Wet Bulb
-
Product
Low Voltage Wet Sponge
-
Operates on a single 9-volt alkaline battery. Unit output voltage is 67.5 volts DC. This voltage makes the detector highly sensitive and accurate. Compact and light weight with no bulky battery packs allowing for non- destructive inspection of paints, epoxy paints and coatings 1-20 Mils.
-
Product
Hexagonal Wet Film Combs (Stainless Steel)
112 & 3236
-
These hexagonal precision formed stainless steel wet film combs are long lasting, reusable and supplied in a range of thicknesses measuring up to 3,000μm (120mils).
-
Product
General Purpose Reed Relays, Dry and Mercury Wetted
Series 80
-
General purpose dry relays - 0.1 inch x 1.0 inch grid. 5, 12, or 24 volt coils with optional diode.
-
Product
Coil Coating Wet Film Wheels
Elcometer 3230
-
The outer wheels are knurled to allow measurements to be taken on slippery coatings or on fast moving substrates.
-
Product
Wet Film Combs (Stainless Steel)
Elcometer 115
-
Four separate thickness ranges are available up to a maximum of 1,250μm or 50mils and are manufactured to an accuracy of ±5% of marked value or ±3µm (0.12mil), whichever is greater.
-
Product
General Purpose Reed Relays, Dry and Mercury Wetted
Series 89
-
Mercury wetted relays - 0.1 inch x 1.0 grid. As series 80 and 88 but with alternative pin configuration
-
Product
Dry Bulb Temperature Probe for WBGT
TP3207
-
Pt100 sensor temperature probe. Probe stem Ø 14 mm, length 140 mm. Cable length 2 metres. Equipped with SICRAM module.
-
Product
Plastic Wet Film Combs
154
-
Metric and Imperial values are on the same comb, 50 to 800μm on one side, 2 to 32mils on the other.
-
Product
Leaf Wetness Sensors
-
Campbell Scientific offers two types of leaf wetness sensors to measure the wetness of leaves: surface contact and electrical resistance. Surface contact sensors measure the electrical resistance of a water film on their surface. Electrical resistance sensors imitate the characteristics of leaves and measure the dielectric constant of their upper surfaces.
-
Product
LED Driver & Bulb Testing Instruments
-
Providing you the best range of Driver Testing Machine, Digital Power Analyzer, THD Power Analyzer, AC Production Tester, Smart QC Meter and Power Supply Tester with effective & timely delivery.
-
-
Product
Wet Sponge Pinhole Detection
-
Wet Sponge Technique: A low voltage is applied to a moist sponge. When the sponge moves over a coating flaw, liquid penetrates to the substrate and completes an electrical circuit, setting off the alarm. The wet sponge technique is suitable for measuring insulating coatings less than 500μm (20mils) on conductive substrates, and is ideal for powder coatings and other coatings where the user does not wish to damage the coating.
-
Product
Long Edge Wet Film Combs (Stainless Steel)
3238
-
Each comb has 24 measurement steps (teeth) providing a more accurate wet film thickness value.
-
Product
Wet Film Wheels
3230
-
By rolling the gauge through a wet coating, the centre wheel eventually touches the film. This point on the scale indicates the thickness.
-
Product
Dry Bulb Temperature Probe for WBGT
TP3207.2
-
Dry bulb temperature probe used for calculating the following indices: IREQ,WCI, DLE, RT, PMV, PPD, WBGT, SR and mean radiant temperature. Pt100 sensor.
-
Product
Punched Wet Film Combs (Aluminium)
112AL
-
The Elcometer 112AL, being punched from aluminium, is not as accurate as precision formed stainless steel wet film combs and has a shorter lifespan.
-
Product
Wet Oxidation TOC Analyzer
TOC-VWP
-
Phosphoric acid and the oxidant (persulfate) are added to the sample, which is heated under UV illumination to convert the TC in the sample to carbon dioxide. This carbon dioxide flows with the carrier gas via the dehumidifier into the NDIR sample cell. The area of the carbon dioxide peak signal is measured and this peak area is converted to TC concentration using a pre-prepared calibration curve.
-
Product
UV/IR Wet Bench Flame Detectors
SMC 3200/3300
-
The SMC 3200/3300 Series Flame Detectors utilize proven, stable UV/IR technology to continuously monitor for flames in wet bench and commercial applications. Due to its compact size, it is also used for installation in certain production equipment.
-
Product
Sealed Beam Bulb Testing System
H710019SSL
Test Platform
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
-
Product
In-line Wet Process Concentration Monitoring
-
CI’s family of wet process concentration analyzers (WetSpec line) offers cost effective solutions for in-line wet chemistry monitoring. These products range from conductivity and NDIR solutions for simple chemistries concentration measurement, to spectroscopic systems for measuring multiple constituents and residues in complex solutions. The main concentration monitoring application that are served by CI Semi’s products are cleaning (SC1, SC2…) etching (HF, BOE, MAI….) and photo resist strippers (EKC, ACT, Piranha….).
-
Product
In-plant Low Voltage Wet Sponge
-
Wet Sponge Holiday Detector for Plant or Stationary Operations is highly sensitive and accurate. A uniform coating of only one mil of paint or other non-conductive material over a metal surface is sufficient to repel a small current flow. If a pin-hole holiday is encountered, moisture from the sponge will seep into the hole and create a free path for electrical flow, activating the signal horn.
