Exposure
-
Product
Light and Energy Meter
Model 659
-
UV Light and Energy Meter for use with all wafer steppers. For over 45 years, OAI is a world leader in UV Light and Energy Measurement Instrumentation used for reliable accurate calibrated control of the photolithography processes in the Semiconductor, MEMS, Wafer Packaging and Wafer Bumping Industries. The New Model 659 is an advanced UV exposure analyzer specifically designed for use with all wafer steppers including high intensity wafer steppers. This meter averages up to 400 exposure readings, has Ethernet and USB interface for downloading recorded measurements, and has intensity range of up to 7,500mW/cm2. Probes are available in wavelength of 365nm, 400nm, 420nm & 436nm. OAI has a complete certified calibration lab to maintain the performance, quality and reliability of our meters. The Model 659 meter is traceable to NIST standards.
-
Product
Physical Testing Test
-
Physical Testing by Aero Nav: mechanical, weathering, environmental, immersion, electrical, luminance, thermal analysis, thermal conductivity, water exposure, saltwater exposure, etc.
-
Product
Indoor Air Quality Meter CO, CO2, Temp, RH%
AQM4
-
UEi Test & Measurement Instruments
Four measurements in one instrument; carbon monoxide (CO), carbon dioxide (CO2), temperature and relative humidity. Use calculated 8 hour Time Weighted Average (TWA) and 15 minute short term exposure limits of CO2 for compliance testing and CO measurements for safety testing. Record, recall or download all readings to personal computer for later analysis or record keeping.
-
Product
Radiometers
-
UV Intensity Meters & Visible Intensity Meter for Light Curing Systems. Dymax UV and visible radiometers are simple to operate and allow operators to monitor and document a UV/Visible light curing process. A low UV/Visible intensity measurement signals an operator to replace the bulb, reflector, or lightguide. Radiometers can also be used to confirm that operators are properly shielded from UV/Visible exposure. Degradation of curing bulbs, lightguides, and reflectors can decrease intensity, resulting in incomplete cures.
-
Product
Crawler Control Unit
CCU186
-
The CCU186 control unit for crawlers possesses a distinct advantage compared to existing products. In fact, all of the performances that are usually achieved with standard control units are now available in the crawler configuration. Automatic slow preheating, the progressive rise in voltage with each exposure, as well as a selection of set values are all included in the CCU186.As the CCU186 has been entirely fitted with industrial electronic components, it is perfectly suited to the often extreme conditions of automatic intra-tube control campaigns.
-
Product
High Dynamic Range IR Camera
HDR-IR
-
These cameras maximize camera sensitivity automatically for any static or dynamic scenes. They find the best exposure time according to the scene and allow to resolve targets up to 2500C.
-
Product
SUNTEST
XXL+ FD
-
Atlas Material Testing Solutions
The Atlas SUNTEST XXL+FD is an extra-large light stability test chamber especially tailored towards the needs of consumer goods, food and beverage testing. Its 3000 cm2 flatbed exposure area and tall chamber height is best-in-class for 3-D specimens testing and can accommodate all types of bottles and packaging.
-
Product
Low Outgassing Cables Suitable For Thermal Vacuum Chamber Exposure
-
Low Outgassing Cables Suitable for Thermal Vacuum Chamber Exposure.
-
Product
3.4 MP Custom Lens Low Light Camera Module
e-CAM30_CUMI0330_MOD
-
e-CAM30_CUMI0330_MOD is a high performance, small form factor, 3.4 MP pluggable Low Light Camera Module with S-Mount lens holder. It is based on AR0330 - a 3.4MP CMOS Image sensor from ON Semiconductor®. It has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs the entire Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images, videos and the optional MJPEG compressions.
-
Product
EMF Detector
ElectroSensor™
-
This EMF detector is an unparalleled value that offers fast, reliable, and user-friendly measurements of electromagnetic pollution. Since man-made alternating current (AC) is different from naturally occurring EMF, some sources say that even extended exposure of as low as 2 milliGauss may be harmful. Fortunately, once EMF sources are identified with your ElectroSensor you can moderate your distance and exposure.
