Differential Phase-Shift Keying
-
Product
25 GHz Differential Probe with 2.92mm Interface
DH25-2.92MM
Differential Probe
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Flow And Differential Pressure Sensors
-
ACEINNA’s flow and differential pressure sensors are designed to serve the need for mass flow and pressure sensing in multiple applications such as gas meters, process control, HVAC, medical, chemical, food and beverage, etc. We offer two newly launched and announced product lines, the MFC2000 family of gas flow modules and the MDP200 differential pressure sensor.
-
Product
Explosion-Proof Differential Pressure Switch
1950G
-
The Model 1950G Explosion-Proof Switch combines the best features of the popular Dwyer Series 1950 Pressure Switch with the benefit of natural gas compatibility. Units are rain-tight for outdoor installations, and are UL listed for use in Class I, Groups A, B, C, & D; Class II, Groups E, F, & G and Class III atmospheres, ATEX for EExd IIB & Hydrogen T6, and CSA & FM approved for Class I, Div. 1, Groups B, C, D; Class II, Div. 1, Groups E, F, G and Class III atmospheres
-
Product
InfiniiMode Active Differential Probe, 1.5 GHz
N2750A
Oscilloscope Probe
The N2750A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2750A probe’s InfiniiMode provides the following modes of operation.
-
Product
Differential Pressure Transmitter
636D
-
The Series 636D Differential Pressure Transmitter can be used for measuring pressures of liquids, gases & vapors. All available ranges have an excellent 0.5% F.S. accuracy with a 4-20 mA Output standard or optional 1-5 VDC output.
-
Product
Compact Economic Differential Pressure Switch
PDPS
-
The Series PDPS's large diameter diaphragm and snap action switch make it dependable and ideal for OEM applications. The Series PDPS Pressure Switches are available for pressure, vacuum, and differential applications and are factory preset for pressures from 0.07 in. of w.c. to 1.0 in. of w.c. with full-scale repeatability of ±0.02 in. of w.c.
-
Product
Relative and Differential Pressure Transmitters
HD408T… / HD4V8T… Series
-
HD408T, HD4V8T are analog output relative or differential atmospheric pressure transmitters; they are used in all those applications where non corrosive air or gas need to be monitored, with pressure fields from 10 mbar to 2000 mbar.
-
Product
Differential Probe
DP-16V
-
*MAX. Input Voltage: ±8KV DC or 16KV p-p or AC 5.6KV rms*Bandwidth: DC-50MHz*Input Impedance 30MΩ// 1.5PF*x20, x200, x2000 Attenuator*To Ground MAX. Voltage: 8KV CAT III*Output Impedance 50Ω
-
Product
30 GHz differential probe with ProAxial interface
DH30-PX
Differential Probe
30 GHz differential probe with ProAxial interface.
-
Product
CO2 Air Quality & Differential Pressure Measurement
-
Our Rotronic CO2 and differential pressure instruments complete the PST range of parameters important for environmental monitoring.
-
Product
Manometer for Differential Pressure
MANO2-A
-
An instrument for measuring the pressure acting on a column of fluid, especially one with a U-shaped tube of liquid in which a difference in the pressures acting in the two arms of the tube causes the liquid to reach different heights in the two arms.
-
Product
VME 16-channel Differential to Single-Ended Signal Converter
V1250
-
The V1250 is a 16 channel differential to single ended signal converter in a 1-unit wide VME 6U form factor. It provides differential inputs (34-pin 2.54 mm header, Zdiff = 100 Ω) and single ended outputs (coaxial LEMO, Rout = 50 Ω).
-
Product
Differential Pressure Transmitter
607
-
Series 607 Differential Pressure Transmitter combines very low ranges with exceptional stability, reliability and either ±0.25% or ±0.5% accuracy for the most demanding applications. Ranges from 0-0.1" to 0-25" w.c
-
Product
Parallel Differential Battery Tester With Integrated Chamber
-
Accelerate your battery parallel test using our PDBT. Featuring an integrated chamber, it precisely conducts battery comparison test and fast measures battery's self-discharge current. Its portable, powerful design is perfect for innovative research applications.
-
Product
InfiniiMode Active Differential Probe, 6 GHz
N2752A
Oscilloscope Probe
The N2752A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2752A probe’s InfiniiMode provides the following modes of operation.
-
Product
Magnesense Differential Pressure Transmitter
MS
-
The Series MS Magnesense Differential Pressure Transmitter is an extremely versatile transmitter for monitoring pressure and air velocity.
