Temperature Calibrators
Measure and source/simulate RTDs, thermocouples, Volts, and ohms to test and calibrate temperature sensors and transmitters.
-
Product
High Temperature Pitot Probe Protective Cover
-
This Pitot Probe Cover developed by Nav-Aids Ltd. withstands temperature to 950 degrees F when installed on the pitot tube.With the Nav-Aids Ltd. High Temperature Pitot Probe Cover installed on the pitot tube, and the heat inadvertently activated, there will be : No melting of material No significant residue on the pitot tube No filling of static or drain holes No need to change a pitot probe No cause for aircraft dispatch delay
-
Product
Logger version conductivity and temperature sensor
INFINITY-CT A7CT-USB
-
Infinity-CT is an autonomously deployable data logger for temperature and salinity measurements. The conductivity sensor has a design of 7-electrode. The small-sized instrument (Φ54mm x 255mm, 0.7kg in air) can be deployed and integrated virtually anywhere. The instrument has two depth rating versions: shallow water (200m, A7CT2-USB) and deep water (2,000m, A7CT-USB).
-
Product
Temperature and Humidity Regulator
H3331-2
-
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
Product
TI HDC1080 Humidity and Temperature Sensor Breakout Board
SEN-37001
-
Breakout board for the Texas Instruments HDC1080. This sensor is an extremely accurate temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT2x series, and improves upon the success of the HDC1050. In addition, the HDC1080 has a wide input voltage range of 3V-5V and includes temperature and airflow cutouts as recommended for the best operation. Finally, in the case of environmental changes that could cause light condensation, the HDC1080 has a built-in heater to burn off any condensate. Example code (Arduino platform) is available below.
-
Product
Portable Vibration Calibrator
AT-2040
-
With AT-2040 you will find the features required for your application without having to install cumbersome and expensive addons. AT-2040 features a full-automatic sensitivity test mode, sensor simulation, power supply output for sensors that require voltage such as the 7310 and 991V aviation sensors, a built-in sensor charge amplifier for both single-ended and differential charge accelerometers, and a custom sensor input that can be configured to fit most accelerometers with a one to one cable.
-
Product
Temperature and Humidity Transmitter
T3419-2
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
PRO+ 2-in-1 pH and Temperature Meter
MW102
-
The Milwaukee MW102 PRO+ pH meter has won fans around the world with its reliable, fast and simple operation as well as its toughness. Accurate to ± 0.02 pH with automatic temperature compensation. Ideal for use by brewers, wine makers, growers and other users with challenging pH measurement needs.
-
Product
Handheld 2-D EM current meter with temperature and depth sensor
AEM213-D
-
AEM213-D electro-magnetic current meter with a display unit can provide the 2-D current speeds in real time. The instrument has a depth and a temperature sensor as well as the current sensor, enabling reliable current measurements at the desired depths. The compact and light-weight unit is easily portable, allowing you to use the instrument in a variety of situations.
-
Product
Temperature Data Logger
TG-4080
-
The Tinytag Transit 2 logger, TG-4080, is a practical, robust, lightweight and cost effective temperature recorder ideal for monitoring goods in transit such as foods, pharmaceuticals and other temperature-sensitive products.
-
Product
PicoLite Limited Use USB Temperature Data Logger
-
The compact and easy-to-use PicoLite USB data logger provides an ideal solution for temperature monitoring throughout the cold chain transportation network. Combined with the weboomerang™ feature, an innovative solution for automatically emailing trip reports back to the shipper, the PicoLite successfully meets the challenge of combining low cost, functionality and reliability for limited use, low cost data logging.
-
Product
Class 1 Sound Level Calibrator
HD2020
-
The HD2020 sound level calibrator is a portable, battery operated sound source, suitable for sound level meters (portable and laboratory) and acoustic stations.
-
Product
Temperature and Humidity Regulator
H3021-4
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Mercury Argon Calibration Source
HG-1
-
The compact, low-cost HG-1 Mercury Argon Calibration Source is a spectral wavelength calibration source for UV-VIS-Shortwave NIR spectrophotometric systems.
-
Product
MCB Temperature Rise and Power Loss Test Bench
-
The SCR Elektroniks 3 station MCB Temperature Rise and Power Loss Test Bench is economically designed to verify temperature rise and measure power loss as per clause 9.8 of IEC 60898 with the circuit designed to follow test procedure as per Cl 9.8.2. The temperature rise is measured in accordance with Cl 9.8.3 and 9.8.4 while power loss is measured and verified as per Table 15 of Cl 9.8.5.
