Control Systems
-
Product
3U CompactPCI Multi-Function I/O Board
CPCI-AD32
-
The CPCI-AD32 is a 3U CompactPCI multi-function I/O board. The CPCI-AD32 offers 32 channels of 16 bit A/D, two 16 bit D/A, 16 digital I/O, counter / timers.There is a local 60 Mhz TMS320C31 DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-AD32 is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
Product
Slip-Ring Motor Starting Panels
Rotor Starter
-
The Slip-Ring Motor Starters are based on the series of resistors that are applied to the rotor circuit to control the speed/torque characteristics of the motor. Rotor starters are mainly used for the motor starting applications requiring high-starting torque like loaded belt conveyors in mining industry. By external resistors, it is possible to shift the motor maximum (break-down) torque up to starting torque point for motors under heavy loads during start-up. The resistors are splitted into some steps and controlled via contactors by motor starting control system. As the motor speed increases, the external rotor resistors are eliminated by shorting contactors until all external resistors are shorted out.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 255 Ohm With SPDT
50-293-113
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Vapor Source Mass Flow Controller With Viscous Choked Flow
-
The 1150C Vapor Source Mass Flow Controllers are pressure based measurement and control systems designed to meter and control vapor from low vapor pressure liquid and solid sources directly, without the need of a carrier gas using viscous flow through a choked orifice.
-
Product
14-Slot Combination PXIe Chassis
GX7100e Series
-
The GX7100e Series are 14-slot combination PXIe chassis that accommodate a 3U PXIe embedded controller or a MXI express controller as well as 3U & 6U PXI / PXIe insruments in 4U of rack space. The GX7100e’s unique format includes seven 6U slots and seven 3U slots arranged horizontally to reduce the overall size of the chassis, providing the versatility and high-density necessary to address many PXI / PXIe applications and requirements. The backplane architecture supports Gen 2, 4x4 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7100e offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
-
Product
Automated Visual Control System for Canned Food in Glass Containers
-
The system is designed for visual quality control of food packaging products. The level of filling the jar with the product, as well as its closure, is monitored. During the development of the system, smart cameras from Sick were used, but a special illumination of our design was used to improve the image quality.
-
Product
AeroEngine Test Cells
-
A tec is a leading provider of jet engine test cells and flight component support. We provide our customers with high quality, superior value maintenance facilities and equipment for the testing of all types of turbine engines. We excel in both the design and construction of new facilities and the technological refreshment and sustainment of legacy systems. The Atec companies operate worldwide with new test cells, test cell modifications, engine test adapters, ADAQ™ control systems, support equipment, test benches, utilities subsystems, site surveys, repairs and training, and Master Service Agreements (MSAs).
-
Product
PCIe-8361 , x1 Gen1 PCI Express Host, 208 MB/s, 1-Port, Copper Cable MXI-Express Device for PXI Remote Control
779504-01
-
The PCIe‑8361 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI Express slot. The PCIe‑8361 remote controller provides a x1 PCI Express link over a copper cable to the PXIe‑8360 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
Product
Digital System Controller
SC-20
-
The SC-20 system controller is capable of executing an entire coating run with the push of a single button. The backlit LCD display provides an easy way to monitor the coating and system status while running. The SC-20 can communicate not only with other Eddy process controllers, but with most OEM controllers as well. This makes it a perfect candidate for system upgrades as well as new builds. Noise protected circuitry coupled with continuous logic software ensures the process will be controlled and monitored throughout the whole process.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm
50-294-021
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
3U PXI-E System Controller
PX32101
-
LinkedHope Intelligent Technologies Co.,Ltd.
