Probe Interfaces
Connect ATE instrumentation to interface test adapter.
-
Product
Probes & Flow Cells
-
The sample interface is a virtual “windows into the process” and is a critical component of any optical analyzer system. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV/Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal transmission for long-term reliable measurements.
-
Product
Generic Probe Cards, PIB's, and Loadboards
-
Test Spectrum can provide generic Probe Cards, Probe Interface Boards (PIB), and loadboards. Choose from existing configurations already designed, or a generic test board for your specific tester configuration can be designed quickly.Teradyne J750 Probe Card and PIB; Teradyne Integra Flex PIB; Teradyne Ultra Flex PIB; Teradyne Catalyst PIB; Credence Quartet PIB (Probe Interface Board); Advantest 93K 1024 PIB
-
Product
NIR & UV-VIS Process and Lab Analyzers
-
The optical or spectrum analyzer is the brain which transforms the signal collected by the sample interface into actionable information. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV-Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal light transmission for long-term reliable measurements. More information is available about specific analyzers on each product page or on the process analyzer product overview.
-
Product
Utel Capture
-
Utel Capture is a complete telecoms network monitoring platform based on virtual (or physical probes for legacy interfaces) that enables data acquisition from control and user planes. It captures real-time data to provide valuable insights into network performance.
-
Product
Passive Probe Interface Adapter
CX1151A
-
The CX1151A is an adapter for passive probes for the voltage waveform measurements by the CX3300 series Device Current Waveform Analyzer.
-
Product
Probe Antennas
-
Probe antennas are offered as both standard and custom models with a rectangular waveguide interface. Probe antennas can only support linear polarization. These antennas are often used to measure the gain of other antennas by comparing the signal levels of the probe antenna and antenna under testing. The standard models operate across the full waveguide band and offer 6.5 dB nominal gain and 115 and 60 degrees half power beamwidth at center frequency. The below standard offering covers the frequency range of 8.2 to 170 GHz.
-
Product
Broadband Field Meter
NBM-550
-
*Intelligent probe interface detects probe parameters*Fully automatic zero point adjustment*Memory for saving up to 5,000 measurement results*PC software for convenient data management*Voice recording for comments*Conditional logging: Measured value saved when a threshold value is exceeded
-
Product
Fiber optic thermometer systems
TS Series
-
Micronor now offers a complete range of fiber optic temperature sensors, probes and interfaces for temperature measurement in challenging environments. TS series fiber optic temperature probes offer immunity to RF and microwave radiation along with wide temperature range, intrinsic safety and non-invasive use. The fiber optic temperature probes can operate over -200°C to +300°C (-328°F to +572°C), and withstand harsh and corrosive environments. Typical fiber optic temperature monitoring applications include:
-
Product
Pro Model Automotive Meter W/PC Interface
595
-
The #595 is a premier automotive diagnostic tool. It is equipped with the latest testing capabilities, including Milliseconds Pulse Width, for measuring the on-time of fuel injectors. The #595 features a huge LCD display w/bargraph for easy viewing. This meter can even be interfaced to your PC or notebook computer for enhanced diagnostics and data presentation. The software and computer interface cable are included free! The #595 includes two sets of test leads, RPM pick-up, temperature probe, software CD, interface cable, protective holster, 9 volt battery, instructions manual and hard storage case. Inductive RPM pick-up features a five position, adjustable sensitivity switch.
-
Product
25 GHz differential probe with ProAxial interface
DH25-PX
Differential Probe
25 GHz differential probe with ProAxial interface.
-
Product
Spring Probes & Hyperboloid Contacts
-
In-Circuit / Functional Probes, Socketless X Probes®, High Current Probes, Double Ended Probes, ATE Interface Probes, integraMate®
-
Product
30 GHz differential probe with ProAxial interface
DH30-PX
Differential Probe
30 GHz differential probe with ProAxial interface.
-
Product
Spring Contact Probes
-
FEINMETALL offers a wide range of contact probe:ICT / FCT probes, short travel probes, double plunger probes, fine pitch probes, interface probes, wire harness probes, threaded probes, high current probes, switch probes, twist proof probes, push back probes, koaxial probes, radio frequency probes.
-
Product
Broadband Field Meter
NBM-520
-
*Intelligent probe interface detects the probe parameters*Fully automatic zero point adjustment*PC software for convenient data management
-
Product
Probe Interfaces
-
Renishaw's range of interfaces makes it easy to connect a probe to your machine's controller.
