Control Systems
-
Product
Test Automation System for Brake Testing
STARS Brake
-
STARS Brake is an integrated automation, data acquisition and control system platform that provides a comprehensive application functionality in a single, powerful environment. STARS Brake is designed to address the needs of a wide range of brake testing applications from component development to final component and system validation. It offers users a level of flexibility and openness that enables thorough investigations of brake systems.
-
Product
Bluetooth Enabled Signal Conditioners I/O Modules
microBlox
-
Acromag's microBlox uB Series I/O modules offer a compact, high-performance solution for interfacing sensors and field devices with data acquisition systems. uB signal conditioning modules are ideal to isolate, filter, convert and amplify a wide variety of signal types for test, measurement and control systems. Just plug uB modules into 4, 8, or 16-channel backpanels in any mix for a high-density analog I/O interface. Channel-to-channel isolation provides optimal noise and surge protection from ground loops, spikes, and high common mode voltages.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm
50-294-021
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Resistor Card 6-Channel, 24-Bit, 0 To 16M Ohm
50-295A-121-6/24
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Digital Gauge Pressure
ZET 7112-I VER.2
-
ZET 7112-I VER.2 digital gauge pressure (open membrane) is used for fast and simple pressure measurements and measured values data transfer in digital format via CAN 2.0 interface. ZET 7112-I VER.2 digital gauge pressure (open membrane) is intended for integration into various technological processes automated control systems. Open membrane type enables pressure meters operation in viscous, pasty and rapidly polymerizing environments.
-
Product
2-CH MIL-STD-1553A/B Bus Simulator Module
1553 WA73A-455
-
The WA73A-455 MIL-STD-1553A/B Bus Simulator Module allows a system controller in an ATE system to communicate with and test devices that conform to the MIL-STD1553A/B data bus used in military aircraft and communications systems. Each of the WA73A-455's two channels operate as two separate and independent channels with their own VXIbus logical address, interrupts, and complete set of controls and indicators. As a result, each channel of the WA73A-455 is truly an independent instrument, and, therefore, individually programmable.
-
Product
PXI Signal Insertion Switch Module
Switch Module
PXI Signal Insertion Switch Modules, also known as fault insertion units (FIUs), provide a set of feedthrough channels, which make the switch transparent to the system when closed. You can open or short these channels to one of two fault buses, allowing you to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI Signal Insertion Switch Module can validate the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs). You can also use the FIU models for hardware-in-the-loop (HIL) applications and electronic reliability tests.
-
Product
MIMO Vibration Control Overview
-
MIMO Testing has gained a huge momentum in the past decade with the development of multiple shaker table systems, the availability of Multiple-Input Multiple-Output (MIMO) controllers, and the readiness of the standards (e.g., Mil STD 810G method 527 and IEST DTE 022 working group recommendation). The Multiple-Input Multiple-Output (MIMO) Control System includes the following:
-
Product
Single Phase Universal Protection Relay Test Set
S100A
-
S100A is the Universal Single Phase Protection Relay Test Set with 1*100A and 3*150V output, local control system for basic relay testing with manual operation.
-
Product
Semi-Automatic Kjeldahl Analyzer
LD-LKA-A20
-
LKA-A20 is a semi-automatic Kjeldahl analyzer having intelligent design. It is equipped with 4.3" LCD screen, automatic fault detection system and intelligent audible and visual alarm system. With features such as automatic alkali liquid quantification and filling, automatic boric solution quantification and filling, intelligent cooling water control system and emergency stop operation, it is a safe and reliable instrument.
-
Product
Railway Solutions
-
Highly reliable rugged electronics for rolling equipment and rail infrastructure. Standard and Custom-made platforms: Security Display computers, Touch Screen Panel PCs, Tablet computers, Onboard Automatic Control system, Digital Video servers, Intercommunication equipment.
-
Product
Systems for Vibration Monitoring and Diagnostics
-
*Reliable permanent vibration monitoring according to DIN ISO 10816*Cost effective real-time vibration monitoring for machine protection*Increase availability and reliability, reduce maintenance costs and ensure quality*Compact field units and modular control cabinet systems*Analog output and switching output for alarm function
-
Product
Solar Simulators
Sun 2000 Class A
-
The Abet Gen II optical design, patent pending, dramatically increases the percentage of photons reaching the work plane.All electronics are packaged in the lamp house -no clutter of high power cables to deal with. A digital shutter timer allowing both manual and external control is included with every unit.Standard maintenance, lamp or filter replacement, does not require any tools.Locking indicator dials on all the system controls provide for a reproducible and stable setup.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm
50-294-034
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm
40-294-011
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 1k
50-265-204
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm
50-294-032
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Digital Vibration Control System
DSC-98Smart
-
DCS-98Smart digital vibration control system is the high cost effective vibration controller introduced as the most newest version of DCS series. This system demonstrates as high performance as DCS-98000MJ, yet it has a feature of the cost effectiveness, aiming the rapid spread among the quality evaluation industry. It, thus, shall continue the better quality vibration control for any application than ever.
