Brinell Hardness Testers
test the indentation hardness of materials.
See Also: Hardness Testers, Leeb Hardness Testers, Rockwell Hardness Testers, Vickers Hardness Testers
-
Product
Automatic Relay Tester
-
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuits correctly. It is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay testers.
-
Product
Motor Stator Tester
DZ900
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical properties test of stators of y-type three-phase motors.
-
Product
Oil Acidity Tester
-
Weshine Electric Manufacturing Co., Ltd
Automatically complete the operations of extractant addition, neutralization titration and end point discrimination, acid value calculation, data storage and print output.
-
Product
Signature Surge Testers
TS Model
-
Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TS" Model has the same characteristics as the Signature Model (rack-mounted, Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope) but includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
Leakage Current Tester
-
Aarohi Embedded Systems Pvt. Ltd
“ AAROHI” make Leakage current tester is very compact & specially designed microprocessor based instrument to measure mA of motor,Stator.
-
Product
Cable Testers
CableJoG 256
-
The CableJoG 256 can test up to 256 individual connections of all manufacturers of connectors. This simple test instrument stores up to 12 separate connection configurations. Each cable that is tested is compared with the configuration stored in its memory to produce a pass/fail indication of each pin connection
-
Product
Prodution Testers
Effitest E50
-
Effitest e50 is a flexible and cost efficient solution with easy programming, debugging of test programs and life-cycle support.
-
Product
Audio Cable Testers
AudioJog Pro 5
-
ALL new Audio cable tester with SINGLE & DOUBLE ended testing. There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
Product
Battery Tester
BAT-250-EUR
-
Is designed for one-handed,comfortable and reliable battery measurements. The uniquely designed tester offers an ergonomic slider and a v-shaped side cradle to better hold batteries in place during testing and a contoured case shape that fits neatly in your hand. Testing your batteries has never been easier.
-
Product
Website Tester
-
Find out how well your site works across mobile and desktop devices. Test how mobile-friendly your site is. Test your site for mobile friendliness, mobile speed, and desktop speed.
-
Product
Qualification Tester
LQ402
-
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 6 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 2 cabinets. One is for the electronic components with the primary measurement devices and the other one holds the 6 load boxes.
-
Product
Leakage Current Testers
-
For general-use electrical devices Built-in non-medical use networks For rated currents of up to 20A For automatic testing on production lines, etc.
-
Product
Electronic Toy Tester
-
Programmable ultra high resistance tester is used to test the high resistance of different kinds of material.
-
Product
Withstanding Voltage/Insulation Tester
-
AllWin Instrument Science and Technology Co., Ltd.
W to I, I to W automatic conversionVFD display
-
Product
Peel Force Tester
PT-55
-
V-TEK Peel Force Testers are built to test, confirm, and record proper sealing strength of cover tape to carrier tape. This ensures parts are secure and protected, yet will release at the designated force. The PT-55 Peel Force Tester incorporates new technology and performance features to make set up easy, maintenance minimal, and calibration accurate. The lightweight design can accommodate 8-120mm tape widths and operates at peel speeds of 120mm/min or 300mm/min.
-
-
Product
Hydrogen Leak Tester
T8999
-
T8999 is a tool designed to meet the increasing need for easy and clean identification of the position of the leak on a piece being tested, therefore eliminating the need for methods such as water tank immersion or use of leak detecting sprays, which are harmful for the pieces which could develop rust or pieces that are difficult to accurately clean.
-
Product
Service Testers
-
Service tester with receiver probe, laser pyrometer, alligator clip cable, 10 inch handle, manual and standard bag.
-
Product
Vapor Pressure Tester
-
The MINIVAP laboratory and process vapor pressure analyzers are the worldwide accepted standard instruments for the determination of the vapor pressure of gasoline, crude oil and LPG.
-
Product
High-acceleration Shock Tester
DP-1200-18
-
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
-
Product
Insulating Oil Testers
-
The main functions of electrical insulating oils are heat dissipation and reliable insulation of energised parts of electrical installations. During the normal operation, moisture and other impurities penetrate into insulating oils, leading to a deterioration of their dielectric properties. This in turn may result in catastrophic failures of critical electrical equipment.
-
Product
Waterproof pH Tester
pHTestr 10
-
Large Display Screen - dual display LCD for enhanced readability, provides comprehensive meter information
-
Product
Force Testers
-
Imada has many pre-configured test systems for dedicated testing of a particular force testing application. Cant find your application? Contact us and speak with one of our engineers.
-
Product
Breaking Force Tester
ZDY-02
-
ZDY-02 Breaking Force Tester is applied for break force test of the ampoule, lipstick, lip cream and other materials.
-
Product
Transformer Bench Tester
KVBT
-
KV Hipot Power Test Equipment Co.,Ltd
Transformer Test System is applied for ex-work and maintenance detecting on various transformers.
-
Product
Cable Testers
LINKMASTER
-
The LinkMaster Tester consists of two units. The main unit is connected to one end of the cable to be tested and the remote unit is connected to the jack at the far end of the cable (wall outlet, patch panel port, etc.)
-
Product
Wafer Tester
-
Tokyo Electronics Trading Co., Ltd.
A vital step in the Semiconductor Value Stream, focusing on electrical screening and consumption of Known Good Die (KGD).
-
Product
Combination Board Tester
-
Qmax Test Technologies Pvt. Ltd.
Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
Product
Hydraulic Adhesion Testers
108
-
The Elcometer 108 Hydraulic Adhesion Tester is an extremely versatile Type III* adhesion gauge which can be used for many adhesion requirements.
