PXI Switching
See Also: PXI Matrix, ATE
-
Product
PXIe-2527, 32‐Channel, 300 V, 2‐Wire PXI Multiplexer Switch Module
780587-27
Multiplexer Module
32‐Channel, 300 V, 2‐Wire PXI Multiplexer Switch Module—The PXIe‑2527 is a high‐voltage PXI multiplexer switch module that is ideal for medium‑ to high‑density automated test applications. Featuring high-power electromechanical relays, the PXIe‑2527 is the perfect front end for the PXI DMM modules, offering simple channel expansion for a variety of measurements. The PXIe‑2527 supports multiple channel configurations including 64x1 1‑wire, 32x1 2‑wire, and 16x1 4‑wire. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
High Density Switch Matrix PXI Card
GX6616
Matrix Switch Module
The GX6616 is a 6U PXI switch matrix board that provides either differential or single-ended multiplexing capability through software commands, along with six groups of 2 x 16 that may be used in various configurations.
-
Product
Diagnostic Test Tool
BIRST™ (Built-In Relay Self-Test)
-
Verification and diagnosis of complex switching operation in a test system has always been an issue. BIRST (Built-In-Relay-Self-Test) diagnostic test tool provides a quick and simple way of finding relay failures available on some of our LXI and PXI switch matrices.
-
Product
PXI Dual Bus 32-Chan 2A Fault Insert Switch
40-190B-202
Fault Insertion Unit
The Dual Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Digital Stimulus Response PXI Card
GX5152 Series
PXI Card
The GX5152 Series are high speed, 6U PXI, digital I/O instruments. The GX5152 master controller has 32 I/O channels that supports test rates up to 50 MHz and vector depths up to 128 Mb per pin. The GX5153 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5152. The GX5152 can control up to 15 GX5153 boards using the same timing and sequencer.
-
Product
FPGA PXI Card
GX3601
FPGA PXI Card
The GX3601 is a 3U PXI FPGA card with 80, TTL buffered channels. The card is comprised of a GX3501 80 channel, TTL buffer expansion module and a GX3500 FPGA card.
-
Product
PXIe High Performance System Module: Dual Port (x16), Gen 3
M9023A
PXI Express Module
The M9023A is a PXIe System Module and is installed in the system slot of a PXIe chassis. When combined with an appropriate host adapter, it will provide a high data BW connection between the host PC and the chassis. The M9023A has a flexible configuration capability. Each card has two Gen 3 x8 PCIe cable links capable of achieving speeds up to 8 GB/s on each port. These two ports can be combined into a single x16 cable link providing a speed of up to 16 GB/s. This means a data-intensive system can be built using high-performance desktop or rack-mounted computers.
-
Product
PXI-2533 , 256-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-33
Matrix Switch Module
256-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2533 is a high-density 4x64 PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring solid-state relays (SSRs), the PXI‑2533 offers unlimited mechanical lifetime and the ability to route 55 W simultaneously on all channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
FPGA PXI Card with 40 Channel ECL Buffer Module
GX3640
FPGA PXI Card
The GX3640 is comprised of the GX3500 FPGA card and the GX3540, 40 channel ECL expansion card. It is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), and functional test applications. The GX3640 consists of 20 differential ECL drivers and 20 differential ECL receivers. Each channel can be accessed via software commands for use in static I/O applications.
-
Product
50-Pin SGMC Connector to Connector for Pickering Products
-
Our 50-Pin SGMC connector is used on PXI power switching products to provide a high current user connector solution with high density.
-
Product
Configurable High-Density Switch Matrix PXI Card
GX6384
Multiplexer Module
The GX6384 3U PXI multiplexer switch card provides users with the ability to switch and interface tester resources to multiple UUT connections. The card is available in three different configurations, supporting 32 x 2, 32 x 4, and 32 x6 switch configurations.
-
Product
PXI 4-Slot BRIC Matrix, 92x8, 1-Pole (2 sub-cards)
40-560B-021-92X8
Matrix Switch Module
The 40-560B-021-92x8 is an ultra high density matrix module and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
FPGA PXI Card with 80 TTL Differential Channels Module
GX3609
FPGA PXI Card
The GX3609 is a 3U PXI FPGA card with 80 TTL differential channels. The GX3609 is comprised of a GX3500 FPGA card and the GX3509, 80 channel, differential TTL expansion card.
