Battery Testers
verify battery integrity.
See Also: Battery Test, Testers, Battery Checkers, Battery Capacity Testers, Lead Acid Battery Testers, Battery Conductance Testers, Battery Connectors
-
Product
Glow Plug Tester
-
The analyser test the condition of the glow plug in diesel engines and it comes with a graphical display without any language it shows the actual resistance of the glow plugs with conclusive result after the test. The analyser will switch off automatically if the tool is not being used, to conserve battery life. The tester comes with a built-in torch light to light-up dim surroundings for finding the glow plug or other car electrical problem.
-
Product
pHTestr® 5 Waterproof Pocket Testers
-
These pocket-sized testers have a replaceable single-junction sensor which can be easily switched out, allowing you to save money by using the tester body over and over again. A large LCD makes viewing measurements easy and features a three-color backlight indicating operational mode—blue for measurement, green for calibration and red for alarm condition. Additional features include hold function to lock in measurements, self-diagnostic error message, and status icons for measurement stability and low battery voltage. The IP67-rated housing features an easy-to-grip design and floats if accidentally dropped in water when sensor cap is on. Powered by four AAA batteries, the testers can operate up to 400 hours continuously. To conserve power, the unit will auto power-off after 8 minutes of nonuse.
-
Product
Traction Battery Drop Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
Traction Battery Drop Tester Relevant standards requirementsSingle Storage Cell Safety TestDropt testing steps：Charge the single storage cellaccording to 6.1.3Drop the positive negative terminals of the cellfrom the height of 1.5m to the concrete floor；Observe for 1hBattery Module Safety TestCharge the battery module according to the standard 6.1.4Drop the positive negative terminals of the battery from the height of 1.2m to the concrete floorObserve for 1h
-
Product
Battery Tester
G5.BT
-
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
Product
Car Battery Voltmeter
TE6-0607
-
Hangzhou Tonny Electric & Tools Co., Ltd.
Test the voltage on your car battery so you don't get stranded in the middle of nowhere! This Automotive Battery Tester measures the voltage of 12V or 24V automotive batteries by simply plugging into the cigarette lighter socket of your automobile. A 1.1-inch LCD displays the voltage and LED indicators display the power level.
-
Product
Digital Battery & Electrical System Analyzer w/Printer
726
-
*Accurate Battery & Electrical System Tester *Features programmed test for new Start/Stop Batteries 3 Testers in ONE! 1) 6 & 12 Volt Battery Tester + 12V Start/Stop Battery Test 2) 12 & 24 Volt Charging System Tester 3) Alternator-Starting-Charging System Tester *Wide Testing Range from 40 to 2,000 CCA *Built-in Printer - print the results for permanent service records *Removable/Replaceable Cable Set *Patented Dynamic Resistance Technology
-
Product
Battery Washing Tester, Battery Safety Testing
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's newly battery washing tester consisting of test chamber and washing chamber under test chamber. Moreover, it motorized rotary propeller mounted inside of test chamber and on internal wall of test chamber, drying system is mounted.
-
Product
6/12/24/36V Conductance Battery Tester
MBT300
-
Tests 6/12/24V lead acid batteries individually or in parallel and series battery packs. Displays battery or battery pack condition as % available capacity, rated capacity (CCAs), state of charge voltage, and good or replace status. Tests 6/12/24/36V starter and charging systems including starter draw, alternator and regulator output (loaded/unloaded), and diode ripple.
-
Product
Battery Tester
BAT-250-EUR
-
Is designed for one-handed,comfortable and reliable battery measurements. The uniquely designed tester offers an ergonomic slider and a v-shaped side cradle to better hold batteries in place during testing and a contoured case shape that fits neatly in your hand. Testing your batteries has never been easier.
-
Product
Multi Voltage Glow Plug Tester
4110
-
Peaceful Thriving Enterprise Co Ltd
*Auto switch off.*With CE Approval.*Voltage supply by 9V battery.*Tester probe/clip is easy to replace.*Rubber coating for tester protection.*Initialization for different testing probe/clip.
-
Product
Scienlab Battery Test System – Cell Level
SL113XA | SL100XA Series
-
The cell is the basis of any battery system and directly influences its function, performance and safety. Therefore, it is essential to test and characterize the cell at an early development stage. For this purpose, Keysight offers reliable test systems for precise and reproducible measurement results. The Cell Level Series (SL1002A, SL1004A, SL1007A, SL1132A and SL1133A) — also known as Battery Cell Tester — emulates sink and source for battery cells for automotive and industrial applications.
