental requirements. The system complies to high EMC/EMI standards like MIL-461/704/1275. It operates on 110 to 230V AC or a 24VDC (optionaly).
-
Product
PXI High Density Multiplexer, 10-Bank, 8-Channel, 2-Pole
40-615A-004
Multiplexer Module
The 40-615A-004 is a 10-bank, 8-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXI Precision Resistor Module 9-Channel, 1.5 to 925
40-297-021
Programmable Resistor Module
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI 38 Channel 2 Amp Multiplexer Card
40-656-001
Multiplexer Module
A 38-channel multiplexer, 2-pole switching, suitable for switching signals to 2Amp, 220VDC/125VAC. It offers the highest switching density in its class for medium power/ voltage signals. Specifically designed for switching POTS, ISDN or xDSL telephony signals. Bandwidth for most configurations is typically >25MHz. It is paired with a very similar module, 40-655-001, a multi-banked multiplexer.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 16 Channel
41-761-003
Simulator
The 41-761-003 is a low voltage 16-channel output module ideal for simulating theoperation of a thermocouple, also available with 32, 24 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
Product
PXI 2 Amp MUX, Dual 16-Channel 2-Pole
40-635-006
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