PX32101 is a 3U PXI-E system controller based on the newest Intel® Haswell platform. It is designed to provide comprehensive and reliable system controller to support hybrid PXIe-based systems for multiple environments test and measurement applications.Hybrid PXIe-based systems are often required to complete independent diversified complex testing tasks on the PXI test platform. PX32101 provides rich interfaces: 4 USB2.0 / 3.0 for peripheral connectivities; UART for communication or control equipment; dual 1000Base-T Ethernet, one port for LAN connection and the other one for the control of the next generation of LXI instruments.PX32101 can support 4 x4 or two PCIe x8-link, and up to 16GB / s system bandwidth. The ExpressCard 34 expansion slots on the front panel allow users to expand the system modules flexibly. If you install a hybrid multi-slot backplane in the system, then various standard PXI-E and PXI / CPCI peripheral cards could be fitted.In a multitasking environment, PX32101 processor is able to complete multiple tasks independently. The CPU and memory chips soldered with PCB increase reliability performance in shock and vibration environments. Combined with a variety of instrument control interfaces and reliable mechanical & electronic design, PX32101 can meet your hybrid PXIe-based testing for system application requirements perfectly.
-
Product
Electromagnetic Resonance High Frequency Fatigue Testing Machine
PLG Series
-
Jinan Testing Equipment IE Corporation
The series of electromagnetic resonance fatigue testing machines are used for fatigue tests of metal materials and components under tension, compression or reversal loads. If relevant grips are provided, three-point bending test, four-point and circle test, gear wheat, bolt, connecting rod, roller chain, crackle expanding test can be available. The series of electromagnetic resonance fatigue testing machines feature an optimized design and a rational structure. The automatic controlled system adopts an advanced and wide-pulse-control system and a new-type of power amplifier to improve the reliability of the electric system. The electromagnetic resonance fatigue testing system is with high efficiency, easy and non-stop shake, low energy consuming, accurate control, and small fluctuation.
-
Product
Touch Posi-Control System V2
DPC
-
The position control torque arm system helps manufacturers detect and eliminate costly screw-fastening errors during the assembly process. This position control system is designed to reduce the risk of improperly fastened screws, ensuring that every screw is in the correctly tightened in the correct sequence. A good tightening sequence ensures that an even preload distribution is achieved in the joint. Using a position control system is like putting the eyes and ears of a quality control manager where they are needed most - right on the assembly area.
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 1.5K
40-265-402
-
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 1.5Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 350
40-265-014
-
This module simulates the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems.
-
Product
Locomotive Interface Gateway
LIG
-
Locomotive Interface Gateway (LIG) is a network communications and interface device that provides locomotive control-system data to third-party applications. The LIG is designed with an Open Message Interface which allows applications to access control-system data while providing locomotive system isolation to ensure the control system is not adversely impacted by third-party applications. The real-time parameters available from the LIG can be used to perform real-time health and status monitoring of a locomotive as well as real-time assessment of locomotive operator performance.
-
Product
High Output Simulators
-
The Abet Gen II optical design, patent pending, dramatically increases the percentage of photons reaching the work plane.All electronics are packaged in the lamp house – no clutter of high power cables to deal with. A digital shutter timer allowing both manual and external control is included with every unit.Standard maintenance, lamp or filter replacement, does not require any tools.Locking indicator dials on all the system controls provide for a reproducible and stable setup.
-
Product
Physical Layer Switching Systems for copper LAN, WAN, DSL, Telco apps with RJ style connectors.
RJ Series
-
The RJ Series of computer controlled switching systems are designed for physical layer switching of multiwire signals on RJ style connectors. Since the system uses mechanical relays it acts exactly like a piece of cable which makes it perfect for testing networks without altering the signals or regeneration. These systems are typically used for Ethernet LAN 10BaseT through 1000BaseT, DSL including ASML through GFAST, CAT5 through CAT6A cable testing, USB up to 2.0, RS232, RS422, RS485 up to 8 wire at 20 Mbps and many other applications switched over RJ45 connectors up to 8 wires. They may also be used as lab automation switches, network testing switches, patch panels, network redundancy switches or any number of physical layer applications.
