Wafer Resistivity
See Also: Wafer, Wafer Thickness, Wafer Failure Analysis, Wafer Edge, Wafer Mapping, Wafer Probes, Wafer Probers, Wafer Inspection, Four Point Probes
-
Product
Decade Box, Calibrated W/D & U, Resistance, 7, 1ohm to 11.11111Mohm, 1 %
72-7270 CAL DU
-
The 72-7270 CAL DU from Tenma is a resistance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set resistance value from 1 to 11,111,110 ohm in one ohm increments. The decade accuracy is ±1% resistors used throughout. It has weight of 320g/0.70lb and dimension 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
Product
Probe Needles for Wafer Sort and Test Applications
-
Advanced Probing Systems, Inc.
APS is the global leader in the manufacture of probe needles used in cantilevered probe cards. All probe needles used in wafer sort are manufactured according to customer specifications using stringent in-process quality assurance procedures.
-
Product
Insulation Resistance Tester for PV (2 range)
MIS-PV1
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
The model MIS-PV1 is an insulation resistance tester for the exclusive use in photovoltaic systems. The ordinary insulation resistance testers cannot make measurement properly during generation of PV systems. This instrument, however, can measure the insulation resistance simply by touching probe to the live line whether making generation or not. There are two ranges of PVH and PVL. PVH is for high voltage generation system (more than 500V and less than 1000V) and PVL is for the system less than 500V.
-
Product
Wafer Edge Profile Measurement
WATOM
-
WATOM can carry out fully automatic, non-contact measurements of the edge profiles and diameter in accordance with SEMICON standards. A special feature is the system's ability to make measurements of the mark cut into the edge of the wafer to indicate the crystal orientation. Because of its high measurement accuracy of less than 1.5 µm, leading wafer manufacturers across the world use WATOM for shop-floor geometrical quality control.
-
Product
Portable Wafer Probe Station
PS-5026B
-
High Power Pulse Instruments GmbH
The PS-5026B is a rugged portable wafer probing solution which has been designed for high reliability, compact size and minimum cost.
-
Product
Contactless Wafer Geometry Gauge
MX 20x series
-
The E+H geometry gauges are based on two heavy plates mounted parallel to each other. Embedded in the plate are a set of capacitive distance sensors. The wafer will be moved manual or automatically between the plates and measured without any movement.
-
Product
Ground Resistance Clamp Meter
61-920
-
*Auto ranging*Auto power off*Hard case included*2-year warranty
-
Product
Resistivity Cell For N1413 With B2980 Series (26/50/76 Mm Diameter Electrodes)
N1424C
Resistivity Cell
The N1424C is designed to operate specifically with the B2985B/87BElectrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424C to the B2985B/87B.
-
Product
Advanced Powder Resistance Kit
PRK-130
-
The PRK-130 is an advanced kit that includes the PRF-930 Powder Resistance Fixture for measuring the bulk resistance of powder and granulated materials. Test material is placed in the cavity between the measurement plates. Once a measurement has been made in ohms, a fixture calculation, or correction factor, converts the resistance measurement to volume resistivity in ohm-cm.
-
Product
Handheld Digital Multimeter, AC/DC Current, AC/DC Voltage, Capacitance, Resistance, True RMS
72-2995
-
40,000 count industrial True RMS digital multimeter is a highly versatile handheld instrument boasts 5-1/2 digit TRMS accuracy. It provides AC/DC voltage and current measurement, resistance, capacitance, temperature and frequency measurement, displaying readings on a backlit LCD digit and analogue bargraph display. Other features include non-contact voltage detection, continuity and diode test and USB data logging. All this is housed in a rugged overmolded enclosure with carry case, test leads and USB interface cable included.
-
Product
In-situ Wafer Temperature Monitoring
-
CI Semi's family of noncontact temperature monitors (the NTM line), offers high end pyrometry products for the measurement of wafer temperatures during process. CI Semi’s flag ship of the line, the NTM Delta, incorporates real-time, same point emissivity measurement and compensation making it the ideal solution for in situ monitoring for processes such as RTP, CVD and PVD. The NTM family is sold to leading tool manufacturers.
