DC Load Banks
See Also: Load Banks, AC Load Banks, Inductive Load Banks, Reactive Load Banks, Resistive Load Banks
-
Product
110V / 90 Amp Load
EL12-110M
-
For Telecom Rectifier and Power Supply testing. This particular Load has been designed to operate with Telecom 110V Rectifiers and Power Supplies with output Voltages in the range of 100V to 135V and is extremely cost effective.
-
-
Product
Programmable DC Power
XR Series
-
The XR Series utilizes the latest IGBT devices to drive down size and increase performance. The high frequency design delivers fast transient response and low output ripple. This performance coupled with Magna-Power''s rugged current-fed power processing, enables confidence in even the most demanding applications.
-
Product
48V / 250 Amp Load
BD15-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and is extremely cost effective.
-
Product
DC Bench Power
XPF Series
-
AMETEK Programmable Power, Inc.
The Sorensen XPF is a new type of bench power supply designed to meet the need for flexibility in the choice of voltage and current. Typically, the maximum voltage and maximum current are not required simultaneously. The PowerFlexTM design enables higher currents to be generated at lower voltages within an overall power limit envelope. This is achieved by using the latest switch-mode technology.
-
Product
4kW Electronic Load
PT04-110
-
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 110V and 48V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
-
Product
Axle Load Simulators
-
In case vehicles need to perform a brake test in laden condition, one could consider to use a load simulator. In that case the vehicles can come to the brake test unladen; the load simulator will add the required load to the axles.
-
Product
Load & Fatigue Testing
-
DATASYST Engineering & Testing Services, Inc.
Due to variations in types and levels of load and fatigue exposure, DATASYST works with each client to determine the best possible test plan to capture the information and issues that may be present in application.
-
Product
DC current Sensors
CTH
-
The CTH sensors convert dc current to an isolated voltage output, the CTHR sensors convert ac current to a dc output signal proportional to the Arms. All popular process control voltage and current loop outputs are available. Through hole or split core options mean that connection is non-intrusive and straightforward. The available input range of the CTH sensors is any value from 5A to 6000Adc.
-
Product
Battery Load Tester
BT-100
-
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
Product
Loading Rheostats (Resistive Load)
-
Supreme Instrument Laboratories
Loading Rheostat is a device specially designed to meet the requirements of Engineering Laboratories, Electrical Test Rooms and Industries. It is used for loading transformers, power generators, supply mains etc. neatly and efficiently. It can also be used advantageously for regulating current and adjusting voltage besides its application for calibrating meters and thus eliminating the need for graded rheostats.
-
Product
AC Load Banks
-
Power House Manufacturing, Inc.
Hand carried AC load banks in any capacity to meet your load testing needs. Power House Manufacturing has developed the best ultra-compact and light-weight hand carried AC load banks. AC load banks with capacities unmatched in the industry.
-
Product
HIGH-VOLTAGE TESTERS 0-10kV dc UP TO 0-50kV dc
DV-100VA-5V
-
HIGH-VOLTAGE TESTERS 0-10kV dc UP TO 0-50kV dc
-
Product
Load Pins
-
They are used in many diverse applications including cranes, winches, agricultural equipment (such as tractors), fishing, marine, offshore, subsea, aerospace, process industries, mining, hoisting gear, elevators and floor conveyors, cable laying machinery and many others. The load information provided by the pin can be used for process control, weight/force measurement, overload protection and safety related aspects.
-
Product
Programmable LED DC Electronic Load
M98 Series
-
M98 series DC electronic load, as a new generation product of Maynuo Electronic Co., Ltd, is designed for the LED driver application. A special circuit is desiged for the LED driver on the base of the M97XX sereies. Incorporating high-performance chips, the M98XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M98XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
Product
DC Power Supplies
SFA Series
-
AMETEK Programmable Power, Inc.