-
Product
Current Probe Calibration Fixtures
-
Calibration fixtures are used for calibration of Coupling Loss/Transfer Impedance of current probes and BCI probes, as well as for the calibration of test levels for conducted immunity/susceptibility tests using BCI probes.
-
Product
Temperature Transmitters
-
Temperature Transmitters for every application. Datexel manufactures both Head Mount Temperature Transmitters (Hockey Puck Temperature Transmitters) and Din Rail Mount Temperature Transmitters. PC Programmable, IS Temperature Transmitters, Isolated Temperature Transmitters.
-
Product
Infrared Temperature Converter
TF Series
-
TF series, infrared temperature converters provide non-cotact measurement to caculate the surface temperature of the objects by measuring the energy of infrared light. So It is convenient to measure the surface temperature of especially moving objects. Its stainless case with integrated design combining sensors, optical system, and electronic circuits. It is easy to install by connecting the screw with other devices, and TF can be used in a wide range of industries.
-
Product
MTB Calibration Adapter
2450-CAL-30
-
The MTB Calibration Adapter (Catalog No. 2450-CAL-30)is a socket adapter that’s designed to bring phase A, B, and C current and potentials of a TESCO Multi-Position Test Board to an external RD-30 reference standard for calibration of the Test Board.
-
Product
Floor Temperature Probe
TP3207P
-
Temperature probe, Pt100 sensor, for measuring floor temperature (diameter Ø 70 mm, height 30 mm). Cable length 2 metres. Equipped with SICRAM module.
-
Product
Combined Temperature – RH probe
HP475AC1R
-
Relative humidity and Pt100 temperature combined probe, with SICRAM module.
-
Product
Meter Test & Calibration
-
Kongter Test & Measurement Co., Limited
Kongter offers a whole line of products for meter test and calibration including portable power source, standard reference meter and meter test system. All products are accredited to the highest production standards with different options of measurement accuracy (class 0.05 and class 0.1).These enable them to cover different applications for test and calibration of different types of energy meters, electric transducers, indicating meters and so on.
-
-
Product
Panel Meter Calibrator
1040C/CU
-
Calibrate panel meters, transducers, circuit breakers and relay units with Model 1040C, a portable, field-ready unit featuring eight key calibration functions.
-
Product
PXI Temperature Input Module
-
PXI Temperature Input Modules offer up to 32 channels of analog temperature measurements. Some models include autozero channels for offset compensation as well as open thermocouple detection to identify disconnected thermocouples, while others support 2-, 3-, or 4-wire resistance temperature detector (RTD) measurements. PXI Temperature Input Modules support both high-speed and high-resolution modes. You can program channel configurations and scale measured data into engineering units.
-
Product
CNC Rotary Axis Calibrator
API Swivelcheck
-
API SwivelCheck is light-weight & comes with a convenient carrying case to easily transport & install on a variety of CNC machines.
-
Product
Portable pH/mV Meter with pH electrode, temperature probe
CyberScan pH 11
-
5-point Push-Button Calibration with Auto-Buffer Recognition for quick calibration with no calibration mistakes
-
Product
Portable Protection Test Set and Calibrator
CMC 430
-
The CMC 430 is the preferred choice for test engineers in cases where excellent transportability is needed and three currents up to 12.5 A or six voltage outputs are sufficient. Its low weight of just 8.7 kg / 19.2 lbs, and robust design with its edge protection predisposes the device to every outdoor and indoor use.
-
Product
CO₂ Humidity And Temperature Sensor
SCD41 (Qwiic)
-
The SCD41 from Sensirion is a high quality Photoacoustic based CO₂ sensor capable of detecting 0 to 40000ppm with high accuracy over 400-5000ppm ±(40ppm+5%). In order to improve accuracy the SCD41 has integrated temperature and humidity sensing built-in. For additional accuracy the SCD41 also accepts ambient pressure readings!
-
Product
Non-Contact Temperature Measurement
-
These non-contact temperature measurement solutions are a diverse selection of industrial fixed, industrial handheld and human body temperature devices.
-
Product
Portable Analyzer and Calibrator
-
ECD’s portable analyzer and calibrator product lines are a simple convenient way to obtain fast, accurate pH and ORP measurements. They provide a milliVolt output signal for fast field analysis of samples, calibration verification, or trouble-shooting of installed sensors.
