UV Sensors
-
Product
Dielectric/Conductivity Sensor
Mini-VariconTM
-
The Mini-Varicon sensor is a thin, flexible dielectric sensor designed for cost-sensitive use with presses, molds, bulk materials or laminates. Patterned on a polyimide substrate, the electrode array is designed to allow a choice of high or low sensitivity, selected by either using the whole sensor or cutting off a portion of the array at a designated line. The Mini-Varicon sensor can be supplied without leads, or with custom-length Teflon-insulated leads attached.
-
Product
UV Measurement
-
The UV measuring system with the tesa UV Strip and the UV Scan from Hönle is suitable for the reliable testing of the UV dose on the object.
-
Product
Hall Effect Sensor
907 XP (Explosion Proof)
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Class I, Div I (D) Class II, Div I (E, F, G) Class III • XLB-3 enclosure • Bi-directional option (907B XP)
-
Product
OEM Speed Sensors
-
Stalker Radar has distilled its speed measurement and detection expertise into its Intelligent Technologies suite of Speed Measurement, Transportation and Traffic, Sports, and Surface Velocity sensors. Stalker Radar precision is now available to engineers worldwide to address virtually any speed measurement application..
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
Product
Custom Sensors Products
-
Stellar Technology offers a comprehensive selection of pressure sensors, including pressure transducers and transmitters, that can be used in a variety of industrial applications.
-
Product
Peak and Average Power Sensors
E9320 Series
-
- Operates with the EPM-P series and P-Series power meters- 300 kHz, 1.5 MHz and 5 MHz video (modulation) bandwidths- Provides peak and average power measurements- Calibration factors stored in EEPROM- Fast measurement speed over the GPIB (up to 1,000 readings per second)- Two frequency ranges: 50 MHz to 6 GHz, and 50 MHz to 18 GHz- Wide dynamic range sensors
-
Product
Water Detection Sensor
EZ-10
-
Panasonic Industrial Devices Sales Company of America
The EX-10 is a special Thru-Beam Sensor that was designed for two purposes; to check fluid levels and to detect the level of liquids containing water. The emitter on the EX-10 Sensor uses a particularly strong IR beam to not only penetrate transparent, but also semitransparent or colored containers such as PFA packages or shampoo bottles. Also, the sensitivity of the Sensor is adjustable to allow it to focus on a target, such as distinguishing foam from liquid in drinks, as an example.
-
Product
Sensor for Filament Inspection
EyeFI
-
EVT presents the EyeFI - the sensor for the inspection of filaments. The sensor contains two cameras with an Aptina sensor and S-Mount lenses. The cameras are perpendicular to each other. It is therefore possible to inspect two sides of the filament, which means that the EyeFI can detect if the filament is out-of-roundness. Additionally the errors and defects can be detected. For example the occurring flaws are point-shaped or partly flaked, or point-shaped and transverse, or also looking like a longitudial rib, or only spots in different shapes. The defects can be detected with the EyeFI sensor. The EyeFI contains board cameras with sensors from Aptina, the IoCap and an evaluation processor. The housing is about 14x10x4 cm in size. The IoCap is the image-capture-IO-board, which is designed and developped by EVT.
-
Product
Conductivity Logger Sensor
NUL-215
-
This logger sensor is based on a probe with two electrodes with known surface area and distance between them. A signal is supplied to the electrodes and by testing the signal behavior, the conductivity of the solution is calculated
-
Product
Stack Probing Sensor
L722
-
The Model L722 Stack Probing Sensor coupled with the L612 Digital Recording Moisture Meter makes it easy to reach deep into stickered units of lumber and take accurate moisture readings without the danger of broken pins. Wagner''s electromagnetic wave technology makes it possible to take multiple readings throughout an entire stack in just minutes.
-
Product
Conductivity Sensors
-
Conductivity sensors measure the specific conductance of liquid processes. The specific conductance is directly related to the presence of ionic species and their concentration. Barben Analytical offers a full range of two electrode and four electrode contacting conductivity sensors for a variety of industrial measurement applications.
-
Product
Pressure Sensors
-
Universal pressure measurement for liquids and gasesSICK offers a portfolio of electronic pressure measurement transmitters and switches that can be adapted to individual customer requirements because of intelligent and varied configuration options. Typically, all SICK devices feature the use of high-quality materials, rugged properties, and precise measurement technology, in addition to being easy to operate and install.
-
Product
LVDT Sensor Amplifiers
-
Analog Devices signal conditioning ICs, together with linear variable differential transformers (LVDTs), can be used to convert mechanical position to a dc voltage. The IC provides both the excitation for the LVDT and the output conversion to dc level with a user selectable gain. ADI LVDT signal conditioners are available to interface with a wide range of LVDTs, including half bridge and standard 4- and 5-wire.
