Kelvin Leads
A spring clip where the jaws are insulated from each other at the hinge point. 4-wire
-
Product
Relative Humidity Kelvin Probe
RHC
-
The Relative Humidity Kelvin Probe (RHC) systems are the ideal solution for monitoring samples in a controlled atmosphere for contact potential difference (CPD)/work function (Φ) measurements.
-
Product
Test Leads
-
designed for electrical and electronics testing in today’s industrial environment.
-
Product
Test Leads
AL-34WB
-
Standard Electric Works Co., Ltd
● Wire length: 1.2m approx. Silicone insulated wire (1000mm) with wire connected to straight input plugs (130mm PVC wire), and wire for clamp (100mm PVC wire). ● Outside diameter of silicone insulated wire: 5mm Outside diameter of PVC wire: 3.5mm● Input plug color: Red•Green•Black•Blue ● Current rating: 5A● Voltage rating: 300V● Designed for Milliohm meter, Micro-ohm meter, Low resistance measurement with high current injection. ● Conductor size: 40mm maximum● Safety standard: IEC/EN 61010-031 CAT IV 300V
-
Product
The Mag Lead
136
-
*Mag Lead features a magnetic disconnect near the test probe end. *Just disconnect the test probe and you can “stick” to any metallic ground or test point. *Quit fumbling with alligator clips that fall off - Mag Lead’s powerfull magnet will hold tight! *This is a time saving tool - if you don’t have to walk to your tool box to retrieve your alligator clips, even on just half the occasions, then you’ve saved time. *Very helpful for automotive reference points and troubleshooting. *Can eliminate the need to hold probes while checking or monitoring a signal. *Two high power, low resistance magnets hold the probe to the lead. *Fits almost all Digital Multimeters and can be used with hand-held scopes too. *Get the Mag Lead, it stays put and won’t fall off, like alligator clips do!
-
Product
Kelvin Test Contactor/Probe Head
Gemini
-
At 3.22 mm test height, the Gemini™ Kelvin test contactor is an excellent all-around spring probe with low inductance, high bandwidth, and excellent current-carrying capacity. The device under test (DUT) side tip design accurately maintains its 100 µm spacing for the life of the probe. Customers report typical probe life of 500 k to 800 k package insertions, or over 2M touchdowns at wafer-level test. The offset tip allows manageable board layout with a board-side spacing of 0.4 mm.Gemini Kelvin probes and contactors provide a first-rate solution that effortlessly makes reliable, true Kelvin contact for high-volume final test of both singulated packages and wafer-level devices. Gemini Kelvin is an ideal solution for devices such as power controllers, A-D and D-A converters, power amplifiers and audio and video circuits.
-
Product
Scanning Kelvin Probe Microscope
VS-SKP
-
The Kelvin Probe experiment uses a nondestructive method to determine the relative work function difference between the probe and the sample. Work function describes the energy required to liberate an electron from the surface of a conductor; electrochemists often interpret this as the difference from an electrode’s Fermi Level, average energy of electrons, and that of vacuum.
-
Product
Test Leads
8000 Series
-
The "SOFTIE" by Probe Master lets you say "goodbye" to hand fatigue and finger calluses. A soft probe that bends 90 degrees or more. A probe that conforms to the shape of your hand. This soft flexible probe bends gently to reduce wear and breakage of the lead. Many combinations are possible with the "screw on" accessories shown above. The 48" long, 18GA. test leads, are made of top quality silicone.
-
Product
Test Leads
-
An IT professional who oversees the process of testing software before moving it to production.
-
Product
Fuse Lead Automotive DMM Test Leads
134
-
*ATC Fuse Holder In-Line *Provides extra overload protection *Can prevent your DMM’s internal fuse from blowing *For use with any Digital Multimeter
-
Product
Turret Kelvin Test Contactor
cHybrid
-
cHybrid™ Kelvin contactor contains a new and unique contact spring architecture which allows the test socket to adapt to challenging IC pad geometry requirements of todays and future small package types. Great lifetime up to 3 million touchdowns, with best-in-class contact resistance repeatability reduces cost of test significantly. A multi-beam contact structure optimizes signal integrity and current capability according to challenging electrical test requirements.cHybrid Kelvin contactor with multi-beam contact spring architecture delivers improved yield and long life minimizing cleaning cycles. This innovative solution will help customers reduce cost and maximize productivity.
-
Product
Assembled Test Leads
-
Carefully engineered from the ground up, Arbiter Test Leads combine performance, safety, and economy. All components are carefully selected to work well together, resulting in long life and excellent reliability.
-
Product
Test Lead Set
69128
-
Set of two (red, black) 32'' (813 mm) test leads.Each lead has alligator clips attached to both ends.Multi-purpose tooth pattern for better gripping of wires and test points.Recommended for general purpose measurements.
-
-
Product
Kelvin Test Contactor
ecoAmp
-
ecoAmp™ Kelvin test contactor has a durable monolithic pin design with low and stable contact resistance. It is a high-power cantilever kelvin contactor with a patented spring and tip design for optimum heat dissipation. This ensures best reliability, long spring life and high yield even under highest current and temperature requirements. Featuring extended Automotive temperature range -60 ̊C to +175 ̊C, capable to stand thermal stress during high-power test. The contact motion is decoupled from the test board.
