-
Product
NI-9474, 30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
779003-01
Digital Module
30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9474 works with industrial logic levels and signals to directly connect to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 5 V to 30 V, features transient overvoltage protection between the output channels and earth ground, and has a LED that indicates the status. The NI‑9474 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization when installed in a CompactDAQ chassis.
-
Product
4-CH 16-Bit 10/40 MS/s PCI Digitizers with 512 MB Memory
PCI-9816/9846
Digitizer
The ADLINK PCI-9816/9846 are 10MS/s, 40MS/s sampling 16-bit 4-CH digitizers designed for digitizing high frequency and wide dynamic range signals with an input frequency up to 20 MHz. The analog input range can be programmed via software to ±1 V or ±0.2 V and ±5 V or ±1 V. With a deep onboard acquisition memory up to 512 MB, the PCI-9816/PCI-9846 are not limited by the data transfer rate of the PCI bus to enable the recording of waveforms for extended periods of time.
-
Product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 400 MS/s on 4 Channels, 4 Single-Ended Inputs
DN2.448-04
Digitizer
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PCIe-5764, 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785961-01
FlexRio Digitizer
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Tester
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
Product
PXIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4X.2220-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
NI-9478, 50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module
779940-01
Digital Module
50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module - The NI‑9478 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. The NI‑9478 features programmable current limits, which provide customizable system protection that is ideal for solenoid and valve control applications. Each channel is compatible with signals from 5 V to 50 V and features isolation from channel‑to‑earth ground.
-
Product
PXIe 8 Bit High Speed DIgitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
M4X.2211-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXI Semi-Dynamic Digital I/O Module, 64-Channel
40-419-001
Digital I/O
The 40-419-001 is a 64-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
Keysight Multifunction Module with 32-bit DIO, 2-ch D/A and Totalizer for 34980A
34952A
Digital / Analog Converter
The Keysight 34952A module for the 34980A Multifunction Switch/Measure Unit allows great flexibility for a variety of sense and control applications.It combines the following on a single earth-referenced module:
-
Product
48 Optocoupled Digital Inputs
YAV90321
Digital I/O
Input Voltage 3…42Vdc Isolated Inputs / Control >1000Vdc CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
Product
PXIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4X.2230-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PCI-6519, 32-Channel, ±30 V, 16 Sink/Source Inputs, 16 Sink Outputs, Bank-Isolated Digital I/O Device
779085-01
Digital I/O
The PCI-6519 is an industrial digital I/O interface, with two banks optically isolated channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6519 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6519 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
PXIe-6536, 32-Channel, 25 MHz, 100 MB/s PXI Digital I/O Module
779988-01
Digital I/O
32-Channel, 25 MHz, 100 MB/s PXI Digital I/O Module—The PXIe‑6536 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
PXI-6521, 16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs, Isolated PXI Digital I/O Module
779313-01
Digital I/O
16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs, Isolated PXI Digital I/O Module—The PXI‑6521 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. For added safety, the PXI‑6521 requires a keyed connector. If a computer or application fault occurs, the PXI‑6521 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
-
Product
Dynamically Controlled, High Voltage Digital I/O PXI Card With Pin Electronics
GX5055
Digital I/O
The GX5055 represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the GX5050, the GX5055 offers high performance pin electronics and an enhanced timing generator in a compact, 6U PXI form factor.
-
Product
Linear IC Tester
570A
-
The Model 570A Analog IC Tester's built-in test library includes all common Analog ICs including op-amps, comparators, voltage regulators, voltage references, analog switches & multiplexes, opto-isolators & couplers, and audio ICs.
-
Product
NI-6583, 200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO
781320-02
Digital I/O Adapter
200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO—The NI-6583 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 32 single-ended and 16 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6583 can sample digital waveforms at up to 200 MHz. It includes support for selectable single-ended voltages from 1.2 to 3.3 Volts with 10 bit resolution and common LVDS voltages.
-
Product
Digital Logic ICs
-
Renesas' general-purpose logic devices support the information equipment and computer fields, which demand small size and high performance. With a variety of power supply voltages, functions, and capabilities, these logic devices provide strong support for specialized applications such as bus switching, level conversion, and clock-related applications.
-
Product
Industry Pack Carriers and Digital I/O
CPCI-IPC
Digital I/O
The CPCI-IPC module provides a 3U high performance flexible I/O scheme, that supports industry standard Industry Packs™. For application requiring low cost, high density I/O or unique combinations, the CPCI-IPC is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSP via the CompactPCI bus. A very low cost, non-intelligent version is also available, CPCI-SIP.
-
Product
Digital Management Software
EdgeGO
Digital Management Software
EdgeGO® is a robust software platform for remote device management in edge computing environments. It prioritizes quick deployment and user-friendly operation while ensuring scalability and security.
-
Product
Digital Multimeters
T3DMM Series
Digital Multimeter
Teledyne Test Tools new T3DMM series are dual display digital desktop multimeters that provide a rich and powerful feature set. The design is easy-to-use from the front-panel and computer-based control via USB or LAN. Each model is equipped with a 4.3 inch TFT-LCD true color screen with 480 * 272 resolution for easy viewing. The T3DMM series also features numerical data display, histograms, trend charts, bar charts and statistics, in addition to the built-in arithmetic functions including Measurement statistics.
-
Product
PCIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4I.2220-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PCI-6511, 64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated Digital I/O Device
778966-01
Digital I/O
The PCI-6511 is an industrial digital input interface, with eight banks of isolated channels. If a computer or application fault occurs, the PCI-6511 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
NI-6585, 200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO
781071-01
Digital I/O Adapter
200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO—The NI-6585 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 32 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6585 can operate at up to 200 MHz clock rates and includes support for common LVDS voltages.
-
Product
Digital Multimeters
Digital Multimeter
Digital Multimeters measure voltage, resistance, current, capacitance, inductance, and temperature. Some models also have an isolated digitizer mode. Use these products to test consumer electronics, fuel cells, aerospace production, and more.
-
Product
Digitizer with two 125 MS/s, 14-Bit Channels, Recommended for VXI Systems
6084-2105
Digitizer
The Astronics 6084-2105 digitizer includes two 125MS/s, 14-bit digitizer channels and is recommended for VXI systems that need either improved accuracy or replacement of an obsolete instrument. Wide dynamic sampling, a powerful acquisition engine, and excellent AC/DC performance ensure an upgrade for your VXI system that will preserve your legacy investment for years to come.Key features include:Dual 14-bit digitizers for SE or DIFF operation at sample rates up to 125 MS/sDC accuracy of 0.15% ± 800 µV on low voltage rangesSFDR 80 dB at 1 MHz Wide input ranges from 0.25 Vpk to 256 VpkPerformance upgrade or replacement for existing VXI applications Pre- and post-triggering availableWaveform storage of 32 M samples per channel
-
Product
PXI Digital Multimeter, 6 digit, Enhanced Performance
M9183A
Digital Multimeter
The Keysight M9183A is a 6 digit PXI digital multimeter that measures common parameters such as DCV, DCI, ACV, ACI, 2- and 4-wire resistance, frequency, capacitance, and temperature. It offers40 ppm basic DCV measurement accuracy, excellent noise rejection, and handles inputs of up to 300 V.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 16 Channels, 16 Single-Ended Inputs
DN6.447-16
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PXIe-6569, PXI FlexRIO Digital I/O Module
787281-01
Digital I/O
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
