Power Supply Test
-
Product
Power Supply Test System
-
The Procyon PTS 2100-10 is a configurable turnkey Power Test System, delivering automated test equipment (ATE) to some of the world’s largest-volume manufacturers as well as the affordability needed by niche market producers. Aerospace, defense, and avionics power supply ATE test systems applications include functional testing of AC and DC power supplies, generator, and engine control units, as well as a wide range of associated electronics.
-
Product
230V / 36 Amp Load
EL08-230M
-
For High Voltage UPS Battery Testing and Power Supply testing. This particular Load has been designed to operate with UPS Battery Systems and Telecom Rectifiers and Power Supplies with output Voltages in the range of 153V to 230V and is extremely cost effective.
-
Product
Transformer Heat Run Tester
-
1. Suitable for all transformers below 240MVA heat run test and winding resistance testing.2. Printing heat run data automatically.3. With double power supply, can test high voltage side and low voltage side simultaneously and test any operation respectively.4. With anti breakage protection function of inductive test items.
-
Product
PXI-2586, 10-Channel, 12 A, SPST PXI Relay Module
778572-86
Relay
10-Channel, 12 A, SPST PXI Relay Module—The PXI‑2586 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay has low contact resistance and high isolation voltage. The PXI‑2586 is fully software programmable. It is rated for both high currents and high voltages, so it is ideal for switching power signals and loads in control applications and battery, power supply, and automotive testing.
-
Product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781421-14
Matrix Switch Module
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781421-11
Reed Relay
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Power Products
-
With the advancing development and expansion of renewable energies, modern electrical equipment must be developed, manufactured and tested according to nationally as well as internationally valid standards. This requires powerful power supplies & test equipment.Thanks to our extensive product portfolio with the full range of devices, we are able to cover all relevant areas of application. Our range includes standardised desktop units for single workstations up to individually and customised modified special solutions in 19” racks in the megawatt range with voltages up to 2.25 kV.
-
Product
4kW Electronic Load
PT04-48
-
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 48V and 24V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
Product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-33
Relay Matrix Module
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
SWB-2834, 8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-34
Relay Matrix Module
8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2834 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Power Supply Testers
-
Qmax Test Technologies Pvt. Ltd.
Power Supply Tester is an integrated package of hardware such as AC/DC Power Sources, DC Loads, Noise Measurement Unit, and DMM etc configured as per user applications, which makes it suitable for testing wide range of Power Supplies and provide economic solution for testing AC/ DC and DC/DC power supplies and converters. The Power Supply Boards that passed in the first level of screening for Go-No Go tests will undergo a second level testing. The second level of testing measures all the key parameters of the power supply such as line regulation, load regulation, efficiency etc and check whether the results are within the mentioned limit, if not declare the UUT (Power Supply Board Under Test) as a failed one.
-
Product
SWB-2815, 4x86, 0.3 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-15
Reed Relay
4x86, 0.3 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2815 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
110V / 100 Amp Load
BD12-110P-48/24
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 110V battery systems and is extremely costeffective.
-
Product
Electronic Load Device
786532-01
-
The RMX-4006 provides capabilities for qualifying power designs and validating power supply functionality in a production environment. You can combine Electronic Load Devices to customize your test system based on the number of channels, maximum load power, and voltage and current of each channel. You can connect multiple RMX-4006 devices in parallel to provide higher power capabilities for your power supply tests. This feature gives flexibility for future projects that have different power requirements.
-
Product
Single Channel Microphone Power Supply
SoundConnect Microphone Power Supply
-
SoundConnect is a cost-effective, single-channel microphone power supply for audio test applications.
