-
Product
Multi-Cell Test System
Cellcia
-
Next-generation wafer probing system for 300mm wafers. The multi-layer system structure maximizes the efficiency of testing, further reducing the total testing cost.
-
Product
Consumables
-
QATM offers a wide range of high-quality consumables for metallographic sample preparation and analysis. All consumables are thoroughly tested and selected for perfect interaction with QATM machines.
-
Product
Battery Test Packages
-
Explorer Technology Group (ETG)
ETG offers a full range of battery test kits which speed and simplify the process of collecting battery test data . This data can then be downloaded and analyzed with the included Winmeter 5.1 Battery Analysis Software, enabling the user to quickly identify batteries that are likely to require preventative maintenance.
-
Product
Electrolyzer Test Systems
-
Advanced Test System for Research & Development of PEM Electrolyzers
-
Product
4/8 Channel 1.0 ~ 30.0 Gb/s Pulse Pattern Generator and Error Detector
CA9808C
-
The UC INSTRUEMNTS CA9808C 4/8 Channel 1.0 ~ 30.0 Gb/s pulse pattern generator and error detector is a high performance, flexible and cost effective four channel Pulse Pattern Generator and Error Detector that can operate from 1.0 Gb/s to 30.0 Gb/s each Channel. 4/8 channel 30.0 Gb/s make it total up to over more than 120/240 Gb/s testing capacity. It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer.
-
Product
R.F. Coupler and high Pass Filter
7415-3
-
There are those who disagree with the r.f. conducted susceptibility test setup of Method CS02 of MIL-STD-462. Homemade rigs have sprouted to comply with the coupling capacitor requirement, each with it own disadvantage. Our little Type 7415-3 R.F. Coupler is the answer. A neat little box with BNC connectors and a pair of binding posts, it is rated at 270 V.A.C. at the LINE terminals and 20 volts PMS into the GEN port. Looks good and does a fine job.
-
Product
Photonics Module Test System
58625
Test System
Chroma 58625 provides characterization testing for 3D sensing illumination devices. various test modules are combined for validation testing under precise temperature control.
-
Product
Basic Power Supply - 80 W Max Output Power
NGA100
Power Supply
The R&S®NGA100 DC power supplies are linear, compact and easy to use in diverse scenarios. All models have excellent readback accuracy with a low-current range for demanding measurements. Data logging, arbitrary waveforms, built-in statistics and remote sensing features make the instruments ideal for various bench applications, such as:- R&D;- Creating IoT low power designs - Manufacturing- Education- General purpose use casesEquipped with a number of different remote interfaces, including USB and Ethernet, R&S®NGA100 DC power supplies are also great for automated tests. The channel fusion feature extends voltage and current range. Get up to 200 V with the R&S®NGA142 in serial mode and up to 12 A with the R&S®NGA102 in parallel mode. Advanced protection functions keep devices connected and power supplies safe.Choose the DC power supply for your use case by selecting the base unit and necessary options in our online configurator. This makes the procedure easy and fully price transparent for fast processing of your order request by our authorized distribution partners. Click "configure and quote" to start your configuration.
-
Product
Electrostatic Discharge Simulators
ESS Series
-
EMC test equipment to evaluate the resistibility of electronic equipment when electrostatic charges on a human body or object has been discharged to the electronic equipment.This product can be used for evaluating performance degradation of any types of electronic products.
-
Product
STANAG3910 Test And Simulation Module – Rafale – For PCI Express
APEX3910-EN
Simulator
Single Stream STANAG3910 Test and Simulation module – Rafale – for PCI Express with 1 dual redundant HS/LS channel and onboard Electrical Front End (EFE). The APEX3910-EN is a functional replacement for APE3910-EN.
-
Product
Repeat Durability Tester
TIQ1000
-
It is a device to measure repeated endurance such as limit bending test of board, endurance test of mounted board, endurance test of connector, etc. Continuity data and load data can be obtained during the cyclic endurance test. Conforms to JEITA ET-7407 "Environmental and durability test methods for mounted CSP/BGA packages".
-
Product
Comparative Tracking Index Apparatus
CTI-01
-
Is designed to perform the test specified in many standards where resistance to Tracking in insulating partssupporting live parts is required to be established.
-
Product
Test Connector Components
-
Any flat substrate, or bumped substrate, can be compressed against Z-Axis Elastomeric Connectors to make contact. The picture illustrates a Z-Thru Z-Alloy Connector Frame used to connect the DUT (Device Under Test) to a circuit board.
-
Product
Vibration Testing System
-
Wewon Environmental Chambers Co, Ltd.
Vibration Testing is performed to determine if a product can withstand the rigors of its intended use.
-
Product
40 MHz, 1.2 GS/s, 8 Mpts, 2 Ch, 20 Vpp Function/Arbitrary Waveform Generator
T3AFG40
Arbitrary Waveform Generator
Teledyne Test Tools T3AFG5 and T3AFG10 series Function/Arbitrary Waveform Generators are a new family of low cost, high performance, single channel Function / Arbitrary waveform generators offering a high level of functionality and an excellent specification at a very competitive price point.
-
Product
10G Ethernet Emulator
VirtualNetTM XG
-
VirtualNet-10G is a high-performance Network Emulator that replicates real world Ethernet network effects such as latency and errors on user traffic in a controlled environment. The VirtualNet-10G emulator uses customized ICs to support full line rate performance at all frame sizes and impairment settings. The emulator can be transparently installed in-line as shown in the diagram below. VirtualNet-10G emulator has an intuitive and easy to use GUI interface and a very powerful TCL based CLI to aid in configuration and testing.
