-
Product
Power Switches
SMX-2002 (Power)
-
The SMX-2002 is the only switch module in its class with the ability to switch up to 16A. Some applications include: AC line power switching, switching of DC or AC power supplies, control or driving relays for industrial machines (robotics, numerical control machines), automotive engine control, and solenoid switching. Since this module typically switches power to the UUT or interface, the SMX-2002 includes failsafe pins on the front panel which can be configured to open all relays when a failsafe signal is activated. This approach can instantly removes all power to the UUT or interface.
-
Product
Protected & Intelligent Power Switches
-
Single/Dual high-side output with optimized protection function and analog current feedback for body, lighting and heater applications.
-
Product
Intelligent Power Switches
-
ST offers a series of intelligent power switches (IPS) for high-side and low-side configurations. These devices integrate the control section (logic interface, drivers, diagnostic and protection features) and the power stage on the same chip, with benefits in terms of compactness, increased system reliability and cost effectiveness.
-
Product
Power Rocker Switches
-
Panasonic Industrial Devices Sales Company of America
Power Rocker Switches for safety requirements complying with Class II EN61058-1 insulation grade. 8mm minimum insulation distance and 3mm minimum contact gap. Applications include: Vehicles, Home Appliances, Outdoor Power Equipment, Agricultural, Industrial Equipment.
-
Product
RF Power Switches
-
Multi-Tech specializes in RF power applications. Seven models available from 2000 volts/20 amps peak to 24,000 volts/100 amps peak. Insulating materials are L5 grade steatite; all current carrying components are heavy silver plated. All switches are custom made to our customers' specifications. Mil-spec SR05 style sub-miniature and low voltage rotary switches, hardware, and switch components are also available.
-
-
Product
Switched Power Distributed Module, CAN Control
H730008xS
Power Module
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions: Distributing the power to each device in a system Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.
-
Product
PXI Solid State Switch Module, 6xSPST, 10 A, Hardware Interlock
40-182A-011-HI
Switch Module
The 40-182A-011-HI has 6 off high current SPST switches with hardware interlock in two PXI slots and is part of our range of high power solid state switching solutions.
-
Product
PXI 2A 39xSPST High Density Power Relay Module
40-137-201
Relay
These Power Relay Modules are suitable for applications requiring power relay switching with high density. The feature 2A current and voltage to 110VDC/250VAC, they are configured as Single Pole Single Throw (SPST). Connections are made via front panel mounted 37 or 78-pin D-Type connector.Along with this 39 x SPST version, the range also includes a 32 x SPST, 2A version and a 16 x SPST, 5A version - go to Also in the Range above to learn more.Typical applications will be found in Automotive Test, Aerospace Test and Power Cell Test applications.
-
Product
PXIe Power Relay Module, 10xSPST, 16 A, With Interlock
42-161A-003-HI
Relay
The 40/42-161A-003-HI is a PXI/PXIe 10xSPST power relay modulewith optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
Modular Designed CAMAC
CAMAC CERN-CE 1920W
-
WIENER provides a line of modular designed CAMAC crates compliant with ESONE and CERN standards. These CERN spec. CAMAC crates are configurable with linear regulated, low noise plug-in power supplies in the 300W ... 600W DC power range or up to 1900W with PS236 low-noise switching power supplies.
-
Product
PXI 24xSPST High Voltage Power Relay Module
40-330-001
Relay
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.
-
Product
High Power Switch and Bias Module
-
Macom Technology Solutions Holdings Inc.
MACOM’s High-Power Switch and Bias modules are extensively used in 4G and 5G TDD base stations as well as aerospace and defense applications. The PIN Diode Switch features high power handling, low insertion loss, and super board band performance. The integrated bias controller utilizes a boost circuit and provide the driver circuitry to the switch. The modules require only a single 5 V supply, and a single TX / RX control signal which greatly reduced the customer design complexity.
-
Product
LED Drivers led Switching Power Supply
-
Dongguan Longwei Electronic Technology Co., Ltd.
LED drivers led switching power supply
-
Product
30 Amps, 50 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP030
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
20-Channel SPST Power Switch Card
1260-120
Switch Card
Each channel of the 1260-120 can switch up to 13A, 250VAC or 10A, 125VDC; its switching capability makes it the ideal solution for applications requiring high-current switching of AC power, DC power supplies, and AC or DC current sources.
-
Product
150 A, 5 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 6 Meter Cable
CP150-6M
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
PXIe Power Relay Module, 12xSPST, 16 A
42-161A-002
Relay
The 40/42-161A-002 is a PXI/PXIe 12xSPST power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
Signal Conditioner
SGA
-
Versatile signal conditioner featuring user selectable outputs of +/-10V, +/-5V, 0-10V, 0-5V, 0-20mA and 4-20ma. DC or AC powered with switch selectable filters from 1 to 5kHz and a sealed ABS enclosure. Supports shunt calibration and a wide range of gain settings.
-
Product
AC/DC Current Probe, 50 MHz, 15A
1147B
Battery Probe
The 1147B is ideal for capturing transient current signals such as those found in motor controllers, switching power supplies, inverters and current amplifiers driving inductive loads.
