X Band
Radio band in the frequency range of 8.0 to 12.0 GHz and a wavelength 3.75 to 2.5 cm.
See Also: Radar
-
Product
Cable Assembly, Reveiver, 36", QuadraPaddle, 4 x 50-Pin FML D-Sub
540142020240
Cable Assembly
Cable Assembly, Reveiver, 36", QuadraPaddle, 4 x 50-Pin FML D-Sub
-
Product
SIMRC - 8 x 2 Matrix 1-Pole
1030-R-8-2-1-5/1D
Matrix Switch Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
24" Rackmount Drawer, Unshielded, 8.75"H x 20"D
DR-082420
-
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
USB4, USB 3.x, USB 2.0 and eUSB2 Protocol Decode/Trigger Software for Infiniium Oscilloscopes
D9010USBP
-
This application includes a suite of configurable protocol-level searches and software-based triggering specific to all USB standards. It is compatible with EXR-Series, MXR-Series, UXR-Series, S-Series, V-Series, and Z-Series Infiniium oscilloscopes. USB4 and USB 3.2 trigger and decode are not available for the EXR-Series, MXR-Series or S-Series oscilloscopes.USB4 and USB 3.2 trigger and decode are not available for the S-Series oscilloscopes. For detailed information on the decode and trigger settings, please refer to the datasheet. For assistance with using the applications, refer to the Infiniium help guide.
-
Product
C+L Band Broadband Light Source
S-103
-
ASE broadband source slot module of FOTS system can offer special function that is able to change optical output spectral feature variously, which is change optical output spectral feature variously, which is followed by user’s driving embedded pump LD freely. The output power of each pump LD is controlled separately by the program that is set up by user. In the case optimum ASE source output features such as wide broadband (> 80 nm @ -10 dBm/nm) and stable output power (< 0.02 dB) is needed, it is made up so that the provided Default mode along with User mode can be chosen and set up. More stable application of ASE source is possible through the combination of monitoring of ASE output power, alarm status and pump LD status with real-time optimal feedback. The embedded FPGA processor makes high speed control possible and enables monitoring and feedback routine operated stably.
-
Product
24" Rackmount Drawer, Unshielded, 10.5"H x 20"D
DR-102420
-
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Cable Assembly, Receiver, 20", QuadraPaddle to 2 x 78-Pin Female D-Sub Connectors
540112050140
Cable Assembly
Cable Assembly, Receiver, 20", QuadraPaddle to 2 x 78-Pin Female D-Sub Connectors
-
Product
19" Drawer with Writing Surface, Unshielded, 8.75"H x 30"D
DR-081930-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Cable Assembly, Receiver, 36", QuadraPaddle to 2 x 78-Pin Female D-Sub Connectors
540112050240
Cable Assembly
Cable Assembly, Receiver, 36", QuadraPaddle to 2 x 78-Pin Female D-Sub Connectors
-
Product
24" Drawer with Writing Surface, Unshielded, 8.75"H x 30"D
DR-082430-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
17" 1280 X 1024, VGA/DVI Interface, Ultra Slim Touch Open Frame Monitor
IDS-3117
-
17" 1280 x 1024 SXGA LCD panel with LED backlight for 20% power saving and environmental protection. -20°C~+60°C wide operating temperature support, 5-wires resistive touchscreen solution.
-
Product
4 X RS232/422/485, 2 X RS422/485, 8-Bit GPIO
MIOe-210
Single Board Computer
Full serial port: 4 x RS232 / 422 / 485, 2 x RS422 / 485±15kV ESD protectionOptional D-SUB connector or internal connectorProgrammable 8-bit GPIO interface
-
Product
24" Rackmount Drawer, Unshielded, 8.75"H x 30"D
DR-082430
-
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
19" Drawer with Writing Surface, Unshielded, 3.5"H x 30"D
DR-031930-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
4 X 10GbE + 16GE + 8GE Combo L3 Managed Ethernet Switch, -40~85℃
EKI-9728G-4X8CI
Ethernet Switch Module
16 x Gigabit RJ-45 ports + 4 x 10GbE SFP ports + 8 x Gigabit combo ports, L3 function : Static route , RIP v1/v2 , OSPF v2 , VRRP, SFP socket for easy and flexible fiber expansion. Management: SNMP v1/v2c/v3, WEB, Telnet, Standard MIB, Security:802.1x HTTPS,SSH and SNMPv3, Dual power input and 2 relay output.
-
Product
X.25 Adapters & XOT
FarSync X25 T4Ue
-
The FarSync X25 T4Ue PCIe card provides 4 high performance X.25 communications lines for Linux and Windows systems. A PCI bus version is also available.
-
Product
Telemetry Transmitter for FM with up to 3 Bands
LS-11-F
-
The LS-11-F portable FM test transmitter is designed for checkout and troubleshooting of telemetry receiving systems operating with FM modulation. For applications with any of the ARTM modulations (Tier 0, Tier I, or Tier II), please refer to the LS-11-M Data Sheet. Complete ground stations including the antenna with LNA, RF down-converter, IF receiver, bit synchronizer, and PCM decommutator can be tested and bit error tests performed. The design allows secure links to be tested with an external encryptor. The Test Transmitter contains an internal PCM Data Simulator and Pseudorandom patterngenerator that operates in a BERT mode. The device provides simulated clock and data (without transmitter enabled) and accepts external data for modulating the internal transmitter. Complete setup can be achieved locally through the keypad and two-line LCD display or remotely through the USB Interface. Operational parameters include the PCM format parameter database information (frame sync patterns, wavewords, etc…), pre-modulation filter selection, transmitter carrier frequency, transmitter deviation, and output power level. Output power can be selected from approx. -60 to +5 dBm in 5 dB steps. The Test Transmitter contains a LiFePO4 Battery (Lithium Iron Phosphate), which provides higher energy density at ¼ the weight of legacy lead-acid batteries. The unit also provides an internal battery charger and will operate for up to twelve hours on battery power having received on a full charge.
