Gigabit Passive Optical Network
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB105
-
The FAB105 features a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB105 is perfect fit for AXIOMTEK's SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB105 is compatible with the AX60501 chassis.
-
Product
1-slot Network Attached File Server
DTS1
-
Curtiss-Wright Defense Solutions
Modern unmanned vehicles, ISR aircraft, and mobile ground vehicles are built around a network-centric architecture. The backbone of such systems is Gigabit Ethernet (GbE), operating at 1.25 gigabits per second. With a network switch (or redundant switches) in the middle of the system, any network-enabled device can communicate with any other similar device. In addition, NAS devices like the DTS1 allow any client to retrieve stored files or save new captured files.
-
Product
Vector Network Analyser
LA19-13-02
-
The LA19-13-02 is a PC-driven Vector Network Analyser suitable for measuring a wide range of devices from 3 MHz to 3 GHz with 100 Hz resolution. Its full s-parameter test set includes bias-Ts for biasing active devices. It is housed in a small lightweight package making it very portable.
-
Product
Fiber Optic Modem
VCH-608
-
The VCH-608 fiber optic modem is designed to receive and transmit via a fiber optic communication line (FOCL) signals of frequency and time standards (TSV) :- pulse signals 1 Hz (1 PPS) with delay compensation,- harmonic electrical signals with a nominal value frequency 100 MHz with phase instability compensation.
-
Product
Optical Power Measurement Products
-
The Keysight optical power measurement module family provides a range of power sensor modules (8163xA/B), external optical heads (8162xB) controlled by the interface modules (81618A or 81619A) and return loss modules (8161xA).
-
Product
Optical Filters
-
Alnair Laboratories Corporation
The filter exhibits an ultra-sharp roll-off of 1500dB/nm(12dB/GHz), without compromising the flexibility ofbandwidth- and wavelength-tuning. Ideal for DWDMchannel selection and removing ASE noise.
-
Product
PNA-X Microwave Network Analyzer
N5245B
Network Analyzer
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Network & Data Solutions
-
IDM Technology is the core technology solution set that provides users in severe environments with a means of routing and processing data over internet protocol (IP) based or point-to-point networks using existing, and primarily voice-grade radios.
-
Product
Optical Fiber Identifier
-
OrienTek Optical Technology Ltd.
Optocal Fiber Identifier Economical Solution for Integrated Fiber Preparation Tool Demand● 4 easy-change chucks for:bare fiber, patch cords & ribbon fiber● Identifies 3 common test tones● Identifies dominant traffic direction, audible alarm● Approximate core power reading● Low false detection & insertion loss● Very easy to operate● Battery low indication
-
Product
8 Ports 10GbE SFP+ Network Mezzanine Card
NMC-1011
Network Mezzanine Card
Ideal for high-throughput data center applications and fiber-based networking. 2 x Intel® XL710-BM1, 8 x SFP+ slots, 1 x PCIe 3.0 x8, Gen3, RoHS compliant.
-
Product
Matching Network Solution
Navio
-
Experience simplicity and high reliability in a single, affordable package. The Navio™ matching network leverages our power expertise to precisely match complex plasma impedance to your tuning range. It’s quick, accurate, and repeatable. Available in multiple power ranges and frequencies, choose from a standard offering or a configurable design. Installation is virtually plug-and-play with Advanced Energy’s RF power supplies. Virtual Front Panel software is available for monitoring.
-
Product
Optical Fiber Test Platform
Fiber Lab 3200
-
Fiber Lab 3200 from M2 Optics Inc. is a must-have solution for anyone developing or testing fiber optic products and systems. Available in two types of rack-mount chassis with up to 300km per unit, it offers the most professional approach for using fiber in the laboratory or network. In addition, it provides maximum protection against potential fiber and connector damage.
-
Product
Automated Optical Inspection (AOI)
TR7700 SIII 3D
-
TRI’s ground breaking 3D AOI solution delivers the fastest hybrid PCB inspection combining optical and blue-laser-based true 3D profile measurement for the highest automated defect symptom coverage possible. Integrated state-of-the-art software solution and third generation intelligent hardware platform offer stable and robust 3D solder and component defect inspection and with high inspection coverage and easy programming.
-
Product
Optical Components
-
Spectrolight provides a growing range of Optical Components including connectorized fibers and fiber bundle light guides.
-
Product
Gigabit Ethernet Tester
GET-100
-
GET-100 is a handheld 10M/100M/1000M gigabit Ethernet tester, used for the Ethernet installation, operation and maintenance services.The GET - 100 design in a small and portable device which provides packet capture, network monitoring, networkperformance testing, data generation, test leads and error test functions in an organic whole unit. It is widely used in network layer 1/2/3 BER test and RFC - 2544 test. GET-100 help maintenance people to quickly locate fault and analysis network
-
Product
Optical Switches
-
This latest technology platform presents the best value in terms of size, form factor, durability, and cost. The design of our MEMS optical switch centers on DiCon's proprietary dual-axes tilting MEMS mirror and is expandable up to a 1x36 switch configuration. Large fan-out 1xN optical switches and non-blocking fan-out/fan-in NxM matrix optical switches are built by cascading multiple of these 1xN switches. The MEMS 1xN fiber optic switch passes the stringent Telcordia GR-1221 qualification and is vastly deployed in today’s optical communication networks. With a lifetime of over a billion cycles, the durability of this MEMS device makes it a perfect choice for optical network monitoring applications that require frequent switching.
