Dielectric Withstand Testers
check insulation to assure current does not flow through it.
See Also: Hipot, DC Hipot, AC/DC Hipot, Hipot Testers
-
Product
Programmable Withstanding Voltage & Insulation Test
LS9923
-
LS9923 programmable withstanding voltage & insulation test system is high-performance testing device special for AC&DC Withstanding Voltage and Insulation Resistance Test, It allows setting the output voltage. The warning value,testing time and some other parameters can be set in the screen.It with a variety of automatic test functions. The testing is quick and high accuracy which is not only applied in the production line but also in the develop research.
-
Product
For Dielectric Oil Test
Stoil Cell
-
The option allows the testing of the insulation characteristics of the oil by checking if there is no contamination.
-
Product
Dielectric Oil Testers
-
Electrical insulation oils form the critical insulation medium for many of today’s electrical apparatus, such as transformers, tap-changers, circuit breakers, cables, bucket trucks etc.
-
Product
A C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
AVC-25V
-
A C DIELECTRIC STRENGTH TESTERS ( HIPOTS ). Two high-voltage leads, one c/w a clip and one c/w a retractable probe. Each is 2 meters (6 ft) long.
-
Product
Dielectric Strength Test Apparatus
CX-KD12
-
Shenzhen Chuangxin Instruments Co., Ltd.
To improve the insulation board and creepage dielectric properties, surface brushed polished, bottom bracket the minimum distance from the edge of >35mm, the altitude of 2000 meters designed to meet the strength test requirements of 12KV
-
Product
A C & D C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
AV/DV-50VA-10V
-
A C & D C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
-
Product
Impulse Withstand Voltage Tester
SUG255
-
The Impulse Withstand Voltage Tester (or High Voltage Surge Generator), it is according to IEC255-5, IEC60060, IEC60065, GB14711, GBT17215.301 and GBT17215.322. It is suitable for doing all kinds of electrical and electronic products (such as energy meter, household appliances, low voltage electrical appliances and small power motor) insulation performance test.
-
Product
Dielectric Loss Tangent Testing Instruments
-
Insulation materials in electrical equipment are used between a pair of electrodes; therefore it can be expressed as capacitors. Applying AC voltage to a capacitor with insulation materials causes an energy loss due to the leak current, the dielectric polarization, and the partial discharge. Because of this, the phase of the capacitor current is more delayed than that of a zero-loss current (reactive current) flowing in an ideal insulation material. The delay angle is called "Dielectric Loss Angle", and the tangent is "Dielectric Loss Tangent" (tanδ). Please refer to the technical guide explained in detail.
-
Product
Dielectric Cure Monitoring Software
CureView
-
CureView dielectric cure monitoring software is a complete control and analysis package for operating all Lambient Technologies products. Our easy-to-use CureView software provides the flexibility needed in research and development along with user-configured operation for QA/QC and manufacturing applications.
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
0-5KV AC Withstand Voltage Tester
2670A
-
Shenzhen Chuangxin Instruments Co., Ltd.
0-5KV AC withstand voltage tester Features: High voltage,small current, high accuracy. Leakage current, testing time, continuous arbitrarily, well-adapted.
-
Product
Solid Dielectric Test Cell
-
• 3 terminal design • 70pF at 1mm gap nominal capacitance • Max test voltage of 2.5kV AC or DC • Suitable for use with Eltel models DTR-3K, ADTR-2K Plus Test Sets
-
Product
DC Overvoltage or Withstand Testing
-
Overvoltage protection is critical to the long-term health of any cable. DC overvoltage testing (also known as withstand testing) is the most popular method of general condition and integrity assessment in the power, industrial and domestic markets. This method of testing is distinguished a number of key advantages:
-
Product
Transformer Oil Dielectric Strength Testing
LS -JJ-II
-
Chongqing Lushun Scientific & Technological Development Co., Ltd.
1.The instrument has the function of automatic detection. 2.Tiny TPU-A panel printer is adopted for automatic printing out type insulating oil dielectric strength ATE is a full self-reacting device, which is developed according to the requirements in International IEC-156 and International GB507-86 "Insulating Oil Dielectric Strength Mensuration", combining the feedback opinions of all users .The instrument adopts singlechip as the leading part, and uses the method of "first setting and then testing". The whole process is controlled by automatic microcomputer. It is operated simply and used conveniently.
