-
Product
Extender Boards
-
VECTOR Electronics and Technology, Inc.
Extender boards are designed to bring a circuit card completely out of a card cage or enclosure so that it can be tested or debugged. This provides access to both sides of the test board.
-
Product
PCI Express A/D Board
AD16-250 - Dual/Quad 16 bit, 250 MS/s
-
The AD16-250 series has two or four 250 MS/sec 16-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at over 1 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual and quad channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, providing up to four (4) times the effective memory depth.
-
Product
PC/104 Analog Output Board
104-AO12-4
-
The following functions are available in many configurations giving the user the ability to specify exactly what’s needed. Interrupts are individually or globally enabled or disabled via software. A status register is provided to determine the interrupt source.
-
Product
One Wire Communication Board
MS 1727
-
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
Product
VXI Register-based Interface Board
-
VXI Register Interface mates with user's PCB to form a B or C-size module.
-
Product
Pkt2-PCIe and Pkt2-AMC Boards
-
Provide front-end intelligent processing for DPI, IPsec and GTP acceleration, delivering a high-performance, secure, carrier-grade, packet processing for LTE, 3G and IMS networks.
-
Product
High Speed Communication Board
MS 1712
-
- 12 Channel RS422 Standard Communication interface- 4 Channel Configurable Manchester Bi-Phase Signal communications- 4MBPS configurable baud rate- VIRTEX4 FPGA based design- Hardware Frame formation- Hardware Data validation with START & END frame identification and Checksum calculation for RS422 communication- 1MB DPRAM for PCI interface- Separate set of FIFO's for Transmit and Receive channel- 16 Channels data recording through CF (Compact Flash Storage - Capacity up to 8Gbyte) up to 30min @ 2Mb/sec- Online download through USB interface- Driver interface for Windows2000/XP/VISTA and LINUX OS- 6U size cPCI Board- Hot Swap facility is provided for the live Insertion and removing of the board- 12 RS422 channels in front panel interface using two 25-pin D-Type connector
-
Product
LVDS To DVI-D Converter Board
AX93221
-
*Input supports 18/36/24/48-bit LVDS through 40-pin LVDS connector*Output supports DVI-D connector*Size: 60 x 50 mm*Applied for PICO821 and PICO822
-
Product
Electronical Load Board 3U CompactPCI (air cooled)
045-097
-
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
Product
PC/104-Plus DMP Vortex86DX3 Single Board Computer w/ Dual Ethernet
PPM-C412
-
WinSystems’ PPM-C412 single board computer (SBC) is a PC/104-Plus form factor SBC featuring the latest generation DMP® Vortex86DX3® SOC processor. Its small size, low power, rugged design, and extended operational temperature make it a great fit for industrial IoT applications and embedded systems in the industrial control, transportation, Mil/COTS, and energy markets. 1 GHz DMP Vortex86DX3 Processor (Dual core) CPU.
-
Product
16 Relay Output PCIe Board, 8 Isolated Digital Input Channels, 24V
APCIE-2200-16-8
-
8 electromechanical relays with change-over contacts The PCI-Express 16 relay board APCIe-2200-16-8 has 16 relay output channels and 8 isolated digital inputs, 24 V. 7 inputs are interruptible. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
Product
6U cPCI Multi-function I/O Boards
78C2
Multifunction I/O
NAI’s 78C2 is a 6U cPCI Multifunction I/O and Communication Board with six independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
Board-to-Board Connectors
-
Panasonic Industrial Devices Sales Company of America
Panasonic's Board-to-Board Connectors are ideal for low profile applications. These board-to-board connectors range from 0.35mm pitch to 0.5mm pitch with various mated heights.
-
Product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for two M.2 or NGSFF (NF1) PCIe SSD Modules
SKU-086-32e
-
This Squid PCIe Carrier board can support up to two M.2 or NGSFF (NF1) PCIe SSD (solid state drive) modules, with M-key. Supported module dimensions are 2230, 2242, 2260,2280 or 22110 in length, and a width of up to 32 mm. SSD modules of any capacity may be used, from any vendor, and in any combination.
-
Product
PXI FPGA Board
PXIe-8316-DSP
-
The PXIe-8316-DSP FPGA board is a user programmable hardware platform with an 8-lane Gen3 PXI Express (PXIe) interface. It includes four QSFP ports (16 lanes) to support High Speed Serial (HSS) connections.
-
Product
6U Processor Board
VP62105
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP62105 supports up to 3615QE, an Intel® 4-core processor. The 3rd generation Intel® Core™ i3/i5/i7 processors have a completely new microarchitecture, enabling small-sized designs to be created with unmatched computing power, graphics performance and energy efficiency on a small footprint.VP62105 provides 4 Serial RapidIO (SRIO) x4 links for VPX Data Plane communication, 2 PCI express x8 channel for VPX Expansion Plane communication and 4 Gigabit Ethernet for VPX Control Plane communication. The rich data interchange options enable potential customers a much easier integration path for box level or system level solution designs.
-
Product
Configurable 6U CPCI Multifunction I/O Boards
Multifunction I/O
Optimized to deliver unusually high-function density, high resolution / accuracy and low power consumption for rugged defense, commercial aerospace, and industrial applications, NAI’s intelligent 6U CompactPCI cards can often operate as standalone systems, eliminating the need for a Single Board Computer (SBC), operating system and associated software royalty costs.
