Speed Sensors
-
Product
Engine Speed Control and Measurement (Test Set A)
MS 1100
-
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
Product
Digital Strain Gauge Sensor
ZET 7111
-
The ZET 7111 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or separate external tension gauges connected using half-bridge or bridge scheme.
-
Product
PCIe 16 Bit High Speed Digitizer - 250 MS/s on 2 Channels
M4I.4420-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Alignment Sensors and Switches
-
The Touchswitch is an electro-mechanical limit switch with no moving parts, which detects tracking and misalignment problems on bucket elevators and conveyors. When a belt misaligns or a pulley moves over and contacts the sensor, the built in solid-state electronic circuitry detects the lateral force of the belt or pulley and activates a voltage free relay contact. This relay contact is used to immediately alarm and shutdown the machine.
-
Product
Optical Sensors
-
Leuze electronic GmbH + Co. KG
Optical sensors use light in various forms to perform their detection tasks. An extensive product line is available with reliable and efficient sensor solutions for all applications that can be solved optically. Object detection for different surfaces, object sizes and colors requires various function principles, such as a throughbeam photoelectric sensor, a retro-reflective photoelectric sensor or a diffuse reflection sensor. All different operating principles are usually available in a given series (size). Universal series are also available with extended models and additional useful functions.
-
Product
Load Cells and Sensors
-
AMETEK Sensors, Test & Calibration
Our high quality load cells and sensors are used for materials testing and force measurement all over the world.The full bridge load cells and sensors provide high precision measurements that ensure adherence to the international standards.
-
Product
CMOS Imaging Sensors
-
CMOS imaging sensors from ams feature global and rolling shutter capability, low noise, high dynamic range and high frame rates.
-
Product
3D Profile Sensor
Z-Trak2
-
Z-Trak™2 is a new family of 3D profile sensors built on Teledyne Imaging’s 3D image sensor technology, ushering in a new era of 5GigE 3D profile sensors for high-speed, in-line 3D applications.
-
Product
Humidity Sensor Components
-
Based on a unique capacitive cell, our temperature and humidity sensors are designed for high volume applications where humidity measurement is needed.
-
Product
Sensor Solutions
-
The combination of extensive test & measurement know-how, a complete understanding of project goals and a thorough overview of industry-specific characteristics lead to productive solutions for our customers.When it comes to providing a holistic solution, we not only offer imc measurement hardware and software, but also innovative sensor solutions for a wide range of application areas.
-
Product
Eddy-Current Sensors
-
Eddy-Current sensors are noncontact devices capable of high-resolution measurement of the position and/or change of position of any conductive target. Eddy-Current sensors are also called inductive sensors, but generally "eddy current" refers to precision displacement instruments (or nondestructive testing probes) and "inductive" refers to inexpensive proximity switches. High resolution and tolerance of dirty environments make eddy-current sensors indispensable in today's modern industrial operations.
-
Product
Reference Temperature Sensors
-
AMETEK Sensors, Test & Calibration
Our reference sensors can be used as your daily working-reference sensors in laboratory or field calibration applications. A large selection of types are available, including; straight, 90 degree angle, 4 mm or 1/4”. The superior design and specifications combined with a long history of reliability and low drift have made the STS probes the working-standard in many EN/IEC 17025 accredited laboratories worldwide. The DLC sensors are a part of our patented Dynamic Load Compensation system.
-
Product
Lightning Sensors
-
Scientific Sales boasts a full line of lightning detectors and lightning warning alarms to protect people from unpredictable and deadly lightning strikes. Lighting monitors can detect electrical activity from up to 40 miles away and track a storm as it approaches with audible and LED alarms. Choose from a permanent lightning detector or hand-held lightning sensors for accurate and reliable lightning detection. Scientific Sales’ lightning monitors and lightning sensors are professionally rated and are used by NASA, major airlines and professional sports teams. Industry related applications of lightning meters include construction and drilling sites, golf courses, outdoor event venues, university facilities and more.
-
Product
Capacitive Proximity Sensors
-
Liquids, granulates, glass, powder, wood and more – capacitive sensors detect almost any object by non-contact means, regardless of color, reflection factor, and surface characteristics.
-
Product
Vehicle Presence and Data Collection Sensor
TrafiCam x-stream
-
TrafiCam x-stream combines a CMOS camera and video detector in one unit. TrafiCam x-stream sensors detect and monitor moving and stationary vehicles at signalized intersections and collect traffic data at intersections or interurban roads. Via detection outputs or via IP protocol, vehicle presence information is transmitted to the traffic controller so that signal timing can be adjusted dynamically. TrafiCam x-stream offers streaming video at full frame rate, to be used for traffic monitoring in a control room.
