AC Load Banks
source for testing and measurement of current, voltage and frequency.
See Also: Load Banks, DC Load Banks, Inductive Load Banks, Reactive Load Banks, Resistive Load Banks, UPS
-
Product
Bolt Extensometers for Proof Load Testing
Model 3565
-
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Load Cells
-
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
Product
Network Simulation and Load Testing
-
EXFO offers a complete range of high-performance test solutions, covering the entire converged network from RAN to IMS. By mimicking real-world customer behavior in lab environments, our solutions allow mobile operators and equipment manufacturers to verify their wireless networks before deployment.
-
Product
Electric Servo Motor Type High Speed, High Load, Large Displacement Vibration Tester
-
This tester is a high-speed, high-acceleration vibration tester equipped with an electric servomotor actuator.
-
Product
Load Shedding System
-
An advanced smart load preservation solution must dynamically determine the optimal system response to a variety of system changes and disturbances. Utilizing model-driven foundation with embedded predictive analytics, and optimization algorithms, ETAP's adaptive Intelligent Load Shedding (ILS) solution makes Faster than Real-Time decisions.
-
Product
Load Button Load Cells
-
Interface’s load button load cells are designed for customers who require the measurement of compression forces in a very low height space. They are designed to provide the most accuracy in as little space as possible. The smaller ConvexBT or LBMU can fulfill the need for force measurements at a very respectable precision level that is enough for most applications. Diameters range from ⅜ of an inch to just over 3 inches, with heights from ⅛ of an inch to 2 inches. The shaped load button has a spherical radius to help confine misaligned loads to the primary axis of the cell.
-
Product
Rod End Load Cell
-
Futek Advanced Sensor Technology, Inc.
FUTEK’s Rod End Load Cells provide an excellent solution for applications involving Inline Actuators or Hydraulic Jacks with Male/Female Threads. You will find a capacity
-
Product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
-
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
Product
Loaded Spectrophotometer
DSCD-900
-
DSCD-900 is a highly performance spectrophotometer with test caliber upward. The instrument adopts the geometric conditions of D/8 lighting and observation of CIE recommendations, integration of the full band LED composite light source, double beam optical system, ETC every-time calibration technology, spectral reflectance standard deviation within 0.08, maximum of colorimetric values ΔE*ab is 0.03, to provide all the necessary color formula. It could be widely used for coating, printing, textile, meet plastic, food, medicine, automobile field to meet customers’ measurement requirement.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-18S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Ultra compact size with 18mmφ jaw opening capability.*High sensitivity and least affection from external magnetic field.
-
Product
Low Capacity Single Point Bending Beam Load Cells
LSP SERIES
-
The LSP Series is a low capacity, low cost, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The LSP Series features a moisture proof sealant.
-
Product
Three-Phase AC Power Source 320 Vrms, 18 KVA, 5000 Hz
AC6918H
-
Keysight’s AC6900 Series three-phase power sources provide a complete AC and DC power solution by combining the capabilities of a multimeter, harmonic analyzer, and power analyzer in one instrument.
-
Product
High Power Programmable AC Source with Transients
61510
-
Chroma Systems Solutions, Inc.
Power Rating:61511: 12KVA61512: 18KVAVoltage Range: 0-150V/0-300V / AutoConfigurations with input voltage of 220V or 480VFrequency: DC, 15Hz-1500HzSingle-phase or three-phase output selectableProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage and current limitHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientLIST, PULSE, STEP mode functions for testing Power Line Disturbance (PLD) simulationVoltage dips, short interruption and voltage variation simulationHarmonics, inter-harmonics waveform synthesizerComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetCapable of delivering power output up to 90KVA by implementing Master-slave parallel operation
-
Product
Thermocouple, Insert, ITA, SIM, 8 Pos, 3 Slot (not loaded)
510181111
SIM Insert
Thermocouple, Insert, ITA, SIM, 8 Pos, 3 Slot (not loaded)Compatible with 410130116, ITA, i2 MX, 22 Slot VTAC/SIM Insert, EMI, and XL version 410130133Not loaded. Thermocouple patchcords need to be purchased separately.