The SFA family builds on the industry leading Sorensen SGA series to provide a high power current source for laser diode applications. State of the art high power laser diodes require well-regulated current control to avoid catastrophic damage. Under anomalous operating conditions, excessive stored energy in the output circuit of the power supply can result in peak stresses that can permanently damage the device. Providing a constant current regulation mode only, the SFA’s low stored energy output minimizes damage potential for sensitive devices as well as enabling a current slew rate of up to 400 A/msec.
-
Product
Inductive Load Tester
4602-LV
-
There is a tendency that MOSFET has Low On Resistance so that it demands that Inductive Load Tester to have higher forcing current for measurement. The forcing current is limited by forcing voltage with previous test method. Thus it becomes difficult to test this kind of middle power range devices.
-
Product
DC Resistance Tester
DCSS502BC
-
Resistance meter is designed to measure copper resistance of transformers, wires, cables, other conductors and other coil products etc. It is widely used of low resistance measurement of switches, heater wires, transformers, relays, motors, electric films and PC circuit boards, wires, cables, etc. With reliable Good/ NG judgement, it is a premier resistance meter for the use in production line or QC department.
-
Product
Unclamped Inductive Load Tester
ITC75100
-
The ITC75100 is an enhanced unclamped inductive load (UIL) test system that builds on the success of ITC’s industry leading ITC55 series of testers by adding additional test and measurement capability.
-
Product
Programmable DC Power Supply
SPD1000X Series
-
SPD1000X Programmable Linear DC Power Supply has a 2.8 inch TFT-LCD display, features remote computer control capability, and real time wave display. This single output design is focused on delivering high performance and ease-of-use in a small package. The SPD1168 features a high precision programmable output capable of delivering up to 16 V/8 A,the SPD1305X features a high precision programmable output capable of delivering up to 30 V/5 A and also includes a 4-wire sense function for more accurate voltage sourcing, especially for long leads or high resistance connections. There are additional output short and overload protect functions to assist in production and development applications.
-
Product
DC Blocks
-
BroadWave designs and manufactures DC Blocks and other coaxial RF components that are ideally suited for test, verification and system integration. With frequency ranges of DC to 18 GHz, our components offer consistent performance at a low cost with an emphasis on performance and configuration flexibility.
-
Product
Beam and Singlepoint Load Cells
-
We have trimmed all the non-essential fat off these load cells, however you can be sure that nothing has been trimmed from the actual load cells, they are precision tested and certified to meet all the exacting requirements on the downloadable technical specifications shown below.
-
Product
Large Compressive Load Cell
CCLG-3.0
-
DLM’s range of Large Compressive load cells can be used independently or in combination as part of weighing platforms.
-
Product
DC SQUID System
-
Quantum Design's patented high-symmetry SQUID design and electronics provide the most rugged and sensitive all-thin-film sensors commercially available, and give you everything you need to configure flexible, powerful detection systems for your research. These sensors can easily withstand the rigors of a laboratory environment such as repeated temperature cycling. Their robust performance offers a level of reliability and adaptability that has earned QD a worldwide reputation as the SQUID of choice. OEM services are also available for special commercial applications.
-
Product
PXI MUX 8 Banks of 16 Channel 1 Pole
40-610-022-8/16/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
PXI 5 Banks of 16 Channel 2 Pole MUX
40-615-022-5/16/2
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
-
Product
Load Cells & Mounting Kits
-
Load cells are commonly used to measure weight in an industrial environment. They can be installed on hoppers, reactors, etc., to control their weight capacity, which is often of critical importance for an industrial process.
-
Product
Compression Load Cell
EST-20
-
Technopark Automation & Control
The EST-20 is an industry standard Compression Load Cell that can also be used in tension. This load cell can be supplied with load button and cup as well as ball and cup mounting options and is typically used on high capacity silos, hopper scales, batching systems, platform scales, force measurement and tension measurement applications. It is available in capacities from 1 ton to 50 ton.
-
Product
Programmable DC Electronic Load
-
Programmable DC electronic load is a device that precisely regulates the load voltage and current dissipation power consumption of electrical energy. There are several important parameters to consider when choosing programmable DC electronic load, including maximum power, maximum current, maximum voltage, current slope, and so on. Each indicator is related to the needs and applications we actually test.
