Satellite Simulation
provide the functionality to test satcom.
-
Product
PXI 6-Channel Battery Simulator Module
41-752-001
Simulator
The 41-752 is a 6 channel battery simulator, each channel being capable of supplying up to 7V and 300mA to the load. Each channel is fully isolated from ground and from each other allowing the channels to be connected in series to simulate batteries arranged in a stacked architecture. The 750V isolation barrier permits the 41-752 to be used to create a lower power version of a battery stack representative of those used for vehicle propulsion.
-
Product
PXI/PXIe Resolver Simulator Module, 4-Banks
43-670-201-AABBCC
Simulator
The 41/43-670-201 is ideal for the simulation of Resolvers. It has four banks, each capable of simulating the output of a single 5 or 6-wire resolver.
-
Product
VXI Synchro/Resolver Simulation & Measurement
65CS4
Simulator
NAI’s 65CS4 is a Synchro/Resolver Simulation & Measurement Instrument on a single-slot VXI board. The board incorporates up to four Synchro/Resolver measurement channels and up to four instrument-grade Synchro/Resolver simulation channels, or up to eight embedded grade Synchro/Resolver simulation channels that can be used independently and/or simultaneously.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel With V/I Readback
41-752A-012
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI RTD Simulator Module, 8 Channel, PT1000
40-263-403
Simulator
The 40-263-403 is an 8-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
-
Product
Satellite Signal Level Meter
Super Buddy
-
Complete more installs faster and better using the Super Buddy satellite finder meter. Be "sure of your bird" with the positive ID feature or use the automatic scan to identify the unknown satellite. The Super Buddy's geo-sensitive "Field Guide" shows you just the birds visible to your install -- ALL of them, with their individual transponders. The Super Buddy even gives the elevation and azimuth for whichever satellite you select.
-
Product
Simulation
-
From structural analysis and computational fluid dynamics to injection molding simulation and advanced, cloud-enabled capabilities powered by Abaqus, SOLIDWORKS® and 3DEXPERIENCE® Works Simulation provide integrated analysis tools for every designer, engineer, and analyst.
-
Product
PXI Millivolt Thermocouple Simulator Module - 32 Channel
41-760-001
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 350
40-265-014
Simulator
This module simulates the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems.
-
Product
Satellite Receiver For PCIe
DTA-2137C
-
Professional satellite receiver for DVB-S and DVB-S2 with two ASI monitoring outputs. This PCIe card outputs the full stream (not just a single service), either as BBFRAMEs or as a transport stream. Several advanced measurement capabilities are supported.
-
Product
Satellite Components
-
Digital Signal Technology, Inc.
Various satellite components, mainly transceivers for small satellites
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 750 V Isolation
43-752A-003
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
SIMULATOR
458-LM-A8-18A
-
Simulates 26 AWG PIC as specified in ANSI T1.417Bandwidth DC to 18 MHzIdeal for testing ADSL, ADSL2, ADSL2+, ADSL2++, VDSL,VDSL2(supports up to Profile 17a) modems/DSLAMs8 channels per line moduleLoop lengths programmable from 0 to 15,000 ft in 1,000-ft incrementsPlugs into our Model 458-CC-16 (16-slot) or 458-3SLB (3-Slot)chassisChannel-to-Channel isolation up to 90 dB
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, 1 kV Isolation
43-752A-101
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
9 Inputs Satellite Multi-Switch
HJMS-900B (Stand alone)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
*8 satellite IF & 1 terrestrial TV inputs. *Built-in amplification circuit to compensate cable loss.* 13/18V.22KHz and DISEqC. *Suitable for residential multiple LNBs reception. *Sheet Metal Housing.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCIe
ACPe825-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for PCIe with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825 PCIe card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
L Band Satellite over Fiber
-
Transport L Band signals from Satellite Dish to Receiver over Fiber Cable
-
Product
J1939 Simulator
DFLSJ1939BV1
-
The DFLSJ1939BV1 simulator is designed to simulate the truck or car''s ECU using J1939 protocol. It uses the DFL-SJ1939 IC with compact size. You can use free configuration software to customize the source address and 8 bytes of device name, and provide 2 extra customized PGNs. The configration software is free. You can download right now. New version 2.00 allows you to configure VIN#, and you can select J1939 DTC frame format from version1 to Version4. Furthermore, you can use our free PCTOOL software to change PGN value in real time.