-
Product
Differential Probe
DP-60HS
-
*High Sensitivity Model: x 1, x 5, x 10 Attenuation*1 MΩ // 10PF Input Impedance*High Frequency Operation: x 1(30 MHZ), x 5(60 MHZ), x 10(60 MHz)*Especially For Low Voltage: x 1(7 Vp-p), x 5(35 Vp-p), x 10(70 Vp-p)
-
Product
Electronic Differential Pressure
Density Measurement
-
An innovative software and hardware concept makes it possible to combine any two pressure transmitters of the VEGABAR 80 series into an electronic differential pressure system to measure density. Electronic differential pressure measurement is used for measuring density change and/or for compensation when the level needs to be measured.
-
Product
Connector Interface, Connector Type FC - Narrow Key Way
81000NI
Interface
81000NI - FC/APC connector interface, good for >10000 reconnection cycles, 2.03mm (0.08") key way. (for R-keying only, narrow key way)
-
Product
Gas Permeability Tester with Differential Pressure Method
GPT-203
-
GPT-203 Gas Permeability Tester is based on the differential pressure method and is professionally applicable to the determination of permeance and permeability of plastic films, composite films, high barrier materials, sheeting, metal foils.
-
Product
Acute High Voltage Differential Probe, 10x/100x, 25MHz, 700V
ADP1025
-
*USB Powered (or Power Bank)*Bandwidth up to 25 MHz*Overrange Indicator*Audible Overrange Alarm*Bandwidth Limit : 5 MHz / Full*Can be used by any DSO which has the USB port(s).*EC Declaration: EN 61010-031:2002 +A1:2008*Double-layer wire for power insulation
-
Product
M-LVDS (Multi-Point Low Voltage Differential Signaling)
-
M-LVDS (multipoint low voltage differential signaling) is a multipoint high speed differential electrical interface with support for up to 32 nodes. Analog Devices M-LVDS products offer the industry’s highest ESD performance transceivers with high noise immunity receivers and extended common-mode range. These products are ideal for applications where designers need to transmit at data rates up to 100 Mbps or 250 Mbps to multiple nodes.
-
Product
32-Channel RS485/422 Differential
4792
-
The Conduction Cooled 32-channel Reconfigurable RS422/RS485 Digital I/O PMC provides a vehicle for implementing complex user-specific digital designs requiring a differential interface. Thirty-two (32) generalpurpose RS422/RS485 driven digital I/O differential pairs are wired to the rear PN4 connector. For each of the 32 channels, the bidirectionality is controlled by an output from the FPGA.
-
Product
AD06A Baratron® Differential Pressure Sensor
-
AD06A Baratron® differential pressure sensors are single-ended dual-electrode/AC bridge devices that are extremely stable and designed to minimize the effect of temperature changes. Full Scale ranges are available from 25,000 Torr down to 0.1 Torr. Each range measures down to 1 part in 106 Full Scale with selected percent Reading accuracy limited by this resolution and with accuracies ranging from 0.25% to 0.05% of Reading. They are constructed of Inconel® and stainless steel, allowing use with many wet, dirty, or corrosive gases.
-
Product
High Voltage Differential Probe
ADF25A
-
Permits conventional grounded oscilloscopes to be used for the display and measurement of multiple floating signals with high common mode voltages
-
Product
VPX Extender 6U - P0 Utility, P1 Differential, P2 Single-Ended Signals, And P3-P6 Differential Pairs
119EXT6024-06XXR
-
VPX Test Extender 6U 240mm.
-
Product
Acute High Voltage Differential Probe, 20x/200x, 25MHz, 1400V
ADP2025
-
*USB Powered (or Power Bank)*Bandwidth up to 25 MHz*Overrange Indicator*Audible Overrange Alarm*Bandwidth Limit : 5 MHz / Full*Can be used by any DSO which has the USB port(s).*EC Declaration: EN 61010-031:2002 +A1:2008*Double-layer wire for power insulation
-
Product
Differential & Telecoms PXI Switching Modules
-
Ideal for switching signals carried as differential signals where a controlled differential impedance is required
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
CAN Interface
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
Differential And I/Q Device Measurements
S95089B
-
The S95089B combines source-phase control of multiple internal or external sources with frequency-offset mode, enabling simplified test of I/Q modulators/converters, differential mixers, and harmonics or amplifiers.
