Signaling
The use of signals for controlling communications. (atis.org)
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
Product
Signal / High Power, Module, ITA, TriPaddle, iCon Series, 4/4 Position
510161124
ITA Module
Primary mating module 510160124. (May mate with other Receiver modules, as well.)
-
Product
DS Sensor
Z-Gard DS Sensor
-
The Z-Gard DS Sensor is designed to detect the presence of carbon monoxide and nitrogen dioxide gases in parking garages, vehicle storage areas or wherever else these two toxic gases could be found. These sensors employ electrochemical sensors which generate a representative output signal proportional to the calibrated operating range.
-
Product
Analoge Sound Level Meter
Model KM-20/ YF-20
-
Kusam Electrical Industries Limited
One-handed simple, easy to operate. Inbuilt reference signal. Inbuilt battery test. Quickly, accurately sures sound level. Compressed scales minimise range switching. An internal reference signal is available for checking the meter’s operation. Calibration Check. Microphone with Capacitance Microphone.
-
Product
HandyScope HS5 + SureConnect: 200 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 20MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-220XMS-W5
-
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 200 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
Product
PXIe-4322, 16-Bit, 8-Channel, 250 kS/s Ch-Ch Isolated PXIe Analog Output Module
782878-01
Analog Output Module
16-Bit, 8-Channel, 250 kS/s Ch-Ch Isolated PXIe Analog Output Module—The PXIe‑4322 is a channel‑to‑channel isolated analog output module with integrated signal conditioning. The device provides accurate, simultaneous dynamic voltage and current outputs. By combining signal conditioning and D/A converters on the same device, the PXIe‑4322 isolated analog output module delivers a smaller footprint and higher measurement performance. In current mode, the module operates in all four quadrants, so you can both sink and source current. Isolation and higher voltage and current outputs make this module ideal for automotive applications.
-
Product
56 Channel TTL I/O FPGA PXI Card
GX3756 Series
FPGA PXI Card
The GX3756 is a user configurable, FPGA-based, 3U PXI card which offers 56, TTL I/O signals. The module consists of a daughter card and the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA.
-
Product
9GS/s 8Bit, 4GS Mem 4CH 16 Markers AWG
P9084D
Waveform Generator
The Proteus P9084D, is a 9GS/s, four channel arbitrary waveform generator packaged in a 4U, half 19” dedicated chassis, offering technologically advanced options and configurations that integrate the ability to transmit, receive and perform digital signal processing all in a single instrument. The P9084D offers industry leading performance Including an innovative task oriented programming, real time data streaming, fast feedback loop for environment dependent waveform generation and user customizable FPGA for application specific solutions.
-
Product
PXI 5 Ch. Differential Hi Voltage Attenuator
41-661-001
Attenuator
High voltage attenuators designed to reduce the high output voltages commonly generated by some types of sensors. This is in order to produce manageable signal levels that can be acquired by typical data acquisition devices in a PXI system.
-
Product
FieldFox C Handheld Microwave Analyzer, 6.5 GHz
N9914C
-
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
Product
Clock Drivers
-
Multiple timing signals ("clocks") are required by CCDs, IR FPAs, and some CMOS image sensors to transport electrical charge across the array to a sense amplifier for conversion into image data. Pulse Instruments offers a line of "clock drivers" for generating these timing signals. The parameters of these clocks (clock rate, pulse width, pulse amplitude, rise- and fall-times, etc.) greatly influence the behavior and performance of the imaging device. Our products take logic-level inputs from a pattern generator and allow the user to adjust the output parameters to suit their device and testing requirements. Clocks can be "tweaked" in real-time to determine optimal operating parameters for a particular device, or else programmed in accordance with a test plan for automated production test.
-
Product
PXI-6229, 32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO, PXI Hybrid, Multifunction I/O Module
779630-01
Multifunction I/O
32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXI‑6229 offers analog I/O, correlated digital I/O, two 32‑bit counter/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
3-Slot Data Acquisition Mainframe With GPIB And Three 20-Channel Multiplexer Modules
DAQ973MB
Mainframe
The DAQ973MB Better Multiplexer Bundle offer includes a DAQ973A three-slot data acquisition mainframe and three 20-channel DAQM901A multiplexer modules. This bundle provides the following:3-slot mainframe with USB, LAN, and GPIB6.5-digit (22-bit) internal DMM60 channels of multiplexer switches6 channels of dedicated current measurements2- and 4-wire scanning300 V switching80 channels/s scanningbuilt-in thermocouple reference junctionbuilt-in signal conditioning to measure thermocouples, RTDs and thermistors, AC / DC volts and current; resistance, frequency / period, diode test, and capacitance
-
Product
PXI/PXIe High Density 2A Multiplexer, 5-Bank, 8-Channel, 3-Pole
42-614D-021
Multiplexer Module
The 40-614D-021 (PXI) and 42-614D-021 (PXIe) 5-bank, 8-channel, 3-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
VPX/open VPX C-Frame 5 Slot 6U
-
Our 2nd Generation C-Frame offers the next level of flexibility in VPX development platforms. Not only can the customer exchange the type of card guides (convection, conduction, AFT) in a blink of an eye but now also the signal backplane. Thanks to Bi=/=Plane®technology, power and signal parts of a VPX backplane are separate PCB assemblies. This enables uncompromised signal quality along with faster turn around for the design of custom profiles.