-
Product
Clamping Voltage Tester
MIG0603CLV2
-
The MIG0603CLV2 is a generator for clamping voltage testing of varistors. It has circuits with four different source impedances and up to 15 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 500A which is maintained over the entire load range.
-
Product
Storage & Recording
-
Curtiss-Wright Defense Solutions
Whether you need rugged data storage modules for reliable data storage, SWaP-optimized network-attached storage (NAS) systems, crash-protected cockpit voice and flight data recorders, test and monitoring recorders, or video recorders, Curtiss-Wright is your one-stop for trusted, proven solutions.
-
Product
Microfluidic Device Manufacturing Solutions
-
We provide production automation solutions for microfluidic device manufacturing with precise liquid dispensing. We offer solutions for your POC test, molecular and immunodiagnostics and microfluidic devices manufacturing.
-
Product
I/O Input/Output Board
VME-4514A
-
The VME-4514A Analog I/O (AIO) Board provides 16 high-quality analog output channels which can be programmed with on-board jumpers to operate in a variety of voltage ranges. Each output can source or sink 10 mA at ±10 V. For off-line testing, the analog outputs can be disconnected from the I/O connector.
-
Product
PXI High-Density Matrix Switch: 4x64, 2-Wire, 100Vrms/0.5A, Reed Relays
M9121A
Matrix Switch Module
The M9121A is a 4x64 full crosspoint switch matrix offering high-density, high-speed signal switching in a single PXI module. The 2-wire matrix allows multiple channels to be connected in a single instance. Any row can be connected to any column, making it ideal for routing instrument signals to the device under test. This 2-wire switch matrix provides the high-speed, long-life reed relays to support signal switching up 100Vrms with 10W maximum power. The 4-wide bus is ideal to route signals between test instruments and the device under test. Choose from the durable connector block or standard cable connections.
-
Product
EOL Tester
-
Sterner Automation would like to introduce its new end of line (EOL) tester platform. Sterner Automation has been a supplier of calibration and test equipment to the automotive industry for over a decade and is now offering a standard hardware EOL platform that is configurable with a variety of software modules for seating plant applications.
-
Product
Electronic Ballast Tester
WT4000
-
• Measure parameter: 1) Input: Vrms, Lrms, W, PF, Hz, Phasic angle, total harmonic and 0-39 component of harmonic. 2) Output: Lamp voltage, Lamp current, Filament current, Guided cathodic current, Lamp power, crest factor and oscillatory frequency, single high frequency analysis. • Startup: Startup lamp voltage, lamp current, filament current, guided cathodic current curve and parameter, preheating time; • Simultaneously display on 8 windows for input and output parameters, convenient for comparison and analysis; • Test preheat energy, filament preheat time. And the parameters changes from 0 to 5s of filament voltage, filament current and filament power; • Up to 1MHz lrms test content to every EB; • Analysis symmetry of high Frequency curve of lout; • 12-bit high-speed A/D, sampling rate up to 10MHz, can easily analyse signal curve of output; • Finish an input and output testing at the same time within 1 minute; • Portable, can test, display, print without computer. Test report include data and curve, comply with international standard; • Communication port for PC, run under Windows98 or Windows2000, English Version available.
-
Product
Fire & Flammability Test
-
Fire & Flammability testing: ASTM E119 [UL 263]; ASTM E152 [UL 10C]; ASTM E814 [UL 1479]; API 607, 6A; ASTM E108 [UL 790]; UL 1709; UL 1715; UL 2043; NFPA 286; UBC 26-2; UBC 26-3; ASTM E84 [NFPA 255, UL 723]; ASTM E162; ASTM E662 [NFPA 258]; ASTM D635; ASTM D1929; ASTM D2863; ASTM E1354; ASTM E1317; Room Burn Facility; CAL 133, 117, 129; UL 94 V/HB; IMO A.652 (16); IMO A.653 (16); ULVW I; ASTM D2859; AITM 2.0007; NFPA 701; FMVSS 302; FAA 25.853; IEEE 383
-
Product
Meter Test Systems
-
We offer a huge variety of products for meter testing. From the smallest device with the size of a single-phase meter up to customized semi-automatic systems with more than 40 test positions.
-
Product
Inspection Tools
Multi Disk Test System (4-Port)
-
16 types of inspection modes can be registered and edited. More accurate acceptance inspections can be performed using various types of inspections.High speed data communications using USB interface for communicating with host computer.Acceleration testing for temperature loaded HDD can also be performed. (Optional)Easy attaching and removing HDD using optional plug-in unit.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 255 Ohm
50-293-013
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Spectrum Analysis, Up To 26.5 GHz
S930902B
-
The S930902B spectrum analysis adds high-performance microwave spectrum analysis to the PNA family up to 26.5 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Simultaneous spectrum measurements can be done using up to five test and reference receivers. This multi-channel SA can be used with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
Product
Test Automation System for Driveline Testing
STARS Driveline
-
STARS Driveline is an integrated automation, acquisition and control system that provides a broad range of application functionality in a single, powerful environment. It has been designed to fulfil the specialist requirements and applications for driveline testing from simple modal testing on two or four wheel drive systems, to RLS simulation or advanced applications such as service load replication (SLR).
-
Product
Cable Fault Locator System
-
Kvtester Electronics Technology Co.,Ltd
To test the HV arcing fault of cable, earthing high &low resistance, short circuit and breakage of the cable, poor contact, etc. If equipped with fault locator, it can decide the exact broken position of the cable ,applies to power cable in various type, voltage and communication cable