-
Product
37 Pin D-type Connectors & Cables
-
These standard voltage and high voltage 37 Pin D-type connectors are used for both PXI & LXI switching and simulation products for medium density applications.
-
Product
PCIe Gen3 x8 FMC Module
PXI Express Module
VITA 57.1 FMC HPC ConnectorPCIe Gen3/Gen2/Gen1 x8 Slot (upto 64Gbps)Single module supports both PCIe Root Port & EndpointM.2 Key-M NVMe slot with PCIe Gen3 x2 interface & SATA3.0 interfaceMIPI DSI & CSI Connector through LVDS IOs32Kb-EEPROM
-
Product
PXI Solid-State SPST Switch, 6-Channel 25A 100V
40-184-001
SPST Switch
This range of PXI high power switches support 6-off high current SPST switches into two PXI slots or 3-off high current SPST switches into one PXI slot. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each PXI solid-state SPST switch can support 25A of continuous current and switch up to 100V signals. The switch can sustain inrush currents of up to 90A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
Push-Back & Push-Back Switch Probes
Switch Probe
Connector assembly check - extreme spring force - used in test modules.
-
Product
12-Ch SPST 4A-250VAC 24VDC High Current Power Switching
YAV90PIN
Switch Module
The YAV90PIN board is designed to cover the need to control the available power supplies in a test system to the device under test. A VPC 90 series connector is used as interface with the fixture, guaranteeing more than 20.000 mating cycles. Two connector contacts per relay contact are used.
-
Product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass
40-860A-332
Switch Module
The 40/42-860A-332 is a PXI/PXIe triple insert/bypass switch with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
High Density, 64-Channel Switch Card - 64 Channel, SPDT, High Isolation, Low Crosstalk Switch Module
1260-16A
Switch Card
The Astronics 1260-16A is a 64-channel, SPDT, high isolation; low crosstalk switch module designed for switching and routing sources such as AC and DC power supplies in automated test systems. The 1260-16A switches currents up to 6A, AC or DC, and voltages up to 110VDC or 250VAC.
-
Product
Automated Optical Switch - PXI
Optical Switch
Add optical switching capability to your test system with Quantifi Photonics’ automated optical switches. The fast and reliable optical switch will enable automated sequential testing, saving time and streamlining your test procedures.
-
Product
High 1.80 (51.00) - 12.60 (357.00) Switch Probe
TSP138-C180-3
Switch Probe
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 138Test Center (mm): 3.50Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,760Overall Length (mm): 44.70Switch Point (mil): 67Switch Point (mm): 1.70
-
Product
MSP Switch Probes
Switch Probe
Switch point flexibilityDesigned for long life and reliable performanceVariety of tip options
-
Product
PXI/PXIe MEMS Optical Switch, Quad Insert/Bypass, Single-Mode, 9/125 Fiber, LC Connectors
42-860A-442
Switch Module
The 40/42-860A-442 is a PXI/PXIe quad insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXIe Flexible Microwave Module, Dual SP6T Terminated 26.5 GHz, Single SPDT 26.5 GHz, 50 Ω, SMA
42-890-004
Switch Module
The 40-890 (PXI) and 42-890 (PXIe) range of PXI microwave modules allows users to specify the mix of relay types, frequencies and quantities based on the application requirements within the capabilities of the module driver card. Choose from the extensive relay selection already available in the Pickering microwave range to create a flexible solution.
-
Product
High 2.90 (82.20) - 12.60 (357.00) Switch Probe
TSP100-C100-3
Switch Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
Product
Standard 1.10 (31.18) - 4.80 (136.00) Switch Probe
TSP100-C100-1
Switch Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
Product
PXI Hybrid Dual Transfer Switch, DC to 26.5 GHz
M9156C
Switch Module
M9156C PXI Hybrid Dual Transfer Switch, DC to 26.5 GHz
-
Product
Switch Modules - 16 Two Pole Relays Arranged as an 8x2 Matrix
JX16/AB-2
Switch Module
This module has 16 two pole relays arranged as an 8x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 8x2's per chassis, or jumpered to the backplane to form up to a 128x2 two pole matrix. It is available with Type S, M or LT reed relays for high speed, long life application.
-
Product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 50Ω, SMB
40-870A-006
Switch Module
The 40-870A-006 (PXI) and 42-870A-006 (PXIe) are 50Ω RF switches with 6 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40/42-870A has been minimized by careful attention to the mechanical and electrical design.