-
Product
Drop-In In-Circuit Test Fixtures
The Chameleon
-
The Circuit Check kit called the Chameleon allows easy re-use of a majority of an ICT fixture’s major components. The Chameleon includes a full size probe plate and interface alignment plate so all valuable tester resources are available. The probe plate assembly is held in place with twelve (12) screws and the vacuum box’s interchangeable push plate is easily replaced by removing four (4) shoulder screws.
-
Product
Oscilloscope
RTM3000
Oscilloscope
Designed as daily problem-solving tool, the R&S®RTM3000 combines the power of ten (10-bit ADC, 10 times the memory and 10.1" touchscreen) with a Rohde & Schwarz probe interface for all Rohde & Schwarz probes.
-
Product
PXI LIN Interface Module
Interface
The PXI LIN Interface Module is a bus interface for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LIN Description File (LDF) databases in integrated LIN databases. PXI LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Interface Board, Low Cost, 8:1 Ethernet RJ45
40-965-901
Interface
Low cost converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 9 RJ45 sockets. Allows the multiplexing of up to 8 Ethernet signals with speeds up to 1G bit.
-
Product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785325-01
Interface
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Interface Panel for SLSC
THROUGHPOINT™
Interface
Bloomy's ThroughPoint™ Interface Panel provides a simple, yet highly-flexible connection between the unit under test and resources in a National Instruments Switch/Load/Signal Conditioning (SLSC)-based test system.
-
Product
PXIe Avionics Interface Cards
Interface
The OmniBus II PXIe is the next-generation of Astronics' popular OmniBus product with faster I/O and processing capabilities. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box. Readily available as Commercial Off-The-Shelf (COTS) products, the PCIe interface is perfect for challenging simulation, test, interface, and data recording applications.
-
Product
Interface
P-SER
Interface
P-SER I/O product is a native PMC form factor interface providing real-time serial input and output with high time-precision reception/input time-stamping, scheduled transmission/output, event triggering and interrupt support. This interface is designed to meet the needs of both the simulations/test and the real-time embedded applications whether in Windows or VxWorks environments.
-
Product
Compact-RIO Optical Interface Module
cRIO OPIF 20MBit/s
Interface
Fibre optical interface module for Compact-RIO with the following features:Fibre connection: SC connectorWavelength 820nmData rate: 020MBit/s2 Transmitters2 ReceiversExample SW in LabVIEWField of application of this module:Data communication via fibreOptical isolated data acquisition
-
Product
Interface
RAR15XF
Interface
On-board firmware, large data buffers, and a high-level API are integrated to provide total flexibility in monitoring and generating ARINC bus traffic. Simultaneous scheduled and burst mode (FIFO) messaging is supported on all ARINC 429 transmit channels. Each ARINC 429 receive channel provides simultaneous dedicated and buffered mode storage, along with label/SDI filtering.
-
Product
PCI-8232, IEEE 488 GPIB Instrument Control Device for Windows
778742-01
Interface
The PCI-8232 is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI-8232 can sustain data transfer rates up to 7.8 MB/s using HS488 and is IEEE 488.2 compatible. The PCI-8232 includes a license … for the NI-488.2 driver software, which provides high performance and maximum reliability for connecting to third-party instruments using GPIB.
-
Product
Interface
RXMC1553
Interface
Abaco Systems’ RXMC-1553 is the latest generation of performance and flexibility for MIL-STD-1553A/B Notice II on a XMC.0 Mezzanine Card. With one or two dual-redundant channels, the RXMC-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
4x IDC to 192 Pin Quadrapaddle
YAV90Q04
Interface
The interface YAV90Q04 permits to connect two YAV90096 boards to one 192-Signal contacts Quadrapaddle module. As the Mini-D 50 connectors let 2 free pins (1 and 26), these pins are interconnected to a test point, with the possibility of be grounded. Cable P/N J6200540: Mini-D-50 to Mini-D-50 IDC connectors with 400 mm flat cable.
-
Product
PCIe and PCI Avionics Interface Cards
Interface
Ballard PCI Express (PCIe) and PCI Avionics Interface Cards enable computers to interface with a variety of avionics databuses for testing, validating and simulating commercial and military avionics equipment and systems.
-
Product
Mini USB To 90 Series Interface (2)
J90USBR
Interface
Use in Receiver SideRequired Tripaddle Modules VPC 510104136
