RTD Simulation
calibrate resistance temperature detection systems.
-
Product
2 PRI + 32 BRI-U ISDN Simulator
CH-32BRI-U-MOD-2PRI
-
This unit has two PRI ports and 32 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
Product
MIL-STD-1553 A / B Test And Simulation VXIbus Module
VXI-1553
-
*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
Monitoring & Simulation
-
ETAP Power System Monitoring & Simulation (PSMS) is at the heart of the ETAP Real-Time power management system. Power System Monitoring & Simulation is the smart choice for both small and large electrical utility systems, generation plants, industrial sites, manufacturing facilities, and off-shore oil platforms.
-
Product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Avionics Test & Simulation Software
-
Ballard CoPilot® is an intuitive, graphical software program that allows you to easily monitor, record, replay, analyze, and simulate avionics bus data. With CoPilot you can interact directly with data on multiple buses using Ballard avionics interface hardware or work with previously recorded data. This advanced program features powerful tools for development, testing, troubleshooting and maintenance of avionics equipment and systems.
-
Product
20KV 30KV Electrostatic Discharge ESD Simulator
20KV/ 30KV Electrostatic Discharge ESD Simulator
-
Shenzhen Chuangxin Instruments Co., Ltd.
ESD simulator (Electrostatic Discharge Generator or Electrostatic Gun) is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performance. ESD-0230/ESD-0220 has LCD display in both English and Chinese, they equipped with an infrared remote control which can allow you do the test in some special place.
-
Product
GPS Simulator
MVT-NSSG
-
The Navigation Spread Spectrum Generator can be used for precise GPS M-Code interference tests with existing GPS C/A and P/Y receivers. The simulator is capable of generating all the current GPS signals simultaneously with the new modernized signals and codes. Optional models can be configured with unique user defined signals, such as would be required for GLONASS.
-
Product
CAN & LIN bus Custom Test & Simulation Software
CanX
-
Schleissheimer Soft- und Hardwareentwicklung GmbH
CanX is the custom testing and simulation software for CAN and LIN bus for specific user groups. The run-time software is designed to execute predefined or automated tasks in testing, work preparation, production, repair or project management.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 8 Channel
43-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
PXI & LXI Simulation Tools
-
Would you like to do code development with minimal hardware or see real-time switching and debug information? The LXI Simulation Tool can do that for you. This tool supports the simulation of all our PXI and LXI switching products, and most of the PXI simulation products in one highly portable package. The tool provides you with a simple and highly portable platform for application development.
-
Product
Regenerative Grid Simulators
-
Chroma Systems Solutions, Inc.
Rigorous testing to industry regulatons and standards for the safe operation of on-grid products.
-
Product
ARINC-429 Multi-Channel Test & Simulation Module for Excalibur 8000 Family of Carrier Boards
M8K429
Carrier Board
The M8K429 is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 8000 family of carrier boards. The module supports up to five ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word. The receivers allow for filtering and multi-storage modes of Data Words. The transmit channels operate via a transmit ‘instruction stack’ which allows scheduling of data transmissions and reduces the need for host computer intervention.The M8K429 comes complete with C-driver software library including the source code.
-
Product
DGS-65 Test Panel with FV Simulator / Bed of Nails
TA-650
-
The TA-650 is a new test fixture that will give any instrument shop the ability to conduct more detailed testing of the Collins DGS-65 directional gyro then was previously available.
-
Product
Single or Dual Stream MIL-STD-1553A/B Test and Simulation Modules
AXC1553-xT
-
MIL-STD-1553 Test and Simulation modules for XMC with 1 or 2 dual redundant streams plus 8 Discrete I/O’s (on Rear-I/O).*Concurrent BC, MRT (31) and Chronological/Mailbox Bus Monitor*Full Error Injection/Detection (AS4112)*Complex Triggering, Data Capture/Filtering & 100% Bus Recording*Physical Bus Replay*IRIG-B Time Encoder/Decoder*Programmable Bus Coupling, onboard Bus Network and variable Output amplitude*Full Function, Single Function and Simulator Only versions available*Drivers for Linux and Windows*Optional Databus Test and Analysis Software and RT Production Test Plan
-
Product
ARINC 429 Test And Simulation USB Module
USB-429
-
*4, 8 or 16 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Infrared Simulation Services
-
INO offers a simulation service to assist with the hardware and software design of infrared and electro-optical devices. Precise performance predictions help integrators understand application requirements and bring application performance in line with client specificationsbefore the advance design and fabrication phases. For a minimal investment, infrared simulations help minimize risk in the early stages of development.
-
Product
Compensation Block for Thermocouple Simulator Modules
40-965-912
Isothermal Termination Block
The Compensation Block is a accessory specifically designed for the 41-760 and 41-761 Millivolt Thermocouple Simulator modules. This block will give the user the temperature of the front panel junction of the module to cabling. This data can then be combined with other factors, temperature on the other end of the cable for example, to compensate the thermocouple hence increase the accuracy.