-
Product
Advanced Programmable IO Board
MS 1508
-
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
Product
Performance Board For LSI Tester
-
Place inner layer GND plane all over. Impedance control of signal line and crosstalk prevention, etc. contribute to improvement of characteristics in various ways.
-
Product
3U VPX Board
VP32004
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP32004 is a high-performance PC-based 3U VPX processor board developed by Linkedhope®. It supports 3rd Gen Intel Core series processor and Intel QM77 chipset. It supports up to 16GB of on-board DDR3 ECC memory and supports mSATA SSD. In order to ensure that VP32004 works stably in a strong shock and vibration environment. VP32004 provides rich I/O interface, including 2x SATA III channels, 2x 1000 Base-BX/T, 1x RS232 front debug serial port, 3x RS232/422/485 interfaces (BIOS configurable), 4x USB2.0 interface, 1x USB3.0 interface, 1x Mini-DisplayPort display interface, 1x rear VGA display interface, 1x PS/2 interface.The board provides a flexible PCIe bus interface to the backplane that supports multiple configurations and can be configured as 1 x8, 2 x4, 4 x2 PCIe. This feature makes it suitable for both distributed and centralized switching systems.
-
Product
Isolated Programmable Multifunction Counter Board, LACQUERED
APCI-1710-LAC
-
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmable Each of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
Product
Acroname MTM Power Development Board
-
HIGH POWER. HIGH CURRENT. The MTM Power Development Board allows high power and high current connections to quickly deploy MTM testers.
-
Product
GPIB to Relay Interface Boards
Model 4864 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel. • 114521-12 Board provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as for the 114521-11 Board. * 114521-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as for the 114521-11 Board.
-
Product
MIL-STD-1553 Two-Channel PMC Board
BRD1553PMC-STD-2
-
The PMC HyperBoard is a multi-standard PCI Mezzanine Card that contains two channels of MIL-STD-1553 communication. The board is compatible with MIL-STD-1553B and MIL-STD-1760. Each channel can be configured independently to work with H009 and WB-194 in conjunction with MIL-STD-1553.
-
Product
I/O Board With Two COM, Four USB 3.0, VGA And Audio For PICO312, PICO313, PICO511, PICO512
AX93A00
-
*Specification: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 3.0, 1 x VGA, 1 x Audio (MIC-in/Line-out), 1 x Power-on, 1 x Reset, 2 x LED*Dimensions: 118 x 40 mm*Compliant product: PICO312, PICO313, PICO511, PICO512
-
Product
Digital Input Board, 32 Isolated Channels, 24V
APCI-1032
-
32 digital inputs, 24 V or 5 V, incl. 16 interruptible inputs Optical isolation 1000 V Input filters Protection against pole reversal
-
Product
3U OpenVPX High Density Multifunction I/O Board
68CB6
Multifunction I/O
The 68CB6 is a Configurable Open Systems Architecture™ (COSA®) 3U OpenVPX™ board that is preconfigured with 10 different “inboard” I/O, measurement and communication functions. This Combination-function Board (CB) provides a full suite of some of the most common & useful function interfaces supporting many different applications. The 68CB6 features a wide but dedicated selection of functions: Standard Functionality Discrete I/O (DT1); Successive Approximation Register (SAR) ±100 V Analog-to-Digital (AD); Isolated High Voltage Analog-to-Digital (ADF); ±10 V Digital-to-Analog (DA); Thermocouple (TC1) or Resistance Temperature Detector (RT1); Full-bridge Strain Gauge (SG1); Transmission/gear box Chip Detection and Fuzz Burn (CD1); LVDT-to-Digital linear (LD6) displacement (position) measurement, AC Reference Source output (AC2); CAN bus communication (CB8). The 68CB6 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for external intermediate circuit considerations such as pull-up resistors or mechanical configuration jumpers. Inboard functions are software controlled and memory addressed, accessed in similar COSA® modular fashion to maintain seamless common NAI Software Support Kit & API/library structures.
-
Product
LGA 6096 AMD® EPYC™ 9004 ATX Server Board with 6 x DDR5, 5 x PCIe x16 + 2 x PCIe x8, 9 x SATA3, 7 x USB 3.2 (Gen1), Dual 10GbE, and IPMI
Part No. ASMB-831
-
- LGA 6096 (Socket SP5) ATX server board with AMD® EPYC™ 9004 processor- DDR5 4800 MHz RDIMM up to 384GB (6 DIMMs)- Five PCIe x16 (Gen5) and two PCIe x8 (Gen5) for four double-deck cards- Intel® X710-AT2 dual 10GbE ports- Nine SATA3 and seven USB 3.2 (Gen1) ports- Two M.2 2280/22110 (SATA / PCIe compatible)- 0 ~ 60 °C/ 32 ~ 140 °F ambient operating temperature range
-
Product
Combination Board Tester
V250 / V250PXI
-
Qmax Test Technologies Pvt. Ltd.
V250 / V250PXI is designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
Product
Serial I/O Boards
-
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
