CF
Flash technology storage that retains data without a battery.
-
Product
Mini-ITX Embedded Board with 8th/9th Gen Intel® Core™ i7/i5/i3 Processors
AmITX-CF-I
Motherboard
The AmITX-CF-I is a Mini-ITX motherboard supporting the 8th/9th Gen Intel® Core™ i9/i7/i5/i3, Pentium® and Celeron® processor in the LGA1151 package, and the Intel Q370/H310 chipset. The AmITX-CF-I is specifically designed for customers who need high-level processing and graphics performance with a long product life solution. This model supports ubiquitous high-speed data transfer interfaces PCIe 3.0, USB 3.1 Gen2 and SATA 6 Gb/s (SATA III), with dual-channel DDR4 2400/2666 MHz non-ECC memory up to 32 GB in two SODIMM slots. The AmITX-CF-I features DVI, DP and HDMI ports, LVDS header, dual Gigabit Ethernet ports, USB 3.0 ports, USB 2.0 ports, SATA 6 Gb/s ports, and audio with Line-out, Line-in and Mic-in connectors. Expansion is provided by one PCIe x16, one M.2, and one mini-PCIe slot. The onboard pin header provides GPIO, USB and RS-232 support. The board is equipped with SPI AMI EFI BIOS, supporting embedded features such as hardware monitor and watchdog timer.
-
Product
Pre- Locator
CFL PL3+
-
The new generation CFL PL3+ Cable Fault Pre-locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 128 km.
-
Product
Exhaust Fan
CF-400-X
-
This UL approved exhaust fan is typically installed in cabinet top panels, but has many applications. This fan requires a 10” diameter area and extends approximately 4” inside the panel.
-
Product
Audio Fiber Tracer
CFT-810
-
Motorized Polarization Controller. In addition to its basic function of adjusting polarization states in multi channels, it also provides convenient ‘save and recall’ functions. As a Scanning PC, it provides very powerful ‘auto scan’ modes with variable scanning speeds. Polarization states can be manipulated by either manual adjustment or remote control (GPIB, RS-232) using two quarter-wave plates in each channel of the PC1600. Additionally, the auto scan mode of FIBERPRO’s Motorized Polarization Controller has been upgraded in LPC, and it shows another auto scan mode of four quarter-waveplates with higher polarization extinction ratio when connecting two channels at a high speed. PC1600 is an essential tool to complete fiber-optic, multi-channel measurement systems such as WDM/DWDM as well as R&D (i.e. PMD experiments), and manufacturing.
-
Product
Pre- Locator
CFL PL2+
-
The new generation CFL PL2+ Cable Fault Prelocator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 50 km.
-
Product
Pre- Locator
CFL PL3
-
CFL PL3, new generation Cable Fault Pre-Locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault with accuracy.
-
Product
Pin Pointer
CFL PP3+
-
The new generation CFL PP3+ Cable Fault Pin Pointer cum route tracer from SCOPE is the ultimate solution for locating of underground cable faults in minimum time by tracing cable route. It uses an advanced technology which helps even an unskilled operator to locate the fault accurately.
-
Product
Tubeaxial Fan
CF-90
-
This tube axial fan delivers higher CFM yet only requires 4.7” x 4.7” area including the grille.
-
Product
Free Measurement System
CFMS
-
The Cryogen Free Measurement System (CFMS) from Cryogenic Ltd is a modular research system designed to enable the user to perform a wide range of material characterisation experiments in variable field and variable temperature environments.
-
Product
COM Express® Basic Size Type 6 Module with Up to Hexacore 8th Gen Intel Core™ 8000 Series and Intel Xeon® Processors (formerly codename: Coffee Lake-H)
Express-CF/CFE
Computer on Module
The Express-CF/CFE is the first COM Express® COM.0 R3.0 Basic Size Type 6 module supporting the Hexa-core (6 cores) 64-bit 8th Generation Intel® Core™ and Xeon® processor (codename “Coffeelake-H”) with Mobile Intel® QM370, HM370, CM246 Chipset.
-
Product
Computational Fluid Dynamics
CFD
-
Computational Fluid Dynamics analysis is a value-added service from Teledyne Cormon that predicts pipeline flow and sand particle behavior for specific project scopes, allowing asset integrity teams to understand the optimal placement for erosion and corrosion monitoring probes.
-
Product
AC Power Source
61600 Series
-
Built-in PFC, provide input power factor over 0.98 (full load)AC+DC output mode for voltage DC offset simulationProgrammable voltage,current limitComprehensive measurement capability,V, Hz, Irms, Ipk, Iinrush, P, VAR, VA, PF, CF of current and etc.High output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlOne-key recall for 9 different voltage and frequencyProgrammable slew rate setting for changing voltage and frequencyAnalog input for power amplifierOptional Analog programming interfaceOptional GPIB and RS-232 interface(Model 61601~61605)Full protection: OP,OC,OV and OT protectionEasy use graphic user interface: softpanel (option)Capable of delivering power output up tp 90KVA by implementing Master-Slave operation
-
Product
Crossed-Field Amplifiers
CFAs
-
Communications & Power Industries
CPI BMD’s crossed-field amplifiers (CFAs) are broadband, phase-stable microwave amplifiers used in coherent radar chains to efficiently generate very high peak output powers from relatively low input voltages which can be either applied to the cathode or an electrode similar to a TWTs cathode or grid pulsing, and in relatively small, lightweight packages. These characteristics make CFAs particularly well-suited for applications in which the transmitter must be either airborne, transportable, mobile or portable.
-
Product
AC and DC Power Sources
CFS100 Series
-
The CFS100 Series programmable AC or DC output power sources are cost effective source of power for development, test and production applications requiring anywhere from 800VA or less to 4000VA of single phase AC or DC output.
-
-
Product
CAMAC-to-FERA Bridge
CFB
-
The WIENER CFB is an intelligent, programmable, re-configurable CAMAC-to-FERA bridge with sequencer that allows one to interface both, common and custom-made CAMAC modules to FERA-readout-based data acquisition systems.
-
Product
Modular TDM / IP Split Mount Radio System
CFIP PhoeniX M
-
CFIP PhoeniX M split mount system consists of PhoeniX M IDU and PhoeniX ODU (XPIC functionality supported). PhoeniX M IDU provides up to 63E1 and 2xSTM-1 bringing the total maximum capacity to 348 Mbps full duplex.
