Hall Effect Sensors
-
Product
3U OpenVPX Sensor Interface Unit
SIU32S
Sensor Interface Unit
The SIU32S is a highly configurable Modular Open Systems Approach (MOSA) rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, processing, communications and Ethernet switching. The SIU32S leverages NAI’s Configurable Open Systems Architecture™ (COSA®) 3U boards and smart function modules to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
Hall Effect Probes
-
Magnetic Instrumentation manufactures Hall Effect Probes in a wide range of styles and sizes. Probes are supplied with magnetic, electrical, temperature stability and calibration data for each measurement range.
-
Product
Peak And Average Power Sensor, 50 MHz - 6 GHz, 5MHz Bandwidth
E9323A
Power Sensor
The E9323A power sensor has a 5 MHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on W-CDMA wireless formats such as cdma2000.
-
Product
Hall Effect Measurement system
HMS-3000
-
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
Product
Thermocouple Power Sensors
N8481B
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
3U cPCI Sensor Interface Unit
SIU31
Sensor Interface Unit
NAI's SIU31 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communications, Ethernet switching, and processing. The SIU31 uses one NAI field-proven, 3U cPCI board to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-to-Mission."
-
Product
USB Power Sensor, 9 kHz to 6 GHz
U2004A
Power Sensor
Fast and simple setup with plug-and-play USB connectivity. Eliminates the need for a separate power meter.
-
Product
Air Sensor
E1738A
Environmental Sensor
The Keysight E1738A environmental sensor measures air pressure, temperature and humidity. The sensor detects and automatically compensates for operating environment changes when used with the 5530 Laser Calibration System. The result is improved overall system accuracy.
-
Product
Hall (Magnetic) Sensors
-
Small, compact axial and transverse Hall generators for measuring flux density. Available for use at cryogenic temperatures.
-
Product
Power Converter Test Solution for HEV/EV and HEMS
EV1003A
Power Sensor
The hybrid-electric and electric vehicle (HEV/EV) market has been growing rapidly. The addition of these vehicles in the automotive market brings with them new challenges in design and manufacturing. Probably the most noticeable change is the addition of high-voltage, high-power batteries to a platform that is traditionally 12 volts. Hybrid electric and full electric vehicle batteries are 300 volts and higher. These high voltages bring with them additional costs and risks.
-
Product
E-Series Average Power Sensor
E9301A
Power Sensor
Measure the average power of all modulation formats Wide dynamic range (-60 dBm to +20 dBm) and frequency range 10 MHz to 6 GHzHigh maximum power specification Low SWR for reducing mismatch uncertainty Calibration factors linearity and temperative compensation data stored in EEPROM Fast measurement speeds (up to 400 readings per second with the Keysight E4416A)Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
E-Series Peak And Average Power Sensor, 50 MHz To 18 GHz
E9327A
Power Sensor
The E9327A power sensor has a 5-MHz video bandwidth and is ideal for time-gated peak, average, and peak-to-average ratio power measurements on W-CDMA wireless formats such as cdma2000.
-
Product
DC/10 MHz – 33 GHz USB Thermocouple Power Sensor
U8485A
Power Sensor
The U8480 series is the fastest USB thermocouple sensor in the world without compromising the best in class linearity of the legacy 8480/N8480 series thermocouple sensors, all in a compact USB based form factor.
-
Product
E-Series Average Power Sensor
E9300B
Power Sensor
Measure the average power of all modulation formats Wide dynamic range power measurements from -30 dBm to +44 dBm Frequency range 10 MHz to 18 GHzLow SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
Thermocouple Power Sensors
N8486AQ
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
Current Probe With Hall Effect Technology
CP 35
-
The CP 35 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
Product
Resistivity and Hall Effect
-
The Resistivity System allows the user to make Resistivity and Hall Effect measurements in the range of to M. Samples are mounted on special platforms inside the VTI with contacts made to the sample according to the customer's requirements.
-
Product
10 MHz To 67 GHz USB Wide Dynamic Range Average Power Sensor
U2057XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
Hall Effect Measurement system
HMS-5300
-
Variable temp : 80K ~ 350K (model#: AMP55T ) - HMS-5300 can be compatibly used with both low temp magnet kit (model# : AMP55T) and high temp magnet kit (model# : AHT55T3, upto 300dC). - Below image is to show model# HMS-5300 + AMP55T, for low temp.
-
Product
Hall Effect Measurement system
HMS-5000
-
Constant current source + Van der Pauw method terminal conversion system
-
Product
Wideband Power Sensor, 50 MHz To 18 GHz
N1923A
Power Sensor
The Keysight N1923A peak power sensor provides peak, peak-to-average ratio, average power, rise time, fall time, maximum power, minimum power and statistical data of peak signals.
-
Product
Hall Effect Systems
-
The MeasureReady™ measurement controller is a revolutionary, all-in-one Hall analysis instrument that delivers significantly higher levels of precision, speed, and convenience to researchers involved in the study of electronic materials.
-
Product
POF Ext Ø 1,5mm 600mm, from 5mm Lens to VPC ITA Contact
YAV90CLR10
LED Sensor
The probes for sensing LEDs, P/N YAV90CR10 feature an Optical Head to correct missalignment errors in X and Y axis. As a result, the relative read out will oscillate less tan 5% with a missaligment of + 0,5 mm Offset
-
Product
Dual Channel, ±12 V, 100 MHz, 40 NA – 1 A
CX1102A
Power Sensor
The CX1102A dual channel current sensor is a dedicated accessory for the CX3300 series mainframe and features wide dynamic measurement ranges due to the simultaneous capture technology.
-
Product
Hall Sensor Board with I2C Interface
056-742
-
Version: +5V/60A +3,3V/60A +12V/90A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Hall Effect Measurement System
RH 2010
-
The RH 2010 Hall Effect Measurement System has been designed for high flexibility and ease of use as a standard system for quick routine control measurements as well as for sophisticated temperature dependent Hall measurements for material research.
-
Product
Hall Sensor Board with I2C Interface
050-279
-
Version: +5V/90A +3,3V/25A +12V/60A +12V/60A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
10 MHz to 40 GHz USB Wide Dynamic Range Peak and Average Power Sensor
U2064XA
Power Sensor
The Keysight U2064XA is a fast, accurate and wide dynamic range 10 MHz – 40 GHz USB peak and average power sensor.
-
Product
USB Hall Probes
-
MAGNET-PHYSIK Dr. Steingroever GmbH
The USB Hall probe is simply connected to a computer and operated using easy-to-understand software. No additional measuring device is required to measure the magnetic field strength. You can download the "USB Teslameter" software for Windows here. A Linux version is available from us on request.
-
Product
Field Effect Rectifiers
-
ST field-effect rectifier diodes (FERD) help improve designs with new versions focusing on trade-off upgrades. Field-effect rectifier diodes belong to our STPOWER family. The design of the FERDs has allowed both a decrease in the voltage drop and a decrease in the leakage current temperature coefficient. As a result, the runaway safety margin is improved and maybe beyond the typical safety margin of Schottky barrier diodes.