-
Product
Medium Voltage Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
Optimize your medium voltage power systems with our Container Load Banks. Engineered to perfection, these load banks offer advanced features and robust performance, ensuring accurate testing and maximum reliability. Unleash the power of excellence.
-
Product
Digital 125 Amp Battery Load Tester
6033
-
• Heavy load enables the 6033 to detect bad batteries missed by other electronic testers• Automatically computes the CCA of the battery under load• Kelvin connected digital meter displays the following values:• Current Battery Voltage• Maximum Voltage reading• Minimum Voltage reading• Automatic load cycle• PATENTED• Made in USA of US and Global Components
-
Product
PXI 4 Banks of 20 Channel 1 Pole MUX
40-615-021-4/20/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
True AC RMS Panel Meter
-
The Laureate? True RMS meter offers a high accuracy 4 1/2 digit display for five voltage ranges and four current ranges. It is suited for AC applications where there is considerable distortion of current waveforms from nonlinear loading. The input is AC coupled to read only the AC component, such as ripple on a power supply.
-
Product
AC / DC Current Probe, 2 MHz, 500 Arms
N2780B
Battery Probe
The N2780B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 500 Arms continuous.
-
Product
High Power Programmable AC Source
61610
-
Chroma Systems Solutions, Inc.
Power Rating:61511/61611: 12KVA61512/61612: 18KVAVoltage Range: 0-150V/0-300V / AutoConfigurations with input voltage of 220V or 480VFrequency: DC, 15Hz-1500HzSingle-phase or three-phase output selectableProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage and current limitHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetCapable of delivering power output up to 90KVA by implementing Master-slave parallel operation
-
Product
External Load Module
ELM
-
Circuit breakers are often overlooked during maintenance of electrical systems in aircraft, or often only verified for open and closed states. To test the true functional purpose of a circuit breaker it requires the application of current in excess of the rated trip value and then measure the time for the breaker to actually trip. This is the only way to verify that a circuit breaker will react as designed if an electrical failure occurs.
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-30
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of feeder*Compact size*AC 1mA～100A
-
Product
Split type AC Current Sensor
CTF-400A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of main cable. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
-
Product
Performance AC Power Source, 375 VA, 300 V, 3.25 A
6811C
-
Maximize your investment with five instruments in one device Increase your productivity with extensive built-in power measurement capabilities Flexible IO: LAN/LXI Core, USB and GPIB Lower your cost of ownership with global support & the longest standard warranty in the industry
-
Product
Split type AC Current Transformer
CTF-100T
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Wire stopper is equipped for the slipping protection.*The special connector is not necessary as the output terminals are provided.*Open circuit protection and nonflammable plastic material.
-
Product
3-Phase AC Voltage Transducer
ENVIROMUX-PT3-600
-
Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.
-
Product
AC VOLTAGE MEASUREMENT (AC or AC + DC TrueRMS) Digital Multimeter
1320
-
± 199.9mV, ± 1.999V, ± 19.99V, ± 199.9V, ± 1200V, 5 Ranges, AC VOLTAGE MEASUREMENT (AC or AC + DC TrueRMS)
-
Product
Electronic Loads
-
AMETEK Programmable Power, Inc.
Electronic loads have found a variety of applications ranging from power converter testing to current modulation. A large range of power sources can be tested using an electronic load from converters, inverters and UPSs to electrochemical sources such as batteries and fuel cells.
-
Product
RC-50 Artificial Phantom Load with Power Factor
480
-
The RC-50 Artificial Phantom Load with Power Factor (Catalog No. 480) has been re-designed to meet the most exacting requirements. It operates from a single phase source and will deliver current at either unity or 50% power factor at all full load ranges.
-
Product
Regenerative AC load function
61800 Series Optional Function
-
The regenerative AC load function consists of various modes such as CC Rectified mode, CP Rectified mode, CR mode, CC Phase lead/lag mode and CP Phase lead/ lag mode. The Rectified Mode is capable of simulating non-linear rectified loads with characteristics similar to Chroma 63800 series AC load where the voltage and current operate at the 1st and 3rd quadrant. The Rectified Mode supports both CC and CP functions with current, power and CF as parameter settings.
