Hall Sensors
-
Product
Linear Hall Sensor
-
The output of a hall effect sensor is a voltage which changes in proportion to the shaft extension. A constant voltage is required across the supply and ground wires of the sensor. The sensor consists of a Hall Effect element, and a shaft which houses a magnet. When the position of the sensor changes relative to the shaft, the change in magnetic field in the sensor results in a change in output voltage.
-
Product
Hall (Magnetic) Sensors
-
Small, compact axial and transverse Hall generators for measuring flux density. Available for use at cryogenic temperatures.
-
Product
Hall Sensor Board with I2C Interface
056-742
-
Version: +5V/60A +3,3V/60A +12V/90A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Hall Effect Sensors
-
A new range of sensors based on closed loop hall effect technology, for measuring and monitoring of e.g. secondary transformer overload or shortcircuit detection, DC link from ground fault and overload, motor overload.
-
Product
Split Core Hall Effect DC Current Sensor
CYHCT-C2TC
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a split core and a high galvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
Hall Effect Sensors
906
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Bi-directional option 906B
-
Product
Hall Sensor Board with I2C Interface
050-279
-
Version: +5V/90A +3,3V/25A +12V/60A +12V/60A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Hall Effect Sensors
-
The Mors Smitt transducers are used to measure high currents in rolling stock and trackside applications. High currents are converted linearly to low power signals.
-
Product
Closed Loop Hall AC/DC Current Sensor
CYHCS-SH
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can beused for measurement of DC and AC current, pulse currents etc. The output of thetransducer reflects the real wave of the current carrying conductor.
-
Product
Open Loop Current Sensor
C03 30A
-
The C03 offers efficient and precise sensor solutions for direct, alternating and pulsed currents in industrial, commercial and communication systems. It consists of three main components: an accurate, linear Hall sensor with low temperature drift, a flux collector and a transformer. It is characterized by a very low resistance and thus lowers power loss and temperature drift - for optimal performance.
-
Product
AC / DC Current Probe, 100 MHz, 30 Arms
N2783B
Oscilloscope Probe
The N2783B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 30 Arms continuous.
-
Product
Closed Loop Hall AC/DC Current Sensor
CYHCS-D8
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current in the carrying conductor.
-
Product
Speed Sensors
-
DHE (Differential Hall Effect) sensors give an output when subjected to a changing magnetic field. The field is set up by a magnet inside the sensor body and changes when ferromagnetic teeth are passed beneath the sensor (no magnets are required in the target). To improve noise resistance, the sensor has two Hall effect elements and only responds to changes in magnetic field strength corresponding to tooth passing frequencies above 15Hz. As each tooth passes the sensor, the digital state of the output changes.
-
Product
Closed Loop Hall Effect Current Sensors/Transducerswith Rectangle Windows
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used formeasurement of DC and AC current, pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
Product
Closed Loop Precise Hall AC/DC Current Sensor
CYHCS-LF
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for accurate measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
Quadrature Sensor
-
SPECTEC Innovative Sensor Solutions
DIGISPEC Hall Effect Quadrature Sensors provide two digital output signals, 90º out of phase to each other, detecting speed (down to true zero speed) and direction of rotation of gear teeth and ferrous targets. Gear teeth as small as module 0.10" wide can be sensed. Standard output is provided from a 2.2kOhm internal pull-down resistor to a collector, which can sink 25 mA. Open collector can be provided. Output is protected against reverse voltage.
-
Product
Hall Effect Gear Tooth Sensors and Custom-Made Target Wheels
-
ChenYang Technologies GmbH & Co. KG
ChenYang Technologies GmbH & Co. KG supplies various kinds of Hall Effect Gear Tooth sensors (CYGTS101DC, CYGTS99, CYGTS211, CYGTS212, CYGTS99-198 etc.) for speed measurement with applications to machines, equipments, motorcycles, automobile industry and instruments etc. We are specialised in design, development and production of Hall-effect sensors and can offer also custom Hall sensors for your special applications.
-
Product
Speed Sensors
-
Variohm supply differential hall effect speed sensors for use in motorsport applications. We have two different designs but both offer very high performance.
-
Product
Split Core Hall Effect DC Current Sensor
CYHCT-C2TV
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a split core and a high galvanic isolation between primary conductor and secondary circuit. It can be used for measurement of DCcurrent etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
Proximity Sensors
-
Premier Electrosystems is an esteemed name in the manufacturing of inductive proximity switch, photo sensors, capacitive sensors, magnetic sensors, hall effect sensors, analog sensors, encoders, infrared sensors, etc. with NABL calibration certificate
-
Product
AC / DC Current Probe, 10 MHz, 150 Arms
N2781B
Oscilloscope Probe
The N2781B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 150 Arms continuous
-
Product
Hall Effect DC Current Sensor
CYHCT-WS3
-
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-WS3 is a Hall Effect sensor for the measurement of DC current. The sensor has agalvanic isolation between the high power primary conductor and the secondary electronic circuit and withdifferent output signals and different power supplies.
-
Product
Wireless Connectivity AC / DC Clamp Meter with 6000 count / NCV / SPT / 600A AC / DC Current
MS-W366D
-
This is a external wireless connectivity Digital Clamp Meter integrated with AC / DC hall effect sensor / 6000 Count, True RMS, auto and manual measurement.
-
Product
N2782B AC / DC Current Probe, 50 MHz, 30 Arms
N2782B
High Current Probe
The N2782B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 30 Arms continuous.
-
Product
Vehicle Actuator Tester
7651
-
Peaceful Thriving Enterprise Co Ltd
This device is design to test electronic components actuate by magnetic field or electronic magnetic field. Devices like actuator, ignition coil, AC generator, indoor air blower, valve controller EGR (exhaust gas control), injector, spark plug, relay and hall effect sensor can be tested.
-
Product
AC / DC Current Probe, 2 MHz, 500 Arms
N2780B
Battery Probe
The N2780B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 500 Arms continuous.
-
Product
Gaussmeter (Magnetometer)
NOVOTEST MF-1
-
Portable Gaussmeter (Magnetometer) NOVOTEST MF-1 is equipped with a Hall sensor to measure the magnetic induction in the following units: Gauss, Tesla, Amps/meter.
-
Product
C Series Frequency Input Module
Input/Output Module
The C Series Frequency Input Module is designed to acquire isolated frequency inputs from magnetic pickup sensors, variable reluctance sensors, Hall effect sensors, and other transducers with a frequency output. Additionally, the C Series Frequency Input Module provides isolation, configurable thresholds, selectable filtering, and embedded counter measurement logic. These measurements can be synchronized with other frequency, analog, digital, and counter measurements in a single acquisition.
-
Product
Hall Effect Proximity Switches/Sensors
-
ChenYang Technologies GmbH & Co. KG
A Hall Effect proximity switch is a non-contact electronic switch, which consist of a permanent magnet or ferromagnetic part as trigger intermediary and a Hall Effect sensor IC. The Hall sensor IC detects the change of the magnet field when the permanent magnet comes in the close proximity to it and generates an electric signal. This signal is amplified and rectified to control the output signal of the switch.
-
Product
Hall Sensor Board with I2C Interface
055-013
-
Version: +5V/5A +3,3V/5A +12V/5A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
