Battery Internal Resistance
-
Product
Battery Test Software
-
Landt Battery Test Systems use different programs for data acquiring and data process. The acquiring software comes with a very user-friendly interface, which allows new users to operate with minimal training. Data process software shows different kinds of plots (Voltage vs. Capacity, Capacity vs. Cycle Number, Efficiency, etc.), which can be easily exported.
-
Product
6/12/24/36V Conductance Battery Tester
MBT300
-
Tests 6/12/24V lead acid batteries individually or in parallel and series battery packs. Displays battery or battery pack condition as % available capacity, rated capacity (CCAs), state of charge voltage, and good or replace status. Tests 6/12/24/36V starter and charging systems including starter draw, alternator and regulator output (loaded/unloaded), and diode ripple.
-
Product
Battery Discharger & Capacity Tester
IDCE-2415CT
-
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-2415CT Battery Discharger & Capacity Tester
-
Product
High Resistance Neutral Grounding Devices
-
HRG systems limit the fault current by placing high resistance between neutral point of transformer (or generator) and ground. As it is not possible to locate the fault point in delta connected systems, an artificial neutral point is created and delta connected system can be grounded. This allows a fault current of a few amperes thus locating the fault point gets easy. When the neutral point is grounded thru high resistance, both continuity of operation is provided during fault condition and sufficient current (typically between 2 A and 10 A) flow is provided for ease of locating the fault point.
-
Product
4-Wire Resistive Type Single-Touch Module
ETM-RES05C
-
Resistive touch technology, supports 4-wire Touch Screen, Supports USB and RS-232 Interface, Resolution support to 2048 x 2048, High Reliability and Fast Conversion Time.
-
Product
Emergency Battery Power Supply Test Fixture
TA-61
-
This test fixture provides an interface to test and chargethe Radiant type RPS1-B Emergency Lighting power supply. The panel includes the switching required asdescribed in the CMM along with an analog currentmeter for monitoring the charging current. This panelprovides simple testing for the corporate flight departmentor DOM.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 1 kV Isolation
41-752A-111
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Regular Battery Tester Models
-
The following are regular battery tester models for single-cell tests (coin cell/half cell/pouch cell/cylindrical cell, CT2001 & CT3001 Models) and supercapacitor test.
-
Product
Servo Computer Battery Crush Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Servo Computer Battery Crush Tester simulates the situation in which various types of lithium batteries are squeezed during use. Artificially present different conditions that may occur when the battery is squeezed.
-
Product
Transformer Resistance Testing
-
Transformer insulation resistance deterioration is one of the most common causes of transformer failure: a failing transformer is a costly replacement in an electrical system with the potential for a long downtime. If you fail to maintain your transformer with regular insulation resistance testing (as can be carried out by the Megger Transformer Ohmmeter (MTO) series of transformer test equipment) then it’s likely to fail before reaching its maximum operating life.
-
Product
USB Graphics Adapter, Internal Mount, DB-15 connector
DB-UVGA16
-
- Mounts in DB9 cutout on chassis or in PCI slot- Uses internal USB pin header- Display resolutions up to: 1600 x 1200 (4:3), 1680 x 1050 (16:10)- Supports multiple display modes: Primary, Extended, Mirr
-
Product
Battery Simulator SoftPanel
A170202
-
For the products developed to connect batteries for use, if the battery is not ready or unable to be provided due to high cost, the 17020 battery simulator can be used to confirming the product functions during development. The applications of battery simulator include motor drives within the car system, OBC, D-D convertor or charger within the CSS system and products of DC bus, etc.
-
Product
Car Battery Checker
BT-300
-
Konstar Electric Industrial Co., Ltd
Battery tester can test the car battery whether is ok, if the battery is bad or need charge or bad, the tester will give you the right check result, then can do the right plan for the battery before work.