-
Product
Large-Format/Wide-Area Surveillance Sensors
-
L3 Cincinnati Electronics is the industry leader in large-format MWIR with a decade of experience in providing IR technology for major programs such as the F/A-18 and F-35. In addition to our compact 1280 x 1024 and 2048 x 2048 pixel MWIR HD cameras, we are the only manufacturer with IR sensors of 16Mp (4096 x 4096 pixels) currently in use by U.S. assets in overseas combat zones.
-
-
Product
Barometric Pressure Sensors
-
Barometric pressure sensors measure fluctuations in the pressure exerted by the atmosphere. The sensors require protection from condensing humidity, precipitation, and water ingress. They are typically housed with the datalogger inside an environmental enclosure. If the enclosure is airtight, the sensor's pressure port must be vented to the atmosphere.
-
Product
Vision Sensors
-
Providing you the best range of Vision Sensor with effective & timely delivery.
-
Product
Motorsports Sensors
-
Variohm have many years of experience of providing sensors and transducers to the Motorsport Industry in all series. Take a look at our range of Motorsport Sensors below.
-
Product
Turbidity Sensor
TF56-N
-
The TF56-N sensor is an inline real-time device designed to measure light absorbance at 11° caused by interaction with process turbidity. As an NIR light beam is passed through a dynamic process stream, the sensor simultaneously measures the amount of light scattered at 11° and the remaining amount of un-scattered light at 0°.
-
Product
Outdoor Temperature Sensor
ENVIROMUX-STS-O
-
Applications from -40 to 185°F (-40 to 85°C). Accurate to within ±0.9°F (±0.5°C). Weatherproof enclosure. High resistance to external influences on the cable due to digital output signal. Re-calibration is not necessary after initial set-up. Quick release waterproof RJ45 connector. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,942,123 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
Product
High Intensity Acoustic Sensors
-
Columbia Research Laboratories
Columbia's High Intensity Acoustic Sensors are designed for the measurement of gas-borne sound in industrial applications. They are constructed of type 316 SS for use in corrosive environments. These sensors offer a variety of connector and mounting options, all of them when combined with the all-welded construction provide a true hermetic seal.
-
Product
Custom Solutions for UV Intensity Meters & Radiometers
-
OAI offers custom designed solutions built to your unique specification.
-
Product
True RMS Power Sensors
-
LadyBug True RMS Average Power Sensors deliver reliable, accurate power measurements for CW, Pulse, and modulated signals. These diode based sensors feature a wide dynamic range and a great VSWR. The optional external triggering input feature can be used without any external components. Recorder and Trigger outputs are also available. Our patented NoZero NoCal technology make these sensors ideal for calibration systems, automated test stations and other embedded applications.
-
Product
Tyre Pressure and Infra-Red Sensors
-
The system consists of a powered pressure and temperature sensor with transmitter fitted to a wheel rim. This sends pressure and temperature data over an RF link to a compact receiver on the car. Sampling rates increase automatically when either a change in pressure is detected or when wheel inertia is detected. The system stops transmitting below a threshold pressure to preserve battery life. The receiver sends data to the car control via CAN.
-
Product
High Sensitivity Pressure Sensors
-
High sensitivity ICP® pressure sensors are for low pressure measurements requiring excellent resolution and small size. They are used to measure small dynamic hydraulic and pneumatic pressures such as turbulence, noise, sound, and pulsations, especially in adverse environments. They are capable of measuring high-intensity sound pressures from 111 to 210 dB at any static pressure level from full vacuum to 1,000 psi (6,895 kPa).
-
Product
Quartz Impact Force Sensors
-
Impact-style sensors are specifically designed for impact force measurements. The sensor is typically mounted in a free-standing manner with the installed impact cap directed toward the oncoming object with which it will collide.
-
Product
Lambda Oxygen Sensor
KS60002
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
Measurement Sensors
-
High accuracy and measurement stability, at an affordable price. The laser sensor offers best in class performance for accuracy and speed for all linear displacement applications. Utilising an advanced image sensor, high measurement stability is achieved, even on the most challenging of surfaces.
-
Product
UV Lamp Weathering Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood is a company with professional research and development, sales of Bench-top UV test chamber,Bench-top UV lamp aging test chamber,Bench-top UV weathering test chamber,Bench-top UV aging test chamber,Bench-top UV aging test chamber for 23 years. Ultraviolet light in the sun is a major contributor to the durability of most materials. We use UV lamps to simulate the short-wave ultraviolet portion of sunlight, which produces very little visible or infrared spectral energy. We can choose UV lamps of different wavelengths according to different test requirements, because each lamp has different energy and wavelength in total UV irradiation. Generally, UV lamps can be classified into two types: UVA and UVB.