-
Product
Leading Edge Sensors
-
The LaserGauge® Leading Edge Profiling System consists of a handheld or benchtop sensor and the Leading Edge software application. Designed to scan both sides of the blade simultaneously, the sensor returns a complete profile around the radius of the blade, which allows accurate measurements of the thickness and the plotting of the blade profile for comparison to its engineering design.
-
-
Product
200 Pin Male LFH to TriPaddle Flying Lead Cable, 36", 441655000-1
VFL135106-036
Flying Lead Cable
Vendor Flying Lead (VFL) Cable, 200 pin Male LFH to TriPaddle Leads, 28AWG Twisted Pairs - MULTI LEG 100 T/P's (1:2) 200 connection points, 4-40 fastener, VPC: 441655000-1, for 40-148-101, 40-148-201, 40-148-001, 40-140A-221, 40-140A-121, 40-140A-021, 40-670C-022 families, VPC contact 610110167 - TRI RCV (26-28AWG) (7 AMP/4 mΩ MAX), 36" length.
-
Product
Kelvin Contact Test
-
C.C.P. Contact Probes Co., LTD.
We offer different tip types for low resistance testing.
-
Product
Kelvin Contact Spring Probes
-
We have spring probes for Kelvin contact, which best suits to use for sensitive and extremely precise test. It is used by contacting to one terminal of semiconductor by two probes. We have 0.3, 0.4 and 0.5mm pitch probe for Kelvin contact.
-
Product
Test Leads
-
PMK Mess- und Kommunikationstechnik GmbH
It is used to test and measure the current in a circuit. These are simple devices which are coated and colored to indicate positive and negative with the device connector on one end.
-
Product
Automotive Test Lead Kit
143
-
Test Lead Kit includes our basic set of interchangeable specialty test probes designed for automotive use. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. The large Crocodile Clips are good for clipping to grounds and battery terminals. Roll up storage pouch keeps your leads organized.
-
Product
Test Leads
AL-34WB 10A
-
Standard Electric Works Co., Ltd
● Wire length: 1m approx. Silicone insulated wire (700mm) with wire connected to straight input plugs (150mm PVC wire), and wire for clamp (150mm PVC wire).● Outside diameter of silicone insulated wire: 6.4mm Outside diameter of PVC wire: 4mm● Input plug color: Red•Green•Black•Blue ● Current rating: 10A● Voltage rating: 300V● Designed for Milliohm meter, Micro-ohm meter, Low resistance measurement with high current injection. ● Conductor size: 40mm maximum● Safety standard: IEC/EN 61010-031 CAT IV 300V
-
Product
Kelvin Test Contactor
cCruiser
-
cCruiser™ Kelvin contactor was designed with cost of test optimization in mind, boasting a cantilever design that allows the testing of challenging discrete ICs and small logic package types. Providing a best-in-class proven lifespan of up to 5 million touchdowns increasing handler uptime. cCruiser reduces the cost of test for customers significantly, lasting longer and testing longer than previous contact solutions.
-
Product
Ultra-High Vacuum Kelvin Probe
-
Our Ultra-high Vacuum Kelvin Probes give the user full access to work function and contact potential difference (CPD) measurements under vacuum. Each system comes with a high-quality, manual, or motorized translator that enables reliable and accurate tip-to-sample positioning, and the unrivalled tracking system always holds the tip separation constant during the measurement. Even under vacuum, the work function resolution is 1 - 3 meV.
-
Product
XRF Lead Paint Spectrum Analyzer
LPA-1
-
The LPA-1 is a state-of-the-art Lead Paint Analyzer using X-Ray Florescence (XRF) and K-Shell technologies, providing readings in as little as 2-4 seconds. It is widely considered the fastest, most reliable lead inspection system today. Non-destructive testing for lead on painted surfaces. Fast, efficient and easy to use testing device. Completes readings in 2-4 seconds.
-
Product
Test Lead Set
34138A
Accessory Kit
The Keysight 34138A test lead set for digital multimeters contains fixed sheath banana plugs. The Keysight 34138A is compatible with the 34460A, 34461A, 34401A, 34405A, 34410A, 34411A, L4411A, and U2741A digital multimeters. 34138a is not compatible with 3458A instead use 34137A with 3458A.
-
Product
Lead Screw and Nut Assemblies
-
Kerk Lead Screw Assemblies are modified Acme thread forms optimized for performance and available in a broad range of lead screw diameters, leads and nut styles, custom designed for your application. Kerk lead screws are self-adjusting, maintenance-free and require no lubrication.
-
Product
Testing Leads Assortment (16PCS)
3605A
-
Peaceful Thriving Enterprise Co Ltd
1. For use on the 6-24V circuits.2. 4mm connection for banana plugs.3. Facilities the measurement on connectors and components without destroying the insulation or the plug connection.
-
-