-
Product
Dielectric Withstanding Voltage Test
-
The dielectric withstanding voltage test (also called high-potential, over-potential voltage-breakdown, or dielectric-strength test) consists of the application of a voltage significantly higher than rated voltage for a specific time, between mutually insulated portions of a component part or between insulated portions and ground. This is used to prove that the component part can operate safely at its rated voltage and withstand momentary over-potentials due to switching, surges, and other similar phenomena.
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
Programmable AC/DC Withstanding Volatge And Insulation Tester
RK-7122
-
Shenzhen Chuangxin Instruments Co., Ltd.
Programmable AC/DC withstanding volatge and insulation tester
-
Product
AC & DC DIELECTRIC STRENGTH TESTERS ( HIPOTS )
AV/DV-25VA-5
-
A C & DC DIELECTRIC STRENGTH TESTERS ( HIPOTS ).
-
Product
Programmable AC Withstand Voltage Insulation Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
*Small volume, light weight *Easy to operate, has keyboard lock function *Provide 5 groups memory setting, each group has four kinds of work mode LCD display Voltage gradient rise by time, real-time analysis and look for breakdown point
-
Product
Dry Dielectric RF Coaxial Loads
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
Product
Dielectric Strength Meter
Dielectrotest
-
The Dielectrotest is a fully automatic dielectric oil meter for determining the breakdown voltage of insulating liquid. It is designed for both laboratory and field use for commissioning and maintenance purposes. The test standard is selected via menu.
-
Product
Pitot Static Tester / AoA TESTER
ADSE 744
-
This tester was specifically designed for the new-generation pitot tubes that integrate sensing probes, pressure sensors and powerful air data computer processing to provide all critical air data parameters including Pitot and static pressure, airspeed, altitude, and angle of attack. This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The AoA Channel behaves as a second Ps channel, in order to create a differential pressure between the 2 Ps Channel, allowing to performsimulations of different Angles of Attack. The large touch screen display, with on-screen help, enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator. The ADSE 744 is robust and housed in amobile weatherproof case. An attached bag contains the pressure hoses and electrical cables.
-
Product
Torque Testers
-
Welcome to our comprehensive selection of torque testers. Whether you’re looking for torque gauges, cap torque testers, or manual torque wrench calibrators, we have everything you need to ensure your equipment is functioning at its best. Our wide range of products includes both manual and motorized options, so you can choose the best option for your specific needs. Our digital torque screwdrivers and wrenches are perfect for precise torque control in assembly and manufacturing applications. For even greater convenience, we offer wireless digital torque wrenches that eliminate the need for cumbersome cables. Our power tool calibrators, impact tool calibrators, rotational friction torque testers, and breakaway torque testers provide reliable and accurate testing, so you can be sure your equipment is functioning at optimal levels.
-
Product
Multifunction Testers
1663
-
The 1663 installation tester delivers the full-featured functionality and advanced measurement capabilities that professional installers need. It is compact and lightweight (less than 1.3 kg) and comes with a padded carrying and waist strap for convenient handling.
-
Product
Torque Tester
WDI series
-
New standard torque tester. Manage electric screwdrivers, manual torque screwdrivers, and wrenches with this one unit! WDI-10HR WDI-100HR WDI-250. THE CULMINATION OF 50 Years of Manufacturing TORQUE MEASURING TOOLS.
-
Product
Battery Tester
700
-
The #700 has an internal loading capacity of 100 amps. It is a great tool for finding batteries that can’t stand up to the load of today’s automotive accessories. It will also test relative starter current draw and charging voltage.
-
Product
CCTV Tester
M-IPC-200A
-
Fuzhou Metricu Technology Co Ltd
3.5 inch IP camera tester M-IPC-200A with analog, HD-TVI, HD-CVI, AHD
-
Product
Torque Tester
WDISR-IP series
-
Management of manual torque tools Built-in battery type. For managing various torque drivers and wrenches. Interlocking with a personal computer or PLC, the torque measurement can be managed at a higher level.
-
Product
Capaciter Tester
KS-1600
-
Konstar Electric Industrial Co., Ltd
It is a dial instrument, and has the stable function and high reliability. It is driven by the battery. The instrument makes use of the indicator plate(102*79mm), thus displays clearly.This instrument can test the data of on-line capacitive resistance and on line impedance. It is an excellent instrument and an ideal tool for the people in labs, factory and household. When testing the mounted capacitor, it does net need to be completely out of power nor do the meter, and the meter can be testing continuously.
-
Product
HD-TVI Tester, HD-CVI Tester, AHD Tester
M-IPC-300 series
-
Fuzhou Metricu Technology Co Ltd
4 inch IP camera tester