-
Product
RF Safety One Stop
-
Radio frequency energy pervades every corner of our environment. Silent and invisible, RF energy can pose direct health safety hazards to workers and the public, as well instigating fires, explosions and technical malfunctions. Employers, property owners and generators of RF energy, many naïve to RF, are all held liable for preventing impermissible exposures, injuries and losses by the FCC, OSHA and the courts.
-
Product
Constant Potential Generator Metal Ceramic X-Ray Tube 30 to 300 kV
CP300C
-
The CP300C is the first panoramic x-ray generator of the CPSeries product range. Equipped with a metal-ceramic tube, the CP300C is a light (less than 30kg) and powerful generator (300 kV), able to penetrate up to 52mm of steel in 10 minutes, making it the best power-to-weight ratio in the world.The efficiency of the CP300C is also maximum thanks to its real 100% duty cycle that allows longer exposure time (> one hour).A full range of accessories is available (holding bars, tripod…) and even a 60°x40° lead diaphragm to convert the CP300C into a directional unit.
-
Product
RF Safety Monitoring
MVG EME Guard XS Radar
-
Specifically designed to alert workers operating near radar transmitters of RF exposures, the unique EME Guard XS Radar is an RF pulse measuring device. It continuously scans for short pulsed signals, and via its built-in alarm and visual system, alerts users whenever the acceptable limits have been exceeded. This RF Safety tool is extremely easy to use and creates a safer working environment close to radar antennas and other pulsed RF sources.
-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
Product
Integrated Clamp-On Ultrasonic Flowmeter
KATflow 210
-
The KATflow 210 is a portable flowmeter designed for situations that require a reliable flow measurement regardless of the conditions in which it needs to be operated. With its advanced battery technology and durable waterproof housing the instrument is intended for long-term installation in remote areas where access to power is limited and exposure to the worst of elements is likely.
-
Product
Human Vibration Management Software
HVManager
-
HVManager is a Risk Assessment and Recordkeeping software tool for reporting Vibration measurements and predicting Personal Exposure Levels. It provides reports of vibration measurement data from hand-arm and whole-body measurements acquired from the Larson Davis HVM100 Human Vibration Meter and produces vibration database records by tool type and serial number. HVManager also compiles cumulative predicted vibration exposure levels from any combination of tools and task durations taken from the measurement database.
-
Product
Light and Energy Meter
Model 656
-
OAI Model 656 Meter is designed for use with all mask aligners and flood exposure systems. For over 45 years, OAI is a world leader in UV Light & Energy Measurement Instrumentation used for reliable accurate calibrated control of the photolithography processes in the Semiconductor, MEMS, Wafer Packaging and Wafer Bumping Industries.
-
Product
Line Scan Camera
Piranha4
-
The Piranha4 cameras offer advanced features such as sub-pixel spatial correction, areas of interest (up to 4 at a time) to reduce data processing and simplify cabling, as well as dual-line area mode to double line rate, HDR mode, shading and lens correction. The Piranha4 is built for the real world with features to ease system integration. The advanced GenICam compliant user interface makes it easy to set up and control camera parameters such as exposure control, FFC, white balance, gain, test patterns, diagnostics and more.
-
Product
Solar Spectrum Test Chamber / Solar Radiation Test Chamber
-
WEIBER Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. Weiber provide Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Weiber provide Solar Simulation Test Chamber.
-
Product
High Speed Cameras
MINI SERIES
-
Three performance level models – Mini AX50, AX100 and AX200 – deliver 1-megapixel image resolution (1024 x 1024 pixels) at frame rates up to 2,000fps, 4,000fps and 6,400fps respectively. All three Mini AX models offer a minimum exposure duration of 1μs as standard with recording memory options up to 32GB providing extended recording times and triggering flexibility. (Sub-microsecond option available on MINI AX200, subject to export approval).
