Humidity Chambers
Controlled analysis of a product exposed to humid conditions.
See Also: Environmental Chambers, Chambers, Temperature Chambers
-
Product
Walk-in Environmental Chambers
EWS-SERIES
-
Mono-block/Pre-fabricated design EWS-Series Walk-in Environmental Chambers with custom-built features to meet testing needs of large-sized test specimens
-
Product
Temperature & Humidity Transmitter
HTO
-
- CO2 measuring element: NDIR Sensor 2- CO measuring element: Electrochemical sensor- Temperature/Humidity sensing element : CMOS sensor- Analog output option:4~20mA or 0~10V- Communication output option:RS485 Modbus RTU- Configured by PC with free software via USB cable (option)- Present value offset adjustable- Inside buttons for adjust output parameters- LCD backlight color to Indicated CO/CO concentration 2- Temperature measuring range can be -50~100℃ via USB console port to setting
-
Product
Humidity Bottles
-
Humidity bottles are made from type 316 stainless steel. Swagelok fittings for gas inputs and outputs are welded into the bottle. Nafion tubing is coiled in the bottle to provide dew-point humidity level for the gas passing through the tubing. The bottle is insulated and heated using a silicone rubber flex-pad.
-
Product
Thermal Shock Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL’s Thermal Shock Chamber provide the sudden temperature changes between extreme cold and extreme hot from -65℃ to 150℃ (customized available), specially for environmental stress screen test of the industries that rely on thermal testing, such as component, board electronic assemblies, defense, material stress, consumer products etc.
-
Product
Temperature And Humidity And Dew Point Meters
-
Omega offers a wide selection of multi-variable handheld temperature, humidity, dew point, and moisture meters. For data analysis choose a meter with data logging capability.
-
Product
Antenna Test Chambers
-
Special design for low PIM antenna measurements Shielding > 90 dB Frequency Range 700/1000 MHz to 6000 MHz Residual PIM < -165 dBc (@ 2 x 43 dBm) Up to 6 antenna ports for multi-band and MIMO antennas Standard models for antennas up to 2.7 m length Customized solutions available on request
-
Product
Hand-held meter for humidity / temperature
OMNIPORT 30OMNIPORT 30
-
The state of the art hand-held for precise measurement of various physical quantities, such as, humidity, temperature, dew point, air velocity, volumetric flow, air pressure. The numerous probes all incorporate high quality sensors developed by E+E and offer a total of 22 measurands.
-
Product
Environmental Test Chambers
TTC/CTC
-
Rapid, precise and energy-saving temperature changes in the range from -42 C to +190 C, along with fast humidity recovery times, make the TTC temperature test chamber and the CTC climatic test chamber with humidity unit a perfect duo for controlled material testing, function tests, ageing tests or climate tests on composites, concrete, plastics or electronic components in material technology, the automotive and aerospace industries, and electronics.
-
Product
Transmitters for Pressure, Humidity, Temperature, CO2
-
Wuntronic Transmitters for Pressure, Humidity, Temperature, CO2
-
Product
Thermal Shock Chambers
-
We provide a large selection of thermal shock chambers to accommodate various types of product testing. Thermal Shock Chambers perform tailored environmental stress screening of component and board electronic assemblies. Our unique chamber design transfers product between two extreme temperature-controlled chambers, passing equal volumes of high velocity conditioned air over the product and resulting in rapid product temperature changes. The induced thermal stresses can reveal hidden manufacturing defects in electronic sub-assemblies and other components by the expansion and contraction of critical parts.
-
Product
Walk-In Altitude Test Chamber
-
WEIBER Altitude Test Chambers combine temperature and altitude to test basic components or subassemblies designed for use in a variety of industries. With altitude test chambers, user can control the temperature environment for testing while simulating various altitudes from site level to 100,000 feet (1.12kPa)High and low Temperature Altitude Test Chamber is used to test temperature and low-pressure altitude conditions simultaneously. All models are factory tested, with an ergonomic and maintenance cum user-friendly design.These CE approved test chambers are created with multi-layered insulation with double vapor barrier is of low 'K' factor, high density and of non-hygroscopic in nature. WEIBER test chamber are made in accordance with the international standard.Standard as well as customizable models are available. Walk in models are also available.
-
Product
Ozone Test Chambers
-
Labodam Ozone Test Chambers are designed to detect the concentration of ozone while requiring low maintenance, having well-built corrosion resistant bodies, and while utilizing noiseless generators.
-
Product
Rain Test Chamber
-
Wewon Environmental Chambers Co, Ltd.
Water pump for rain test chambers uses highly pressure stainless steel pump, ensure water pressure and flow of the test cycle, the pump is installed in the side of the IP test device, and both ends of the inlet and outlet to set up the joint, easy to replace and repair. Water tank can be disassembled,The corresponding joint or hose connection is arranged in the water pipe connection.
-
Product
Air Temperature and Relative Humidity Sensors
-
Air temperature and relative humidity probes typically consist of two separate sensors packaged in the same housing. Often relative humidity is measured with a capacitive RH sensor, while air temperature is measured by a PRT.
