Thermal Chamber
See Also: Temperature Forcing Systems, Thermal Shock Chambers
-
Product
Thermal Shock Chamber
-
The Thermal Shock Chamber is specially designedwith independant temperature zones to facilitatethe automatic transfer of product under testthereby simulating a temperature shock to test the reliability of the product as per military and other international standards.
-
Product
Low Outgassing Cables Suitable For Thermal Vacuum Chamber Exposure
-
Low Outgassing Cables Suitable for Thermal Vacuum Chamber Exposure.
-
Product
Thermal Shock Chamber
ETS-Series
-
air-to-air and liquid-to-liquid Thermal Shock Chambers from Envisys are available in different volumes to suit the varied testing needs. Horizontal or vertical models consisting of cold and hot zones with product carrier basket of sizes 50, 100, 150, 300, 600 and 900 litres which transfers the specimen under test between cold and hot zones using electro pneumatic / motorized basket movement.
-
Product
TSE-12-A Thermal Shock Chamber
-
Did you think that getting a thermal shock chamber was too expensive, required special utilities, and half your lab-space? The TSE-12 thermal shock chamber is the solution. Only 26 inches wide, the TSE-12 transfers product loads between cold and hot zones with a temperature range of -65°C to 200°C.
-
Product
Thermal Vacuum Chamber & Control
-
Based on several successful deliveries of complex DAQ systems, WinSoft was selected by 2 major satellite manufacturers to design and build a DAQ and Control systems which are connected to various thermal vacuum chambers - all connected to a central database.The chambers are used for environmental testing. The data collected by the DAQ system is recorded continuously every few seconds over a period of a few months.
-
Product
Compact Temperature Chamber
FB1.5V-UHC Series
-
Based on the proven Bemco FB1.5V Compact Temperature Chamber, the FB1.5V-UHC offers spectacular temperature change rates in excess of 75 C per minute. With an extremely compact footprint these chambers cost about 1/3 of the amount of a typical 2-zone thermal shock chamber such as a Bemco FS2V.
-
Product
Vertical Thermal Shock Chambers
FSV Series
-
Bemco FSV Series Vertical Thermal Shock chambers are available in two zone (FS2V - hot and cold) and three zone (FS3V hot - cold - hot) versions, with two temperature ranges (-75 C to +200 C or -160 C to +200 C), and two types of cooling systems (all mechanical cooling - no expendable refrigerant required, or all LN2). Very low temperature, -160 C chambers, are always liquid nitrogen cooled. Two zone chambers are offered in four standard sizes, while three zone chambers are offered in three standard sizes.
-
Product
Thermal Shock Test Chamber (2 Zone)
-
Guangdong Test EQ Equipment co., Ltd.
- Thermal Shock Chamber: -70℃~150℃, ≤5min recovery, meets MIL-STD-810. Ideal for PCB/IC reliability testing.- ESS Environmental Chamber: Humidity 20%~98% RH, supports GB/T 2423 standards. 40% energy saving vs. competitors.- Liquid-to-Liquid Shock Tester: LN₂ cooling to -196℃, 15s transition time. For aerospace materials validation.- Thermal Cycling Equipment: 25℃/min ramp rate, 1000L capacity. JESD22-A104 compliant.- Benchtop Thermal Chamber: -65℃~150℃, 65dB low noise. Lab-use with USB data export.
-
Product
Thermal Shock Chamber
ATS Series
-
Thermotron thermal shock chambers meet a variety of testing needs and come in three configurations: vertical, horizontal, and double duty. A product transfer mechanism automatically transfers products under test from hot to cold zones and back when programmed in the controller.
-
Product
Thermal Shock Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Chamber provide the sudden temperature changes between extreme cold and extreme hot from -65℃ to 150℃ (customized available), specially for environmental stress screen test of the industries that rely on thermal testing, such as component, board electronic assemblies, defense, material stress, consumer products etc. The thermal shock test can cause faulting or cracking by the expansion and contraction on the products, indicates the hidden manufacturing defects. Bell’s Thermal Shock Chamber ensure you to launch qualified product to the market.
-
Product
Thermal Shock Chambers
-
Weiss Technik Thermal Shock chambers are designed to give quick transitions between a HOT and COLD temperature zones. Available in vertical, horizontal and liquid models. Thermal stock chambers are used in all industries including Automotive, Electronics, Aerospace, and others to help find product defects in electronic components and product assemblies. Thermal shock is important with MIL -STD 883 test standard.
-
Product
Climate Control Test Chamber
-
ACMAS's Climate Test Chamber is ideally suited for specimen test requiring quick changes of temperature. It covers various applications from JEDEC and IEC test standards. ACMAS Thermal Cyclic Chamber is equipped with advanced technology such as specimen temperature control which allows linear specimen temperature rates of change during rapid thermal cycling or accurate temperature ramp control. This chamber is also known as Climatic Test Chamber and Climate Controlled Test Chamber.
-
Product
Thermal Abuse Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Thermal abuse test chamber is suitable for standard IEC 62133-2017, UL 1642 and GB 31241-2014.
-
Product
Pyroelectric and Thermal Testing
-
The optional Chamber Task measures the Pulse Polarization response and Small Signal Capacitance of a Pyroelectric material that is being heated and/or cooled within a thermal chamber, on a hot chuck or in a furnace. From these measurements the Spontaneous Polarization Pr(q) and the Dielectric Constant er(q) are computed. These are then combined to determine the Electrical Displacement D(q) as a function of the temperature q.