-
Product
Sound Level Meters
-
A sound level meter is a measuring instrument used to assess noise or sound levels by measuring sound pressure. Often referred to as a sound pressure level (SPL) meter, decibel (dB) meter, noise meter or noise dosimeter, a sound level meter uses a microphone to capture sound. The sound is then evaluated within the sound level meter and acoustic measurement values are shown on the display of the sound level meter. The most common unit of acoustic measurement for sound is the decibel (dB); however, some sound level meter devices also determine the equivalent continuous sound level (Leq) and other acoustic parameters. With a portable sound level meter, industrial hygiene and workplace safety professionals can measure sound levels in multiple locations to ensure environmental conditions fall within recommended exposure limits (RELs). Some sound level meter devices can be permanently installed for continuous monitoring of sound levels at a work or job site.
-
Product
Horizontal Flammability Tester
UI-TX40
-
Horizontal Flammability Tester – Horizontal Flammability Chamber is used to test textile and material used in vehicles horizontal burning rate when exposure to a small flame. Horizontal Flammability Test Method includes ISO 3795, ASTM D5132, JIS D1201, SAE J369, FZ/T01028, GB/T8410, GB/T20953 and etc.
-
Product
Radiation Meters
-
A radiation meters is a device designed for measuring varying types of radiation. These devices are portable and are used to inspect personnel, equipment, and facilities for radioactive contamination by measuring the emission of certain radiation particles. They are used to measure external or ambient ionizing radiation field to assess the direct exposure hazard.
-
Product
IP67 Testing
-
IP67 is an electronics and sealed device attribute requirement with a physical no-water ingress testing process used to determine whether components meet the requirements needed to receive an IP (ingress protection) rating. Devices with this internationally recognized rating resist exposure to dust and withstand up to 30 minutes of submersion in water up to 40 inches (1 meter) in depth. Products assigned an IP67 rating are typically used in outdoor applications or other environments requiring resistance to dust, moisture, and water submersion.
-
Product
Power Temperature Cycling
-
Typically, this test would be selected when during its normal operating activity, the device is subjected to high temperature excursions and is required to power on and off at all temperatures. The power and temperature cycling test will determine the ability of a device to withstand exposure to such temperature extremes with operating biases periodically applied and removed. The worst case conditions expected in a typical; application will be simulated.
-
Product
Salt Spray Testing
-
Salt Spray testing (Also known as Salt Fog testing) is often used for testing the corrosion resistance of metallic products, or for testing the corrosion resistant coating applied to metallic products, in order to verify that they will function properly when exposed to salt corrosion. This specific type of testing is used as a means to accelerate the salt corrosion exposure in order to gather data on the long or short term effects of salt corrosion on the product or coating material.
-
Product
Light Meters
-
An instrument for measuring the intensity of light, used chiefly to show the correct exposure when taking a photograph.
-
Product
EMF Exposure Test
sXcTEM835
-
Tests radiofrequency electromagnetic field exposures from mobile communication devices operating in the 900 MHz region (additional frequencies upon request). The setup is based on two Crawford TEM cells that are blindly excited by a fully computer-controlled signal unit.
-
Product
Conductive Emission Measurement
-
Holland Shielding Systems B.V.
On site testing for exposure limits in working conditions to any international standard. This involve pacemakers and HSE Heath and safety executive, invitarisations worldwide.
-
Product
Low Light USB Camera With Microphone
Conversa
-
Conversa, camera for conversation (See3CAM_CU38), is a 3.4 MP low light USB 3.1 Gen1 camera with built-in stereo microphone providing 16bit audio @48KHz. This low-light USB camera is the next advanced version of our flagship product See3CAM_CU30, with built-in stereo microphone for crystal clear sound. It is a plug-and-play (UVC and UAC) compliant USB 3.1 Gen1 SuperSpeed camera and is also backward compatible with USB 2.0 host ports. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It has a dedicated, high-performance Image Signal Processor chip (ISP) that performs all the Auto functions (Auto White Balance, Auto Exposure control).