-
Product
3.4 MP Autofocus (Liquid Lens) Low Light Camera Module
e-CAM31_MI0330_MOD
-
e-CAM31_MI0330_MOD is a high performance, small form factor, 3.4 MP Autofocus Low Light Camera Module with Liquid Lens. It is based on AR0330 CMOS Image sensor from ON Semiconductor®. This Autofocus Liquid Lens Camera Module has slave mode for precise frame-rate control and for synchronizing two sensors. e-CAM31_MI0330_MOD – Liquid lens camera module has superior low light performance. It supports Full HD @ 60fps for maximum video performance. It also has a support for external mechanical shutter and an on-chip phase-locked loop (PLL) oscillator. The dedicated ISP performs the entire Auto functions like auto white balance, auto exposure control in addition to complete image signal processing pipeline.
-
Product
LXI Microwave Multiplexer, SP6T, 7-Bank, 67GHz, 50Ω, SMA-1.85
60-800-807
Microwave Multiplexer
Our 60-800-807 is a 7 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
TINYig Oscillators
-
The smallest available oscillator in the industry, Teledyne Microwave's TINYIG is an ultra-low phase noise YIG-tuned oscillator (YTO) that provides superior phase noise frequency up to 20 GHz. Uniquely designed to be RoHS compliant, these YIG TO-8 oscillators exploit the principle of magnetic resonance to generate a clean, low phase noise microwave signal over broad tuning ranges. It can greatly simplify system designs, thus reducing costs, eliminating the need for extra components, and reducing the risk of malfunctions of complicated electronic connections and operations.
-
Product
LXI Single 32 Channel Fiber Multiplexer FC/APC, Single-Mode
60-850-014
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI Dual 2 x 2 Insert/Bypass Switch FC/APC
40-860-022
-
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
YAGI
-
RF Solutions offers a comprehensive selection of high-performance Yagi antennas, sourced from leading manufacturers and available for immediate dispatch. These directional antennas are engineered for applications requiring focused signal transmission and reception, making them ideal for long-range communication, telemetry, and remote monitoring systems.
-
Product
Radar Target Generator
Series 1100
-
The Eastern OptX Series 1100 Radar Target Simulator is a true propagation path replicator. The Series 1100 receives the signal transmitted from a radar system and adds the round-trip propagation delay associated with the target distance. That signal is then output to the radar receiver. The radar I/O may be connected directly to the Series 1100 or detected and transmitted using user specified antenna. For a moving target the system will add the appropriate Doppler shift associated with the target speed and radar frequency. The Series 1100 is broad band with ranges up to 40 GHz and with a dynamic range of over 100 dB.
-
Product
Power Dividers
-
Powers plitters can divide one signal into two or N way equal or non-equal energy, in reverse,they are also used as combiners by combining multiple signal into one. They are mainly used in feed network in antenna array, mixer and balanced amplifier, finish the work of distributing, combining and measuring power, isolating signal sources and measuring swept reflected coefficient etc.
-
Product
LXI WTB Terminator, 100 ohm
60-983-001
Terminator
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 9-Bank 26.5GHz SMA
60-802-309
Multiplexer Module
The 60-802-309 is a 4-channel, 9-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
O/E Converter
TIA-3000
-
The TIA-3000 is an instrument for the laboratory or for field use. This amplified optical-electrical converter can be used with a wide range of oscilloscopes and digitisers to provide the utility of a convenient, easy to use fibre optic probe. Energising the unit, the optical signal presented to it is faithfully reproduced on the CRT of the oscilloscope or digitiser.
-
Product
PXI Quad 2x2 Fibre Optic Mux MU
40-860-342
-
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 75Ω, MCX
40-835A-101
Multiplexer Module
The 40-835A-101 (PXI) and 42-835A-101 (PXIe) are single 75 Ohm 16-channel RF multiplexers in a single slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40/42-835A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
3.5" Single Board Computer With Intel® Core™ Ultra Processors
SBC35-MTL
Single Board Computer
ADLINK SBC35-MTL, a compact 3.5" Single Board Computer equipped with Intel® Core™ Ultra Processors for efficient, high-performance computing. It features an integrated NPU to boost AI processing capabilities and includes a reserved MIPI-CSI signal pathway for easy camera integration, making it ideal for real-time and vision-based applications. The SBC35-MTL is designed to meet the needs of modern embedded systems, delivering cutting-edge performance in a compact form factor
-
Product
SparkFun Triple Axis Accelerometer Breakout
ADXL377
-
The ADXL377 is a small, thin, low power, complete 3-axis accelerometer with signal conditioned analog voltage outputs that has a full-scale range of ±200g for measuring more extreme changes in motion, shock or vibration. This board has broken out all the pins you’ll need to get the necessary data from the accelerometers. The breakout is perfect for applications like concussion and head trauma detection or high force event detection.
-
Product
Waveform Generation Toolbox for Wideband Signal Simulation
N7509A
-
The Waveform Generation Tool provides a simplified interface for baseband modulation of Keysight's wide bandwidth signal simulation solutions, for signals with up to 1 GHz RF bandwidth. Even the most complex signals are defined and implemented easily through the software interface. Signals can be defined through basic parameter entry or from files created in MATLAB or other engineering environments. For each selection in the main menu, a subsequent screen appears, enabling the user to enter the parameters required to define the waveform and invoke the built-in calibration routines. A display on each sub-panel shows the ideal frequency domain waveform calculated from entered parameters. A simulation mode is provided to enable development and operation without connection to the instrument hardware.