-
Product
Software
BatteryPro
-
Chroma Systems Solutions, Inc.
The software is item driven with built-in tests – meaning no programming is required at all. Users are able to read data from the BMS controller and also includes thermal chamber control. Battery Pro Software supports Chroma’s regenerative battery cyclers and provides a safe and stable testing environment.
-
Product
Chamber/Pyroelectric Task
-
Radiant's Chamber/Pyroelectric Task sets the sample to a series of temperatures by performingGPIB control of an external thermal device. At each temperature it captures the sample’s polarization response and/or small-signalcapacitance. These are combined to calculate the pyroelectric coefficient. The Pyroelectric Task is to be used with a Radiant Test System and a Linkam Stage (-196C to 600C), Thermal Chambers, Hot Chucks, or a Furnace to automatically measure the Pulse Polarization response and Small Signal Capacitance of a Pyroelectric material that is being heated and/or cooled. Radiant's Pyroelectric measurement Task can be added to Vision at additional cost. This measurement suite fully characterizes the pyroelectric charge (polarization) response of the sample under test. The Pyroelectric Task suite controls various thermal controllers such as Quantum Design, Lake Shore, Delta Design, and many others. Detailed Listing of Thermal Controllers Registered in Vision. The Chamber/Pyroelectric Task is quoted upon request.
-
Product
Belt Starter Generator Test Systems
-
D&V has developed 12 V, 48 V and higher voltage BSG and ISG testing systems for performance, endurance and production testing, complete with thermal chambers, chillers and assembly lines.
-
Product
Thermal Shock Testing
-
Quest Engineering has the capability that you've been seeking to perform thermal shock on a wide array of units. Using our specially designed Thermal Shock Chamber which works like a turnstile to shuttle units between extreme hot and extreme cold conditions.
-
Product
TSA Thermal Shock Chambers
-
Traditional three-zone thermal shock chambers can be quite large, as three separate chambers are used. The TSA series has just one chamber, substantially reducing its size. Instead, it circulates cold, hot, or ambient air as needed. The conditioned air is pre-cooled or pre-heated beyond the setpoint, allowing quicker recovery of the desired condition after transfer.
-
Product
Thermal Shock Test Chamber (Three Zone)
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Test Chamber (3 Zone) consist of the Test Zone, Heat Storage Zone and Cold Storage Zone. The specimen stay in test zone, hot and cold air will be blew from the storage zones to achieve rapid temperature change for thermal shock.
-
Product
Thermal Shock Chamber
-
Allows for the rapid transfer of products between temperature extremes, or the alternating heating and cooling of test articles in cyclical manner.
-
Product
Thermal Shock Chamber
-
Wewon Environmental Chambers Co, Ltd.
Makes it possible to quickly and autonomously transfer test items back and forth repeatedly between a hot and cold environment.
-
Product
Temperature/Humidity Vibration Test Systems
EHVC SERIES
-
The EHVC Series is designed for highly accelerated life testing, the demand of which from customers is increasing today. This is a joint system of the AGREE chamber and thermal shock chamber that we have manufactured and makes the temperature rate up to 20℃/min feasible with a compressor only. With this feature, the highly accelerated life test such as AGREE tests, most thermal shock tests can be performed with one unit.
-
-
Product
Benchtop Temperature Chamber | Environmental Test Chamber
-
The first true Hybrid Temperature Chamber/Platform combination called the Hybrid Benchtop Chamber. The floor of the chamber is a completely functioning Hot/Cold Plate, independent or simultaneous with the chamber. Our models come in different sizes: Micro, Small, and Medium thermal Chambers.
-
Product
Thermal Shock Chambers
-
We provide a large selection of thermal shock chambers to accommodate various types of product testing. Thermal Shock Chambers perform tailored environmental stress screening of component and board electronic assemblies. Our unique chamber design transfers product between two extreme temperature-controlled chambers, passing equal volumes of high velocity conditioned air over the product and resulting in rapid product temperature changes. The induced thermal stresses can reveal hidden manufacturing defects in electronic sub-assemblies and other components by the expansion and contraction of critical parts.
-
Product
Thermal Shock Test Chambers
-
How well does your product stand up to the shock of extreme thermal temperature changes? Tenney Environmental's thermal shock test chambers take products from 200°C to -65°C in just seconds.
-
Product
Thermal Vacuum Chamber
-
Telstar Vacuum Solutions offers innovative custom solutions in design, construction and installation of space simulation thermal vacuum chambers, specially developed to optimize testing efficiency.
-
Product
Test House Services
-
At TS-Space Systems we have over 30 years experience in designing, building and operating vacuum systems for space simulation and materials testing. We have three in-house thermal vacuum chambers which are configurable for a range of temperatures for either monitored vacuum bakeout or thermal vacuum cycling. We design, build and operate these systems in-house which means we are more flexible than most test houses and are happy to modify feedthroughs, manufacture additional support equipment and even change the operation of the chambers, where possible, in order to accomodate customer requirements.
-
Product
Thermal Shock Chambers
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Thermal Shock Chambers are designed for the safe, efficient, and accurate environmental testing of electronics and consumer products, and aerospace, telecommunications, and military and defense components.