-
Product
Chassis - Control Relays Greater than 8x1 or Control Multiple Relays in Series Forming Larger Switches than Normally Possible Such as 16x1 to 32x1 Sections.
CXM/256-MF
Chassis
These Chassis are typically used to control relays greater than 8x1 or control multiple relays in series forming larger switches than normally possible such as 16x1 to 32x1 sections. Or control mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 256 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
Product
ArgoBot Kit
ROB-00001
-
The ArgoBot Full Kit is a fully assembled robot and controls development platform. It is based on the Digilent chipKIT WF32(TM), a WiFi enabled development platform, and configured for LabVIEW targeting. Most importantly ArgoBot was designed with FIRST Robotics Competition teams in the front of our minds! Named after the FRC Team 1756 mascot, Argos, the ArgoBot development platform includes a fully-assembled, ready to drive mini WiFi enabled robot (about 8" x 5" x 4"), as well as tons of FRC controls tutorials and example code (LabVIEW VIs). Features included on the ArgoBot will look very familiar to anyone who has worked with National Instruments products (Compact RIO and RoboRIO) in the past. This includes three 5V Digital I/O modules (with jumpered pull-ups), three 5V analog inputs, and an I2C header. Example VIs have been streamlined to enable a 1-click configuration style to accelerate your development process. We also added a 2-channel motor driver that is used to supply the ArgoBot drive motors. Our ultimate goal is that everything you can build, control or implement on ArgoBot can be easily leveraged on your FRC bot! Complimenting its many electrical features, ArgoBot is easy to work with and easy to maintain. The chassis is a polycarbonate (the extremely tough stuff that is easy to drill and modify but easily takes bumps and bruises without cracking) case that is fully intact - meaning that ArgoBot doesn't just come with a case... it is a case! Clean-up and organization is simple - just close the case and turn off the power switch.
-
Product
MSR160 Data Logger with Analogue Inputs
MSR160
-
Four integrated analogue inputs, a high measurement rate of up to 1000/s per channel and its gigantic memory capacity, all packed into a small format are the key characteristics of the MSR160 data logger. The analogue inputs of the robust mini logger can be used for conventional sensors with analogue outputs (e.g. CO2, conductivity, pH etc). In addition, a multiple output switching power supply is also provided.
-
Product
Switch Indication Maintainer Plus
The SIM-Plus
-
The SIM-Plus - Switch Indication Maintainer Plus is a handheld device used to simulate normal switch correspondence while performing periodic maintenance or testing. The SIM-Plus also provides the ability to power the switch machine using local switch battery or, if battery is not available, provide a temporary source of power from an optional power pack.
-
Product
Programmable Switching Power Supplies
-
PeakTech Prüf- und Messtechnik GmbH
In addition to presets for current and voltage values, time programs with intervals and the number of runs can also be created directly on the device or using the included PC software. For operation with a PC, the switching power supply is equipped with a USB and RS-485 interface. A PC connected to the RS-485 interface enables the control of up to 32 power supplies. A USB interface on the back of the device connects to a Windows PC. The intelligent fan control adjusts the speed of rotation to the respective temperature and output power. The output voltage and current limit can also be set in the open circuit without a connected load. Due to its high reliability and the programming functions, this power supply series is ideal for professional users from industry, control and regulation technology or the electronics laboratory.
-
Product
PXI Mixed Configuration Relay Module - 7 Cells Populated
40-138-AA-BB-CC-DD (7 CELL)
Relay
The 40-138 2A Relay Module with 7 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
Power Switches With USB Charge Controller
-
ST’s USB charger emulator family (STCC) features ICs integrating a power switch, a data switch and an intelligent charge controller. It supports most charging schemes on the market (standard and proprietary) to ensure compatibility with a broad range of portable devices. ST’s unique and patented attach detection mechanism makes the STCC family ideal to guarantee fast and accurate charging while preserving the host battery.
-
Product
PXI 12xSPDT 16A Power EMR Module
40-161-101
Relay
This40-161 range of PXI power relay modules is available with achoice of 16 x SPST, 12 x SPST, 10 x SPST, 12 x SPDT and 6 x SPDT power relays, for switching loads up to 16A at250VAC. These Power Relay Modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. The 40-161 is ideal for switching up to 16A in both AC and DC applications.
-
Product
Intelligent Power Devices
-
Intelligent Power Devices have built-in peripheral and protection functions, and support system reliability improvement and unit downsizing. This device lineup can support a variety of automotive system requirements and includes intelligent power switches, thermal FETs, MOSFET drivers, and a motor driver.
-
Product
SP8T RF Pin Diode Switches To 12 GHz
-
Pulsar Microwave manufactures 8-way absorptive and reflective RF switches in single-pole 8-throw configuration. They fulfill broadband and narrowband requirements from 40 MHz to 12 GHz and handle 200 milliwatts input power. The SP8T switches have an isolation of 60 dB and switching time of 100 ns. Most models specify 1.6:1 or better VSWR at all ports. The SP8T switches operate on a power supply of +/- 5VDC and switching control is 0-5 TTL logic. The unit comes standard with SMA female connectors. Options for control are line drivers and decoders.