-
Product
Regular Battery Tester Models
-
The following are regular battery tester models for single-cell tests (coin cell/half cell/pouch cell/cylindrical cell, CT2001 & CT3001 Models) and supercapacitor test.
-
Product
Switch Mainframe
SW1002
-
Switch between voltmeter and battery tester while testing. 264 channels max. (2-wire) to 72 channels max. (4-terminal pair). Circuit design friendly for impedance measurements that minimize errors between channels (Effect: 0.01% f.s.*). For BT4560 100 mΩ range, R measurements, and a measurement frequency of 1 kHz. For OCV measurement, internal resistance measurement, and external potential measurement of battery cells. Measure battery modules up to 60 V DC.
-
Product
Laboratory Battery Tester With Integrated Chamber
-
Compact and versatile, our portable desktop solution integrates Arbin's advanced testing features.
-
Product
Battery Conductance Tester
FST-8000
-
Foresight Electronics Co., Ltd.
Profsional battery conductance tester for Lead-acid stationary (wet, flooded, gel, AGM, VRLA) battery cells/blocks, to measure actual capacity and aging for UPS, telecom, industrial, vehicle, solar or other applications' small and large battery banks.Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds.
-
Product
Advanced Battery Conductance/Electrical System Tester
PBT Series
-
Building upon the success of the PBT-100, the first battery conductance tester built for the professional technician's toolbox, the PBT-200 offers these additional capabilities: Shows available power in CCA in addition to condition and voltage. Bad Cell Detection. Advanced Starter Testing: Down arrow displays the captured low voltage from cranking the engine for simple starter analysis.
-
Product
Durable Hand-Held Battery Tester
6029
-
• Test 6 & 12 Volt batteries, alternators and starters• 125 Amp fixed load• Made in USA of US and Global Components
-
Product
Battery Tester
BT-100b
-
Konstar Electric Industrial Co., Ltd
Battery tester can test the car battery whether is ok, if the battery is bad or need charge or bad, the tester will give you the right check result, then can do the right plan for the battery before work.
-
Product
Battery Pack Drop Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Battery Pack Drop Tester Relevant standards requirement:Test object: battery pack and systemTest procedure: The test object is most likely to fall in the direction of actual maintenance or installation. If it is not possible to determine the most likely fall direction, fall in the Z-axis direction, and the battery pack will fall from the height of 1 m to the concrete floor and observe for 2 hours.Accept standard: The battery pack or system has no electrolyte leakage, fire nor explosion.
-
Product
CALKIT
612 IBT
-
This CALKIT enables you to recalibrate your ACT 612 Intelligent Battery Tester. Each CALKIT consists of replacement calibrated plug-in test leads, new replacement labels and instructions.
-
Product
Diagnostic Tools
-
Shenzhen Leagend Optoelectronics Co., Ltd.
leagend has 2-in-1 OBD II scanners with battery tester, OBD II trouble code diagnostic tools , OBD II memory savers, Bluetooth OBD II trouble code diagnostic tools, OBD II auto speedometers and auto trip computers.
-
Product
Electric Vehicle Battery Tester
-
The Electric Vehicle Battery Tester (EVT) is designed for testing traction batteries in electric vehicles or HEV batteries in hybrid electric vehicles. The EVT realizes the functions charge and discharge with freely programmable set values for current, voltage, power or resistance in test programs, as well as the registration of the corresponding measured data.
-
Product
Battery Cell Surge Tester
19311
-
The Chroma 19311 series battery cell surge tester is designed for testing the insulation quality between the positive and negative plates of the lead-acid battery cell. This is done by applying a high voltage surge/impulse before the electrolyte injection. Its output voltage can reach up to 6kV. It also has four terminal measurement and 200MHz sampling rate. The Chroma 19311 series has single channel (19311) and multi-channel (19311-10) tester.
-
Product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Tester
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
Product
500 AMP Carbon Pile Load Tester
710
-
The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.
-
Product
Gearbox Tester
Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
Tester
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
Receiver Tester
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, 1 kV Isolation
41-752A-113
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