-
Product
Passive and Active Resistor Trimming for Thick and Thin Film
LRT 2000L
-
*Travel: 6" x 6"*Laser : Fiber Laser Ytterbium 1064 nm*Kerf: 30 to 80 micron Adjustable*Pulse width : 80 nano second*Rap Rate: 1 to 1 million Pulse Per Second*Average Power: 20 watts*Target: Electric crosshair on monitor
-
Product
Optical Analyzers
DNIRA™
-
Neolitics’ DNIRA™ is a real-time, in-line process NIRS that delivers the performance and accuracy of a precision laboratory instrument in a compact, robust, in-line design. It’s easy to install and requires virtually no maintenance post-installation, eliminating the time and difficulty required to keep systems calibrated and the difficulty in replicating or scaling applications within a manufacturing environment.
-
-
Product
Digital Electrical Network Analyzer
2726 NA
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Built-in earth tester.● Built-in loop/psc tester. 0.03-2000Ω (software ctrl).● Built-in voltmeter.● Built-in wiring checker.● One push button smart control.● Display L-N and L-E voltages. 50 to 280Vac (sine).● Display line path impedance. 0.01-2000Ω (software ctrl).● Display earth path impedance. 0.01-2000Ω (software ctrl).● Display neutral path impedance. 0.01-2000Ω (software ctrl).● Display psc line to neutral. 6kA@230Vac supply.● Display psc line to earth. 6kA@230Vac supply.● Re-scroll through previous results.● Bat. ok/low battery indicator.● Auto-off function.● Color coded test leads.● Rugged Case.● Ultra low power consumption.
-
Product
MTP MPO Fiber Optics
-
Shanghai Tarluz Telecom Tech Co., LTD
A high performance MPO connector with multiple engineered product enhancements to improve optical and mechanical performance when compared to generic MPO connectors.
-
Product
Yamasaki Optical Fiber Identifier
TF916
-
The Yamasaki TF916 Optical Fiber Identifier is an essential part of any professional fiber optic toolkit. By inserting fiber into the Yamasaki TF916 Optical Fiber Identifier head, the Yamasaki TF916 Optical Fiber Identifier can be used to identify traffic, traffic direction, frequency and optical power within any singlemode optical fiber. The sleek black outer housing is comprised of an anodized aluminum to make it lightweight and tough. Also included with the Yamasaki TF916 Optical Fiber Identifier are four adaptor heads that are specifically designed to suit various optical fiber types with minimal bend loss. The easy to read ultra-bright LED display and audible tone make operation easier and can save you valuable time in the field.
-
Product
Fiber Optic Cable Assemblies
-
Amphenol Fiber Systems International
For applications demanding reliability, traceability and the highest level of quality, a complete plug-and-play cable assembly directly from the manufacturer offers the highest degree of confidence. For these most demanding applications, AFSI specializes in manufacturing custom cable assemblies with quality components and industry-leading workmanship. AFSI is able to assist in designing and producing custom cable assemblies from a set of requirements or building to a customer print. Our highly skilled technicians are trained to a wide variety of industry standard procedures critical to manufacturing harsh environment fiber optic cable assemblies. All AFSI cable assemblies are manufactured by expert technicians in our state-of-the-art, AS9100 certified facility.
-
Product
Fiber Optic Sensors
-
Achieve highly reliable and precise fiber optic sensing. Advanced Energy’s Luxtron® patented FluorOptic® temperature measurement solutions and WaveCaptureTM Fiber Bragg Grating (FBG) sensing solutions feature many options to meet your application needs.
-
-
Product
Portable Network Expert
EtherScope® nXG
-
Multi-technology, all-in-one handheld network analyzer that enables engineers and technicians to get more done faster, from deployment to maintenance and documentation of their ever-changing Wi-Fi, Bluetooth/BLE, and Ethernet access networks.
-
Product
Optical Tool Kit
TC-406
-
Techwin(China) Industry Co., Ltd
Optical Tool Kit makes ideas happen and makes your work easier.
-
Product
Optical Power Meter Series
-
*High performance detector*Stable and reliable*High sensitivity*Multi-wave test*Relative and absolute power display*SMT, lightweight*Power supply by battery
-
Product
Optical Transmitter
ST1550I
-
Hangzhou Softel Optic Co., Ltd.
When ST1550I Optical Transmitter is applied in the multi-channel transmission, the laser’s chirp effect will react with the link dispersion of the fiber. There will be distortion other receiver. If working with the EDFA, there will be serious CSO deterioration. The distortion and deterioration will increase with the longer distance and more channels. 1550nm internal modulation CATV optic transmitter, has the chirp and dispersion compensation inside, and improves the system index greatly. It can be used in the town where the fund is shortage and the distance is less than 10Km as a transition solution.
-
Product
Network Sensor Interface for USB Pressure Transducers
SI314
-
The Validyne model SI314 is a network interface that connects our model P61 USB pressure Transducer to your smart phone or network web browser. The SI314 supports Ethernet and Wi-Fi connections and will display current pressure readings and transducer status on any web browser or via smart phone. The SI314 also displays the transducer temperature, date of calibration, model and serial numbers and these can be viewed wirelessly or by Ethernet connection. The SI314 makes your P61 accessible from anywhere in the world. Data logging of pressure data is configured via a web browser or smart phone and readings may be stored once per minute to once per hour. A thumb drive or memory card collects the data in comma separated file format(csv) for download to your computer. The data may also be accessed via the network. A graph of the data is also generated on request. A Twitter function allows pressure data to be tweeted from the SI314 at user-defined intervals. The transducer zero and span calibration adjustments are password protected and operated via browser buttons. No potentiometer adjustments are required to calibrate the P61 transducer. Contact our Sales Department for a link to the Demo!