-
Product
Gas Detectors
-
Shenzhen Graigar Technology Co.,Ltd.
A gas detector is a device that detects the presence of gases in an area, often as part of a safety system. This type of equipment is used to detect a gas leak and interface with a control system so a process can be automatically shut down.
-
Product
SparkFun Humidity And Temperature Sensor Breakout
Si7021
-
The Si7021 is a low-cost, easy-to-use, highly accurate, digital humidity and temperature sensor. This sensor is ideal for environmental sensing and data logging and perfect for build a weather stations or humidor control system. All you need are two lines for I2C communication, and you’ll have relative humidity readings and very accurate temperature readings as a bonus!
-
Product
Smart Touch Computer Series
-
ADLINK’s Smart Touch Computer (STC) series is ideal for human–machine interface (HMI) applications in food and beverage, pulp and paper, textile, printing, word processing, and other industries. These standalone full-function panel PCs are designed for optimized production control and system monitoring, offering scalable performance, customizability, and I/O expansion. With an industrial-grade, robust construction, and slim design, The all-in-one STC Series is designed for extended operation, allowing manufacturers to obtain time-sensitive sensor data and easily monitor and control manufacturing processes.
-
Product
CT / PT Analyzer
CTPTA-504
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
UDEY ‘CTPTA-504 is a comprehensive CT and PT analyzer. It’s constant voltage and current is highly stable. DSP system controls the constant voltage and current source output and amplitude. This source generates AC of 0-125V and or DC of 0-0.5A current to sample CT. The DSP system besides controlling the sources, also samples data and communicates with the internal computer. Display screen is large LCD with touch pad. The analyzer is highly accurate with high noise immunity and is very user friendly.
-
Product
R37F-37M-1, 37-pin Female to Male Ribbon I/O Cable, 1m
779195-01
Ribbon Cable
37-Pin Male IDC to 37-Pin Female D-SUB, I/O Ribbon Cable - The R37-37 is an unshielded ribbon cable for use with PC-based PC-based measurement and control systems featuring CompactDAQ Chassis.
-
Product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
Fault Insertion Unit
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
Vibration Control
-
m+p VibControl vibration controllers for advanced vibration control and shock testing from 4 to hundreds of input channels are used by many of the leading environmental test laboratories throughout the world. The endusers appreciate the intuitive operation, the extensive analysis and reporting functions, the numerous upgrade possibilities and, of course, the excellent stability and high quality level of the m+p vibration control systems. Applications range from normal to very extreme conditions, and also include rough transportation circumstances.
-
Product
Automatic Kjeldahl Nitrogen Analyzer
DRK-K616
-
Shandong Drick Instruments Co., Ltd.
The DRK-K616 Automatic Kjeldahl Nitrogen Analyzer is a fully automatic distillation and titration nitrogen measurement system designed based on the classic Kjeldahl nitrogen determination method. The core control system of DRK-K616, as well as the automatic machine and spare parts for perfection, create the excellent quality of DRK-K616.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 4.09k Ohm
40-294-023
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Superior Electromechanical Universal Testing Machine
WDW-S Series
-
Jinan Testing Equipment IE Corporation
WDW series computer control electromechanical universal testing system for tension,compression, flexure testing is designed according to ASTM, ISO, DIN, EN standards etc.. The electromechanical universal testing system for tension,compression, flexure testing is computer-controlled and precision. Our electromechanical universal testing system for tension,compression, flexure testing is widely suitable for metallic and nonmetallic materials for tension, compression, bending, shearing and low cycle test. The electromechanical universal testing machine features high precision, high stability and high reliability. Graph, test result display, data processing and printing can be done easily by its PC system and printer. Completed with modulus for metal, spring, textile, rubber, plastic and other material test, the electromechanical universal testing system for tension,compression, flexure testing is widely used in many fields such as industry factories, research and development, test institutes and training centers etc. WDW-S series superior materials testing systems adopt robust load frames, precise load weighting system, advanced measuring and control system, and intuitive modular application software. Configured with wide range of accessories for applications, the materials testing systems can provide the best testing solutions for your individual application needs. With 20 years’ experience of materials testing industry and based on abundant application knowledge, we are completely capable of configuring the best solutions and more accurate testing systems for the manufacturers involved in load frame, core measuring and control elements, software package, grip/fixture that based on their specified test application and other requirements.
-
Product
Multicore Digital Signal Processor
SI-C667xDSP
-
Sheldon Instruments offers a complete portfolio of hardware products for a wide spectrum of real time applications in measurement and digital control systems. Our hardware range includes carrier boards that combine DSPs and FPGAs for various PCI/PCIExpress form factors such as slotted/desktop PCI/PCIe, PCI-104/PCIe-104, PMC/XMC, CompactPCI, as well as stand-alone embedded solutions. The DSP-FPGA carrier hardware is complemented by high performance analog and digital I/O modules as well as all necessary accessories like cables and terminal blocks.