-
Product
Wafer Prober
Precio octo
-
200mm wafer prober. The system adapts ultra-high speed indexing and high-speed wafer exchange functions to reduce test cost and improve overall equipment effectiveness (OEE) markedly enhancing productivity.
-
Product
Decade Box, Calibrated, Resistance, 7, 1ohm to 11.11111Mohm, 1 %
72-7270 CAL
-
The 72-7270 CAL from Tenma is a resistance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set resistance value from 1 to 11,111,110 ohm in one ohm increments. The decade accuracy is ±1% resistors used throughout. It has weight of 320g/0.70lb and dimension 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
Product
Single-Phase Transformer Winding Resistance Meters
RMO-TT Series
-
RMO-TT series is perfect for measuring winding resistance of inductive objects such as power and distribution transformers or autotransformers. Additionally, every transformer resistance meter from RMO-TT series can analyze:tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.Transformer demagnetization can also be performed with all RMO-TT instruments.The series is consisted of 3 models, with maximal test current from 40 A (RMO40TT) to 100 A (RMO100TT). RMO100TT is the only portable transformer resistance meter in the market with 100 A DC output current.The three independent channels enable testing of three windings in series. Consequently, a user can measure winding resistance in every tap position of an on-load tap changer without discharging between the tests.In addition to winding resistance measurement, a user can perform a detailed on-load tap changer analysis by analyzing recorded graphs (10 kHz sampling rate) and by measuring vibrations on an external tap changer tank.All RMO-TT instruments have a built-in tap changer control unit. Because of this, it is possible to remotely control on-load tap changer (OLTC) directly from the device. Also, a user can program DV-Win software to do everything automatically – running winding resistance tests and changing OLTC tap positions.The DV-Win software also enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test.All results can be exported in the report format.
-
Product
3 Wire (Analogue) Earth Resistance Tester
2705 ER
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Battery check function.● Calibration performed with supplied test leads.
-
Product
Wafer ESD Tester lineup
-
Hanwa Electronic Ind. Co.,Ltd.
◆Correspond to 300mm Wafer. This tester can measure LED or the large sizes Wafer, such as a system LSI. And Zap of HBM/MM can be performed. The Automatic destructive judging by V/I measurement can also be performed after Zap.◆Waveform guarantee in Zap needles. HED-W5100D carries out the calibration before shipment in the place of Zap needles. Therefore, Correlation of the Result of a Package Device becomes clear easily.◆Correspondence to Standards This Tester corresponds to the Standard of JEITA, ESDA, and JEDEC. A Zap unit adopts the plug-in system and also has the waveform of Customer's requests.◆Connection with TLP This Tester is the best for TLP Testing with deep relation of ESD. The protection circuit of a device with an ESD problem is investigated.
-
Product
Ground Resistance Tester
-
Weshine Electric Manufacturing Co., Ltd
1.Soil resistivity tester supports 2, 3 and 4wire grounding resistance measurement. 2. 4digit large LCD display with white screen backlight, suitable for use in dimly lit places. 3. IP65 protection grade, good waterproof, compact and portable, supports multiple functional tests.
-
Product
PE-, Insulation Resistance, HV- and Function Tester
GLP1-g
-
GLP1-g testers are ideally suited for use in production, laboratory, test field, quality management, automation and many more applications. Thanks to the individual combination of functions you are able to reach your aims quickly, reliably and cost-effectively.
-
Product
Electrical Resistance (ER) Monitoring
-
The electrical resistance (ER) technique is an "on-line" method of monitoring the rate of corrosion and the extent of total metal loss for any metallic equipment or structure. The ER technique measures the effects of both the electrochemical and the mechanical components of corrosion such as erosion or cavitation. It is the only on-line, instrumented technique applicable to virtually all types of corrosive environments.
-
Product
Electronic Store Of Resistances
PS8
-
The module is intended for use as part of information measuring systems based on the VXI bus for software setting of resistance values with a given step along three independent channels.
