Programmable Switching Power Supplies
-
Product
DC Power Module, 8V, 12.5A, 100W
N6742B
Power Module
The Keysight N6742B is a 100 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
E-Series Peak and Average Power Sensor, 50 MHz to 6 GHz
E9322A
Power Sensor
The E9322A power sensor has a 1.5 MHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA and CDMA wireless formats such as Bluetooth.
-
Product
PCI High Density Potentiometer Card 4-Channel, 12-Bit, 0 To 4k Ohm
50-296A-121-4/12
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Power, Patchcord, Receiver, 36", Mini Power, 16 AWG White
7-242956000-036
Power Patchcord
Power, Patchcord, Receiver, 36", Mini Power, 16 AWG White.
-
Product
Power Divider, DC to 18 GHz
11636A
Power Divider
The Keysight 11636A is a dc to 18 GHz power divider for direct power dividing applications. The excellent impedance match of all three ports improves fault location measurements by reducing re-reflections. The Keysight 11636A power divider/combiner is recommended when making wideband comparison measurements with a Keysight 8757 scalar vector network analyzer.
-
Product
Power Limiter, 0.01 to 26.5 GHz
N9355C
Power Limiter
The N9355C power limiter provides the best broadband input power protection to sensitive RF and microwave instruments and components, like network analyzers, spectrum analyzers, and amplifiers, from excess RF power, DC transients and ESD. Minimize your measurement uncertainty and improve your measurement accuracy with the limiter's superior RF performance.
-
Product
EPM Series Dual-Channel Power Meter
N1914A
Power Meter
Frequency range of 9 kHz to 110 GHz (sensor dependent)Wide dynamic range of -70 to +44 dBm (sensor dependent)Speed improvement by 2X for E-Series sensors: up to 400 readings/secGo beyond GPIB with LAN LXI-C and USB connectivity Code-compatible with E4418B, E4419B power meters*Code-compatible with 436A, 437B and 438A power meters (option 200)Increased measurement channels: up to three channels with two additional U2000 Series power sensors connected using the optional USB hosts Automated frequency/power sweep measurements with the optional external trigger in/out feature
-
Product
10 MHz To 67 GHz USB Wide Dynamic Range Average Power Sensor
U2057XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
PXI High Density Precision Resistor Module, 3-Channel, 4Ω to 22.3MΩ
40-298-154
Programmable Resistor Modules
The 40-298-154 is a high density programmable resistor module with 3 channels which can be set between 4Ω and 22.3MΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Waveguide Power Sensor
E8486A
Power Sensor
Keysight waveguide power sensors are fully compatible with Keysight EPM (E4418B/19B, N1913A/14A), EPM-P (E4416A/17A) and P-Series (N1911A/12A) power meters. The V8486A and W8486A are also compatible with the discontinued or obsolete power meters such as 435B, 436A, 437B, 438A, 70100A, E1416A, E4418A, and E4419A power meters.
-
Product
Thermocouple Power Sensors
N8487A
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm - SPST
50-294-121
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Precision Resistor Card 3-Channel, 3Ω To 22.3MΩ
50-297-154
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Resistor Card 5-Channel, 16-Bit, 0 To 65k Ohm
50-295A-021-5/16
Programmable Resistor Modules
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-040
Programmable Resistor Modules
The 40-297A-040 (PXI) and the 42-297A-040 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm - SPST
40-294-111
Programmable Resistor Modules
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Power Splitter, DC to 18 GHz
11667A
Power Splitter
The Keysight 11667A power splitter is recommended when making wideband ratio measurements using a Keysight 8757 scalar network analyzer. This two-resistor type power splitter provides excellent output SWR at the auxilliary arm when used for source leveling or ratio measurement applications. The tracking between output arms over a frequency range from dc to 18 GHz allows wideband measurements to be made with a minimum of uncertainty.
-
Product
DC/DC Power Supply
ISM-DC-AT512-P
DC Power Supply
The ISM-DC-AT512-P is a dual output, DC/DC power supply designed for small form factor embedded systems. It features a very wide voltage input range from 10 to 50 volts DC. This allows the unit to operate with 12, 24, or 48 volt battery or distributed DC power systems. It opens up a wide array of applications including transportation, Mil/COTS, security, solar-powered, and telecommunications.
-
Product
Advanced Power System – Power Dissipater Unit, 1000 W
N7909A
Power Divider
The N7909A power dissipater unit adds current sinking or two-quadrant operation to any Advanced Power System (APS) N6900A or N7900A power supply. Each N7909A provides up to 1 kW of current sinking capability to an APS power supply, so you will need two N7909As to achieve full two-quadrant operation of a 2-kW APS supply. You can use a single N7909A unit with a 2-kW APS power supply to achieve 50% current sinking capability. The N7909A form factor is 1U and full rack width. N7909A connects to an APS power supply via a two-wire power connection and a communication connection to provide continuous two-quadrant operation. The connections are located on the rear panel of both the N7909A and the supply.
-
Product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-043
Programmable Resistor Modules
The 40-297A-043 (PXI) and the 42-297A-043 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 773 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
P-Series Wideband Power Sensor, 50 MHz to 40 GHz
N1922A
Power Sensor
Peak, peak-to-average ratio, average power, rise time, fall time, maximum power, minimum power, and statistical data of wideband signals.
-
Product
PXI 10W Programmable Resistor Module, 2-Channel, 1Ω to 31.5Ω
40-253-010
Programmable Resistor Modules
The 40-253-010 is a programmable resistor module with 2 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Thermocouple Power Sensors
N8481B
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
Power, Patchcord, ITA, Micro Power, 36", 14 AWG White Teflon, Single Ended, (22 Amps)
7-251914000-036
Power Patchcord
Power, Patchcord, ITA, Micro Power (22 Amps), 36", 14 AWG White Teflon, Single Ended, (30 Amps)
-
Product
PXI Power Supply 1 Channel 40W 48V 2A
PS48401
Power Supply
The PS48401 is a programmable DC power supply in a 2-slot PXI/cPCI form factor. It features a fully isolated output capable of delivering 0-48VDC / 2A / 40W. It offers a programmable current limit and the ability to measure the output voltage and current under software or trigger control.
-
Product
PXI Precision Resistor Module 6-Channel, 2.5 to 201k
40-297-041
Programmable Resistor Modules
This 6-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
E-Series Peak and Average Power Sensor, 50 MHz to 18 GHz
E9326A
Power Sensor
The E9326A power sensor has a 1.5 MHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA and CDMA wireless formats such as Bluetooth.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm
50-293-012
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI-2720, 8-Bit, 10-Channel PXI Programmable Resistor Module
781985-20
Programmable Resistor Modules
8-Bit, 10-Channel PXI Programmable Resistor Module—The PXI‑2720 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2720 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-140
Programmable Resistor Modules
The 40-297A-140 (PXI) and the 42-297A-140 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