-
Product
Satellite & Payload Check-Out Systems
-
Rovsing delivers systems for complete satellite or satellite subsystem testing. Rovsing has developed a modular test system architecture, based on S/W and H/W modules developed by Rovsing for most common space interfaces such as Power, TM/TC, MIL-STD-1553B and SpaceWire. A dedicated test system can then be composed by configuration of the modular architecture, installation of monitoring and control software, as well as test definition and scheduling software as required. Besides reduced development time, this has the advantage that the system to a large extent consists of elements that have been validated on previous missions.
-
Product
Simulation
-
Synopsys' high-performance simulation products help engineers find design bugs faster and achieve timely coverage convergence to create high-quality designs. The Synopsys suite of simulation solutions are tightly integrated, best-in-class technologies that allow designers to find bugs quickly and easily, significantly improving the quality of the most complex designs and enabling first-pass silicon success.
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 2k
40-265-306
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Patterning Simulation
-
KLA’s patterning simulation systems use advanced models to explore critical-feature designs, manufacturability and process-limited yield of proposed lithography and patterning technologies. Our patterning simulation software allows researchers to evaluate advanced patterning technologies, such as EUV lithography and multiple patterning techniques, without the time and expense of printing hundreds of test wafers using experimental materials and prototype process equipment.
-
Product
Simulation
-
Synopsys' high-performance simulation products help engineers find design bugs faster and achieve timely coverage convergence to create high-quality designs.
-
Product
PXI RTD Simulator Module, 12 Channel, PT500
40-263-302
Simulator
The 40-263-302 is a 12-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Accelerometer Simulator
MTN/8302
-
The MTN/8302 is a battery-powered unit designed to simulate a constant current type accelerometer. It enables test and calibration of vibration monitoring equipment such as the Monitran MTN/6000 series.
-
Product
Satellite Terminal Geolocation System
-
Satellite Terminal Geolocation System is designed to identify and locate sources of satellite transmission such as satellite gateway, VSAT Hub and VSAT terminals etc. The system is useful to the intelligence and defense agencies to identify the sources of satellite transmission of their adversaries and locate the terminals on digital map.
-
Product
Solar Simulator
XES Series
-
The recent environmental issues have been drawing more attention over the past few years. So "solar simulators" have come into the public eye much more often. They are mainly used for the evaluation of solar cells as well as for other types of tests where sunlight needs to be recreated.The continuous light of xenon lamp, the most faithful reproduction of sunlight, is applied in our highly accurate solar simulator, which has been widely sold across Japan and neighboring countries."SAN-EI" offer a wide range of solar-related optical technologies and can guarantee to satisfy the needs and request of customers.
-
Product
Modbus Simulator
Modbus Slave
-
Modbus Slave is for simulating up to 32 slave devices in 32 windows!. Speed up your PLC programming with this simulating tools. Start programming and test before you receive your slave device from supplier.
-
Product
Simulation Systems
System
Bloomy offers Simulation Systems for Hardware in-the-Loop (HIL) and open loop test of electronic controls and mechanical actuators for all types of transportation and defense systems including aircraft, rail, automobiles and ships. These systems, now deployed at major aerospace, locomotive and military manufacturers and research facilities worldwide, provide world-class, high-fidelity simulated environments for use in both closed-loop and open-loop testing. Because Bloomy’s Simulation Systems are largely constructed from COTS components, time to first test can be reduced significantly, and their highly-customizable nature allows your test system experts to provide your unique IP to differentiate your product from your competitors.