-
Product
LED Type Wafer Alignment Sensor Controller
HD-T1
-
Panasonic Industrial Devices Sales Company of America
The HD-T1 Series is a new Wafer Alignment Sensor that uses a safe red LED light beam, with a resolution of 30µm, to achieve the same high level performance as Laser Sensors. The HD-T1 Sensor is best suited to detect wafer eccentricity, notches and orientation flats. Using linear image Sensor methodology and high-speed sampling technology, a wide variety of objects can now be stably measured with great precision at ultra-high speeds. This CCD style Sensor is developed for use in almost all fields of industry, e.g. tire manufacturing or Semiconductor production (Wafer Printed Circuit Boards).
-
Product
Wafer Sort
-
TestEdge offers complete wafer sort solutions. Our range of wafer sort capabilities demonstrates our ability to handle a wide range of devices and device characteristics. State of the art Electroglas probers Sort experience with high probe count Less than 4 mil pitch on probes Experience with C4 Bump and Aluminum pad Experience on Bipolar, CMOS, GaAs, & SiGe Overhead sort or cable harness sort Microsite testing capability
-
Product
Surface Resistance Meter Kit - Test Anti-Static, Static Dissipative and Conductive Surfaces
PRS-812RM
-
- Surface Resistance Tester from 0.10 Ω to 1 Teraohm- Constant Voltages 10 volts and 100 volts- Automatic Electrification Period- Determines if a surface is Dissipative, Conductive, or Insulative- Measures resistance point-to-point(Rtt) and resistance to ground (Rtg)- Measures resistance of ESD Flooring, ESD Worksurfaces and Packaging- Conforms to all ESD Association Standards for Resistive Characterization- Includes 2 each Surface Resistance Probes- Packaged in a hard shell Carrying Case- Certificate of Calibration Traceable to NIST included- 2-year Limited Warranty on Main Instrument
-
Product
Field thermal needle system for thermal resistivity / conductivity measurement
FTN01
-
Hukseflux Thermal Sensors B.V.
The FTN01 Field Thermal Needle System allows performing fast, on-site measurements of the thermal resistivity or conductivity of soils, in particular around the typical depth of burial of high voltage cables. FTN01 is designed with a focus on robustness and saving time, while still offering sufficient accuracy for typical field measurements. The sensor is a Non-Steady-State Probe (NSSP), TP09, which is mounted at the tip of the Lance LN01. The system is operated using a hand-held Control and Readout Unit CRU01.
-
Product
2-Way Resistive Power Dividers DC To 40 GHz
-
Pulsar Microwave manufactures resistive dividers from DC to 40 GHz. They have a rated input power of one half watt maximum. VSWR of 1.5:1 or better maintained throughout band at all ports. Resistive dividers can be fitted with SMA male or female connectors and are available in three outline packages.
-
Product
Wafer Prober
Prexa MS
-
The latest fully automated 300mm wafer prober for memory devices. Featuring high rigidity and exceptional thermal control, the system enables full-wafer contact testing.
-
Product
BT Imagine New wafer Thickness System
IS-T1
-
Measurement Technique Laser Triangulation1-3 Laser Sensor SpotsLaser Spot Size Optimized for Accuracy and Precision.
-
Product
3 Wire (Digital) Earth Resistance Tester
1120 ER
-
Standard Electric Works Co., Ltd
● Waterproof: IP54● Capable of measuring earth resistance and earth voltage● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test● The test leads are supplied as standard accessories for simplified two-wire measuring system● 0Ω adjustment● Battery operated● Data hold function● Low battery indication
-
Product
Internal Resistance Testers
-
The Battery Internal Resistance Tester is essential for assessing the health and performance of stationary reserve power batteries. Designed for efficiency, this tester measures internal resistance, helping to identify potential issues before they impact battery performance. By providing accurate diagnostics, it enables proactive maintenance, ensuring reliability in critical applications. This advanced testing equipment is an invaluable tool for enhancing battery longevity and optimizing energy storage systems.
-
Product
Non-contact Sheet Resistance Multi-points Measurement System With Wide Range
NC-80MAP
-
*Possible to measure wide range of sheet resistance by installing Max. 4 probes*Min. 7 mm position from edge can be measured*User programable measurement pattern & programmable measuring pattern