-
Product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
Signal Integrity Studio, Analysis & Simulation SW for WAVEPULSER High-Speed Interconnect Analyzer
WavePulser-Signal Integrity (SI) Studio
Analyzer
WavePulser Signal Integrity (SI) Studio is included as a single license in the WavePulser 40iX-BUNDLE or can be purchased as an additional license for offline access to additional users. WavePulser Signal Integrity (SI) Studio combines S-parameter, Impedance profiling and de-embedding measurements, channel and equalizer modeling, eye diagrams and jitter analysis in a single affordable software package for emulating the complete serial data channel.
-
Product
Simulators
-
The Autonomous Air Combat Maneuvering Instrumentation System's unique combination of advanced air-to-air and air-to-ground combat training ensures air commands optimum utilization of flight hours and other valuable resources. Each system is fully customizable to address the skill sets of each operator. Key features include real-time kill weapons delivery, and electronic warfare attack notifications.
-
Product
MIL-STD-1553 A / B Test And Simulation VME Module
VME-1553
-
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
High Frequency Noise Simulator
SKS-H04GA
-
Shanghai Sanki Electronic Industries Co., Ltd.
The high-frequency noise simulation generator is an EMC test instrument that reproduces high-frequency noise with a fast rise time when the switch is turned on/off. Since the pulse rise time is less than 1ns and contains wide bandwidth noise, it is very suitable for reproducing malfunctions. The line noise entering the power line and the induced noise entering the communication line can be reproduced, and the performance evaluation of the malfunction and function degradation of electronic products can be performed.
-
Product
Bipolar DC Power Supply / Battery Simulator
IT6400 Series
-
The unique bipolar voltage/current output makes IT6400 series can be used as a bipolar power source or a bipolar electronic load. The battery simulating function is especially applicable for development and high speed production testing of portable, battery-operated products.
-
Product
Synchro/Resolver Conversion & Simulation PMC boards
-
Versatile, rugged, and time saving Synchro/Resolver conversion and simulation PMC boards featuring multiple high accuracy, independent channels and easy programmability, to provide a highly accurate and convenient method to test and simulate positioning systems in lab and embedded environments. The SB-3642 conversion and SB-3644 simulation boards’ versatility and ruggedness enable them to be used first in the lab, and then be readily designed into embedded applications, just by the switch of a carrier card.
-
Product
Multiphysics Computational Fluid Dynamics (CFD) Simulation & Analysis
STAR-CCM+
-
Siemens Digital Industries Software
STAR-CCM+ is a stand-alone simulation solution for computational fluid dynamics (CFD), computational solid mechanics (CSM), heat transfer, particle dynamics, reacting flow, electrochemistry, electromagnetics, acoustics and rheology. STAR-CCM+ delivers accurate and efficient simulation technologies through a single integrated user interface and automated workflows. This facilitates the analysis and exploration of complex real-world problems.
-
Product
1 Or 2 Stream MIL-STD-1553 PMC Test And Simulation Modules With Prog. Coupling,onboard Bus Network And Variable Output Amplitude
AMCX1553-xT
-
MIL-STD-1553 Test and Simulation modules for PMC with 1 or 2 Dual Redundant streams plus 8 Discrete I/O’s (on Rear-I/O).
-
Product
Environmental Shock Simulation Machine For Drop Testing
-
# Simulates environmental handling threats small handheld products must survive.# Gauges your product?s ability to survive handling environments.# Controls key test variables: product orientation at impact; nature of the impact surface.# Maintains orientation to just prior to impact then releases for unrestrained impact.# llows user changeable impact surfaces to better simulate the handing environment.# Includes 4 ch short transient shock instrumentation system.
-
Product
Offline Programming, Advanced Simulation & Digital Twin
Silma
-
Improve your 3D measurement experience with a winning combination: Silma, for advanced simulation and digital twin of your 3D measurement process, and Metrolog for on-machine execution and analysis.
-
Product
MIL-STD-1553 Simulator & Analyzer Applications Software
F-SIM-1553
-
Avionics Interface Technologies
Software GUI Application for Operating AIT MIL-STD-1553 Interfaces - Bus Monitor Captures & Recordings - Simulate Bus Controller and Remote Terminals (up to 31) - Operate Multiple Bus Channels (and MIL-STD-1553 Modules) Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Engineering Unit Displays & Software Widgets - MIL-STD-1553 A/B Mode Code operations - Also Supports ARINC 429, ARINC 664, Ethernet, & Data Load operations
-
Product
Battery Cell Simulator
BCS-LABCAR
-
The ETAS Battery Cell Simulator (BCS-LABCAR) is a Hardware-in-the-Loop system which specifically targets the signal-level test, validation, and calibration of battery management systems (BMSs). The BCS-LABCAR is a high-precision Battery Cell Simulator that emulates the behavior of individual battery cells and packs across a wide range of challenging operating conditions, e.g. cell balancing over-charging, deep discharging, or pulse operation. The system is highly modular and thus scalable to emulate battery packs from a single cell all the way up to 200 cells.