-
Product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
Test Fixture
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
Product
Stability Walk-in Chambers
-
Stability walk-in rooms are an ESPEC North America specialty, designed for light-duty testing or long-term steady-state evaluation of pharmaceuticals and other products.
-
Product
Compact Temperature Chamber
FB1.5V-UHC Series
-
Based on the proven Bemco FB1.5V Compact Temperature Chamber, the FB1.5V-UHC offers spectacular temperature change rates in excess of 75 C per minute. With an extremely compact footprint these chambers cost about 1/3 of the amount of a typical 2-zone thermal shock chamber such as a Bemco FS2V.
-
Product
Hydrostatic Test Chambers
-
Test chambers are available to protect personnel during proof or burst testing. A few samples are pictured below. Chambers are manufactured in polished stainless steel with a clear polycarbonate door(s) for visibility during testing. Fluid port(s) are provided inside the enclosure, while all controls remain outside the enclosure for operator safety. In a hurry? Choose from our selection of Quick Ship Test Systems. basic units can ship within 24 hours or less and chamber systems within 2-3 days. we normally stock test chambers with nominal working area dimensions of either 24" wide x 24" deep x 15" high, 36" x 36" x 15", 48" x 24" x 15" or 72" x 24" x 12" with the door opening from the top. specify individual parameters at our customization page. Need a different size or configuration? No problem, simply specify dimensions and features that more accurately meet your particular requirements and we will be pleased to accommodate you. To customize a system to fit your particular application, please visit our customization page or give us a call at (916) 645-3317.
-
Product
Walk in Explosion-proof Chamber (Auxiliary Equipment)
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Walk in Explosion-proof Chamber is mainly used to test the safety performance of lithium ion battery, battery pack. Prevent test operators and other test equipment from being burned and exploding. At the same time, the explosion-proof test chamber with the smoke exhaust system can discharge the smoke generated in the test to the outside.
-
Product
Temperature shock test chambers test
TSS series
-
The operating principle of Schocktestprfschrank based of two superposed test rooms (top hot chamber, cold chamber below), between which a car with the test specimens is moved up and down by the large thermal shock test equipment may be subjected
-
Product
Walk-In & Drive-In Environmental Test Chambers
-
Weiss Technik Walk-In Drive-In environmental test chambers are available in many sizes and configurations for both pre-engineered and custom solutions. Ideal for testing large products, batches of products or for full vehicle testing with Panelized or Welded walk-in environmental chamber solutions.
-
-
Product
Moisture Resistance/ Humidity Test
-
This test is performed for evaluating the resistance of component parts and constituent materials to the deteriorative effects of the high-humidity and heat conditions typical of tropical environments. Most tropical degradation results directly or indirectly from absorption of moisture vapor, and from surface wetting. These phenomena produce many types of deterioration, including corrosion of metals; physical distortion and decomposition of organic materials; leaching out of constituent components of materials, and detrimental changes in electrical properties.
-
Product
Environmental Stress Screening (ESS) Chamber
ESS
-
Developed to help electronics manufacturers detect product defects and production flaws, Environmental Stress Screening (ESS) forces infancy product failures that would otherwise occur after final assembly and product delivery. ESS’s goal is to improve profitability by eliminating defective products. ESS Systems can meet individual performance needs, product loading, and throughput requirements. Thermotron has the experience to provide the best solution for ESS testing at your company.
-
Product
Rain Test Chamber
-
Xi'an LIB Environmental Simulation Industry
Simulates real-world rain exposure to test the waterproofing and weather resistance of products.
-
Product
Tensile Testing System With Thermostatic Chamber
-
This thermostatic chamber is ideal for long-stroke tensile testing of large-elongation materials such as rubber and plastic in controlled temperature environments.
-
Product
Proprietary LPWAN IoT Wireless Module W/ Temperature & Humidity Sensor
WISE-4210-S232
-
Proprietary LPWAN (Sub-G) wireless technologyProvides seamless cloud integration, supporting MQTT and RESTful API to upload temperature and humidity data to cloud platforms such as AWS, Azure, SCADA, and WebAccessOffers comprehensive protocol support, including MQTT, Modbus/TCP, SNTP, TCP/IP, HTTPS, RESTful, UDP, and DHCPBattery power for 5 years with 3 x 3.6V AA batteriesUp to 5 km communication range in open space
-
Product
Humidity Calibration
-
Trescal provides full Humidity Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Humidity Calibration services can be delivered at your site or at our lab. Accreditations for our humidity calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Safety Test Chamber Kit for both new and existing 8801 and 9801 testers US Army, USAF
8801HT/9801HT
-
The 8801HT retrofit safety test chamber kit is designed specifically for existing 8801-8801B and 9801B hydrostatic hose test systems in the field. It may also be ordered complete with a new 8801B or 9801B tester.
-
Product
Chambers and Glove Boxes
-
Standard Environments: ETS' multi-purpose benchtop units for laboratory and production use are large enough to accommodate testing and fabrication, as well as storage of materials, test equipment, and assemblies, yet they are small enough to fit on a standard workbench. The systems are able to independently maintain humidity from <5% to >95% RH and temperature from -22F to 122F (-35 to 50C) when unit is placed in an ambient environment location.