-
Product
Battery Pack/Module Test Solution
-
Regenerative battery energy dischargeEnergy savingEnvironment protectionLow heat generateChannels paralleled for higher currentsCharge / discharge mode (CC, CV, CP) Constant current Constant voltage Constant powerDriving cycle simulationHigh precision measurement accuracyFast current conversionSmooth current without over shootTesting data analysis functionData recovery protection (after power failure)Independent protection of multi-channelBMS data recordingThermal chamber control integration
-
-
Product
Murata Watch Battery
-
World's first mercury-free silver watch battery innovator, highly recognized as No. 1 market share manufacturer by major watch brands
-
Product
Hand Cranked Analog Insulation Resistance Tester
IRT20
-
UEi Test & Measurement Instruments
The IRT20 is a Hand-cranked Insulation Resistance Tester. With a insulation resistance range of 0.1 to 1000MΩ, 250, 500 and 1000V output ranges and accurate to with in one division. It is in a sealed, water resistant, rugged metal housing and is backed by a 1-Year limited warranty.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, 1 kV Isolation
41-752A-102
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Battery PACK (500v-1000v)Test System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
PACK test equipment adopts sinexcel, firstly adopts three-level AC scheme, and the detection process supports multi-gear switching. The device integrates voltage, temperature, pressure and other auxiliary channels, and CAN also integrate various communication protocols such as temperature box, water cooler, mainstream CAN CANFD 485, etc. It supports a variety of practical and innovative functions such as data one-click automatic export, which meets all aspects of PACK battery electrical performance testing.
-
Product
Battery Testing
-
With the increasing dependency of back up systems on battery strings, and the escalating cost of replacing batteries, instrumentation and software systems that can measure, trend and manage the life-cycle of cells is a cost effective option.
-
Product
Winding Resistance Meter 50Amps, 3 Channels
WR50-13
-
Raytech Digital Winding Resistance meter WR50-13 is the enhanced version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
SOC Battery Tester
-
This sophisticated battery test equipment allows the battery tester to exercise and explore the battery’s internal profile and produce a true state of charge revealing the batteries true AHR capacity and ability to perform under load.
-
Product
Battery Tester
6470 BT
-
Standard Electric Works Co., Ltd
2000 counts. DC Voltage measurement. 4-wire resistance measurement. Data hold function. Low battery indication. 9V DC power supply. Measure battery types: Li-ion, Ni-Cd, Ni-MH. Simple operation. Lead resistance and contact resistance eliminated.
-
Product
Resistance Meter
RM3542A
-
High-speed resistance meter ideal for automated lines; compatible with super-small electronic components• Testing source: DC• Fastest measurement time: 0.9 ms• Minimum integration time: 0.1 ms• Finest resolution: 0.1 μΩ
-
Product
3 Wire (Analogue) Earth Resistance Tester
2705 ER
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Battery check function.● Calibration performed with supplied test leads.
-
Product
Electronic Store Of Resistances
PS8
-
The module is intended for use as part of information measuring systems based on the VXI bus for software setting of resistance values with a given step along three independent channels.
-
-
Product
1μΩ-4kΩ AC Milliohmmeter Low Resistance Tester
TH2521
-
Shenzhen Chuangxin Instruments Co., Ltd.
TH2521 AC Milliohmmeter is a high-performance and intelligent tester widely used to test contact resistance, internal resistance and battery voltage. The application of constant current source with 1kHz frequency can greatly eliminate the potential error caused by thermoelectricity on DUT. This meter has the function to automatically detect contact failures on test cable. At the range of 30mΩ, basic R resolution can reach 1μΩ. It is applicable for transformer, inductance coil copper resistance, relay contact resistance, switch, connector contact resistance, wire resistance, PCB line and via reistance dan metal defect detection, etc. In the mean time, signals, such as HIGH, LOW, PASS, can be output through HANDLER interface, thus it is very convenient to be used in automatic production line.
-
Product
Ground Resistance
-
Provide accurate and reliable measurements of both ground resistance and soil resistivity for installation and troubleshooting.
-
Product
Terminal High Resistance
-
Terminal High Resistance Standards that can be rack or bench mounted. The 6636 Series provides a set of customer chosen precision resistance standards enclosed in a temperature controlled chamber.