-
Product
8-CH 14-bit 100 MS/s High-Speed PXI Express Digitizer
PXIe-9848
Digitizer
The ADLINK PXIe-9848/9848H is an 8-channel, 14-bit, 100 MS/s digitizer delivering both high-accuracy measurement results and high-dynamic performance. With a PXI Express bus interface and ample onboard acquisition memory up to 512 MB, the PXIe-9848/9848H can easily manage simultaneous 8-CH data streaming. High density and high speed digitizer features ideally position the PXIe-9848/9848H for applications such as LIDAR, radar signal acquisition, and PSU (Power Supply Unit) testing applications.The PXIe-9848 provides a flexible set of input ranges from ±0.2V to ±2V, software selectable 50Ω or 1MΩ input impedance, a wide variety of triggering options and tight synchronization capability, all maximizing convenience of use. In addition, ADLINK provides the PXIe-9848H, features a x15/x50 signal condition module providing both high input voltage range of ±100V and high dynamic performance, delivering the optimum solution to measurement range expansion in a PXI system.
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781420-17
Relay Matrix Module
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
ATE Test Systems
-
Introducing the Procyon ATE System! When it comes to ATE Test Systems for a for low- to high-volume production, Intepro has the testing power you require to be successful. For more than three decades, Intepro Systems has designed, built and integrated power supply test equipment for the world’s largest and smallest power supply manufacturers.
-
Product
Boiler Tube Oxide Scale Nondestructive Tester
DX-201'
-
This instrument is suitable for measuring non-magnetic stainless steel pipe inner layer accumulation rust. It can use a rechargeable battery, without power supply when test, which is suitable for outdoor environment operation. It can be used 4 hours once charge saturation. This product has been used by Hunan Xiangtan Power Generation Company Limited, Wuhan University, Nanyang Henan Yahekou Power Generation Co., Ltd., Anhui Huainan Pingwei power plants and Changsha thermal power plant, received good evaluations.
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781421-17
Relay Matrix Module
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
SWB-2816, 8x46, 0.3 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-16
Reed Relay
8x46, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2816 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, … individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Switching Power Supply ATS (SMPS ATS)
8200
Power Supply
Chroma Power Supply Auto Test System model 8200 provides complete solution for PC ATX power supply, adapter and battery charger testing. The application oriented system structure makes it the most cost effective test equipment for initial test in power supply production line. To meet the power supply test requirements, Chroma Power Supply Auto Test System model 8200 has built in 20 ready-made test items. Users can simply enter the test conditions and test the power supply features while proceeding. With the report and management functions, Chroma Power Supply Auto Test System model 8200 is able to provide versatile tools to establish test documents and perform system administration.
-
Product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
Test Fixture
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
Product
Grid-Connection Testing System
-
This system is a power supply test system that performs grid-connection testing of distributed power sources (solar cells, fuel cells, gasoline engines, etc.)Enable inverter device testing that complies with the Agency for Natural Resources and Energy’s “Guidelines for System Interconnect Technical Requirements” and the Japan electrical Safety & Environment Technology Laboratories (JET) publication “Testing Methods for Small Solar Cell Power Generation System and System Interconnection Safety Devices”.
-
Product
Load Modules
-
Load Modules are available with a selection of voltage and current ranges. Use for discharge testing batteries, power supplies or test gear.
-
Product
48V / 250 Amp Load
BD15-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and is extremely cost effective.
-
Product
SWB-2810, 4x43, 1 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-10
Reed Relay
4x43, 1 A, No Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
SWB-2810, 4x43, 1 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-10
Reed Relay
4x43, 1 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
AC / DC Electronic Loads – Benchtop Testing to Automated Test Systems
-
Chroma Systems Solutions, Inc.
Chroma is the global leader in Electronic Load manufacturing. Chroma’s AC Electronic Loads are designed for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources, and other power devices such as switches, circuit breakers, fuses and connectors. Chroma’s DC Electronic Loads are used for power testing in all markets including automatic test systems, LED, power supply testing, battery testing, and fuel cell testing. Chroma loads can do it all including full current down to 0.4VDC, CZ mode, user defined waveforms, timing measurements, and 3 current ranges per load. Chroma’s electronic loads come standard with either USB or RS232 ports for control and can be configured for GPIB (IEEE-488) control as well.
-
Product
Electronic Loads
-
Chroma Systems Solutions, Inc.
Power conversion testing for automated test systems, LED drivers, power supply testing, battery testing, and much more.