-
Product
CAN Sensor/ Interface
Current
-
Reach Technologies’ CAN Current Sensors sense and digitize conductor current for collection via CAN. The module is ideal for conveniently adding current data to a distributed CAN network. The CAN Current Sensor is configurable via J1939 or CANopen stacks, and are available in Hall Effect and shunt variants.
-
Product
0-10 Volt Sensor
DT140
-
A general sensor that will measure any device or transmitter that produces a linear analog 0-10V output. The voltage can easily be converted to the correct measured units with the help of the Microlab program.
-
-
Product
ITA, i2 MX, EMI, High Speed
410130116
ITA
This i2 MX ITA includes VTAC rail inserts offering 22 slots for SIM inserts and a maximum of 176 contact positions. Includes front protective cover. Mates with high speed i2 MX receiver p/n 310130113.Cable bundle too large? Choose the i2 XL! XL-Sized backshell, bend radius, & cable exit to better accommodate larger cables such as high-power or high-speed cables.
-
Product
Force Logger Sensor
NUL-211
-
This sensor can measure the mass to weightrelationship and study how different pulleysystems affect the effort needed to lift weights.It can also be used to measure push/pull forcesand impacts. There is a hook at the bottom of the force sensor that can be connected to various pulling loads.
-
Product
3D Sensors
-
*Up to 38500 distance values per measurement for a detailed assessment of the application*Configurable outputs*Visual assessment of distance, level or volume*Predefined function blocks*Time-of-flight measurement principle
-
Product
High-Accuracy Sensors For Complex, Real-World Applications
-
Are you building a system that needs to measure real-world data accurately and reliably to make intelligent, real-time decisions? Our large portfolio of sensors measure data from the analog world and deliver it to the digital world. These sensors feature high-accuracy, low-power performance, real-time protection, robust interfaces and compact packages to satisfy the requirements of industrial, automotive, consumer, data center and communications applications. Their high accuracy makes them an excellent choice for high-precision applications, while their small packages and low power consumption make them ideal for hand-held or battery-powered devices. Explore our different types of sensors to find the most cost-effective and space-saving option to suit your specific design requirements.
-
Product
Industrial radar sensors for various applications
-
OndoSense offers ultra-precise, robust and dependable industrial radar sensors for a variety of applications and industries. If needed, we will work out a customized radar sensor solution for your application together with you in a proof of concept. Our radar technology offers solutions adapted to industries such as the metal & steel industry, transport & logistics, mining, mechanical and plant engineering, farming & agriculture, food & packaging, energy sector, chemicals & pharmaceuticals etc.
-
Product
SparkFun Qwiic MicroPressure Sensor
-
The SparkFun Qwiic MicroPressure Sensor is a miniature breakout equipped with Honeywell's 25psi piezoresistive silicon pressure sensor. This MicroPressure Sensor offers a calibrated and compensated pressure sensing range of 60mbar to 2.5bar, easy to read 24 bit digital I2C output, and can be calibrated and compensated over a specific temperature range for sensor offset, sensitivity, temperature effects, and non-linearity using an on-board Application Specific Integrated Circuit (ASIC). With its ultra-low power consumption and Qwiic ports, you've got yourself a power packed little sensor!
-
-
Product
Threaded Miniature Photoelectric Sensor
EX-30 Ver.2
-
Panasonic Industrial Devices Sales Company of America
With an M4 Thru-Beam Type and an M6 Reflective Type Sensor, the user has a series of Miniature Photoelectric Sensors at their disposal from Panasonic. In addition to being quick and easy to install, the EX-30 Series Sensors' integrated signal amplifier, stable mechanical properties, and robust, zinc housing make them attractive alternatives to Photoelectric Sensors with fiber cables.
-
Product
Strain Gauge Sensor
ZET 7010
-
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
Product
Dynamically Controlled, High Speed Digital I/O PXI Express Card
GX5292e
Digital I/O
The GX5292e is a high performance, cost-effective 3U PXI Express dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5292e also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 100 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
Thermocouple Power Sensors
N8482B
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
High Speed Comparators (<100ns Propagation Delay)
-
Analog Devices high speed comparators feature <100 ns propagation delay and are a versatile and easy to use solution for a range of applications. Owing to our proprietary CB and XFCB fabrication processes, our comparators such as the AD790 possess a fast response time with outstanding input voltage resolution.