-
Product
Industrial Standby Battery Monitoring Systems
-
Batteries are the power storage medium for all Power Rectifier and UPS Systems. Modern Rectifiers and UPS control systems generally supply the user with only a summary of the condition of the associated power systems, however Battery Monitoring systems specifically measure, record and analyse the individual cell and battery module parameters in detail.
-
Product
AGH Hydrophones
-
Teledyne Marine AG Geophysical Products
Primarily used with seismic source firing and control systems where the hydrophone is operating in close proximity to, or in the high pressure explosive force field of a seismic source.
-
Product
ORIGAMI femtosecond lasers
-
Our all-in-one, single-box, microjoule femtosecond lasers. The laser head, controller, and air-cooling system are all integrated into one robust package so small it fits in your hand luggage.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm
50-293-012
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Systems Integration for Circuit Card Assembly
-
Teledyne Advanced Electronic Solutions integrates CCAs and other sub-assemblies, cables and fabricated parts into system modules shipped directly to customers for integration into their products.- Box Build: custom built to order system solutions- High complexity box assemblies and subsystems- High frequency RF box assemblies and subsystems- Full functional RF testing up to 26 GHz (K band)- Multi-level systems integration – build and test modules and CCAs and integrate into higher level assemblies- Custom cell design for customer subsystems- Special bonding processes including thermal management and vibration- Robust torque and FOD control programs- System level testing including functional, vibration and thermal- Complex harness fabrication and integration- Fiber-Optic and RF waveguide integration and testing- Large system capacity in excess of 200 lbs.- Configure to order – Integrate different options, firmware, configurations, etc across a single order as required
-
Product
Vapor Source Mass Flow Controller With Viscous Laminar Flow
-
The 1152C Vapor Source Mass Flow Controller is a pressure-based measurement and control system designed to meter and control vapor from low vapor pressure liquid and solid sources directly, without the need of a carrier gas. The 1152C consists of a fixed flow element and two capacitance manometers for flow measurement, with a proportioning solenoid control valve for flow control.
-
Product
Data Acquisition & Control Systems
Series 6000
-
An innovative and fully integrated modular transducer conditioning, acquisition and control system, the Series 6000 has unparalleled performance and accuracy. From two to many thousands of channels, high & low speed, analog & digital, Series 6000 acquires measurement data from virtually all types of sensors and is fully customizable to fit the needs of any test facility. Large & small, AC & DC powered enclosures are available for nearly any test environment. Analog and digital I/O modules condition, amplify, filter and digitize signals from transducers. Turnkey and/or API software is available, helping facilities get up and running quickly.
-
Product
Rotary Joints
-
In addition to space applications, CAES rotary joints are used on many different platforms throughout the world, including ground-based and airborne advanced military radar, telemetry and air traffic control systems.
-
Product
PXI Bus Expanders
MXI-4 Series
-
The MXI-4 PXI Bus Expanders allow direct control of PXI systems from any PCI slot in a desktop computer or server. MXI-4 interface cards can also be used to link multiple PXI chassis. MXI-4 technology utilizes a high-bandwidth link that is transparent to software applications and drivers, therefore providing the ability to use high performance desktop computers or servers to control PXI systems.
-
Product
Automated Visual Quality Control System for Lid Assembly
Angara-form
-
The automated visual inspection system is designed to identify and reject covers that have defects that have arisen during industrial production, as well as visible defects in the form of black dots or dirt on the surface of the cover.
-
Product
Explosionproof Actuators and Control Systems
Schischek HVAC Solutions
-
Schischek electric explosionproof products for heating, ventilating and air conditioning (HVAC) for industrial and offshore applications. Developed in conjunction with other control equipment to produce modern, reliable and proven explosionproof products utilising the latest technology.
-
Product
Nano-Position Sensors
-
ZYGO nano-position sensors are widely used in closed-loop motion control systems like photolithography and semiconductor inspection tool stages, as well as for deformable optical systems. We have pioneered innovations in the displacement and position sensors for over 30 years, and we work closely with applications requiring the highest precision and reliability. Our team of applications experts is ready and able to help you tackle your position metrology needs.