-
Product
CompactPCI 6U 16 slot P1-2s, P3-5l, 2 x P47
103CPCI616-7157
-
CompactPCI 6U 16 slot 64 bit Easyplug with 2 x P47 power connector, system slot right, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
15" 1024 X 768, VGA/DVI/HDMI Interface, Front IP65 Monitor
IDS-3315
-
Front IP65 for waterproof and dustproof, 15" XGA LCD panel with LED backlight for 20% power saving and environmental protection. -20 ~ +60 °C wide range operating temperature, 5-wire resistive and P-cap touchscreen solution or tempered smudge resistant protected glass.
-
Product
PXI/PXIe Wide Current Range Matrix Module, 6x4, 2-Pole, X & Y Loop-thru
42-514-002
Matrix Switch Module
The 40-514-002 (PXI) and 42-514-002 (PXIe) are low density matrices in 6x4 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
Product
2 X 1 SCSI Switch For Rack Mount Or Tabletop
MODEL SS1
-
The SS1 SCSI Bus Switch allows two hosts to share peripherals or one host to access either of two sets of peripherals. Each port may be SE, HVD or LVD. Switching from one port to the other may be accomplished: a. locally with the front panel switch, b. remotely with a momentary dry contact closure, or c. remotely via the RS-232 port. A software template for the RS-232 port is included in the User Manual. In all cases switching does not occur until "bus free."
-
Product
19" Drawer With Writing Surface, Unshielded, 5.25"H X 24"D
DR-051924-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock.
-
Product
Full Band (1200 ~ 1700 nm) Tunable Laser Source
CA9813
-
This specification describes and defines Advanced Lab Instruments CA9813 full band CW tunable lasers with applications to test and measurement equipment. It provides fast wavelength tuning, high power output, and high power stability. Advanced Lab Instruments tunable laser products support full-band, and other single-band operation. A full-band tunable laser is also available, covering 1200 ~1700 nm wavelength range, with seamless tuning.
-
Product
4 x 8 Two-Wire Matrix Module for DAQ970A and DAQ973A
DAQM904A
Matrix Switch Module
4 x 8 Two-Wire Matrix Module. 32 two-wire crosspoints with high switching voltage capability of up to 300 V and current capacity of up to 1 A.
-
Product
2 Pole 12 X 4 Low Thermal Relay Matrix Module
DP-cPCI-4113
-
A matrix is the most versatile switch topology. It is made up of rows and columns that connect any input to any output. With matrix switching system, it is easy to connect a number of instruments or sources to various test points of the UUT. The benefit of matrix switching is simplified wiring with which the overall test system can easily and dramatically change the internal connection paths without any manual intervention.DP-cPCI-4113 offers switching matrix in a single slot 6U sized cPCI module with flexibility to configure for 48 cross-points or 72 cross-points on factory selectable basis.
-
Product
VHF Band 1.0 Watt Amplifier With RF Bypass
-
Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.
-
Product
Linear Testfixture (Cassette Not Included), UTT 306 x 248 mm
MG-02
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for changeable cassette
-
Product
PXI 48 x SPDT Power Relay Module
45-157-001
Relay
The 45-157 SPDT Power Relay Module consists of 48 single pole changeover relays controlled by a PXI/CompactPCI interface. It is suitable for applications were conventional reed-relay based switching modules do not have sufficient voltage rating or current carrying capacity. All 48 contacts are electrically isolated from each other and are capable of switching resistive and inductive loads up to 2000VA at 240V AC.
-
Product
LGA 1700 Intel® 12th Gen. Core™ ATX Server Board with 4 x DDR5, 5 x PCIe(1 x Gen 5, 3 x Gen 4, 1x Gen 3), 7x USB3.2, 4xSATA3, Quad/Dual LANs, and IPMI
ASMB-788
Server Board
- LGA 1700 Intel® 12th Gen. Core™ i9/i7/i5/i3 processors with W680 chipset- DDR5 ECC/Non-ECC 4400/4000/3600 MHz UDIMM up to 128 GB- One PCIe x16 (Gen 5) and four PCIe x4 (3 x Gen 4 & 1 x Gen 3) slots- Triple displays - DVI-D, VGA, and HDMI 2.0 ports- Four SATA 3 ports and seven USB 3.2 ports- One M.2 2280 (PCIe x4)- Rackmount optimized placement with positive air flow design- 0 ~ 60 °C (32 ~ 140 °F) ambient operating temperature range
-
Product
PCI Single 22 X 8 Matrix 1 Pole Screened
50-512-021-S
Matrix Switch Module
The 50-510 series of matrix cards feature a wide range of selectable switching configurations (22x4,dual 20x4,22x8 and 44x4). Larger matrices may be constructed by Daisy Chaining the common signals from multiple PCI cards. For example four 44x4 Cards will form a 176x4 Matrix, a total of 704 crosspoints. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
