Product

3 Wire (Digital) Earth Resistance Tester

1620 ER

-

Standard Electric Works Co., Ltd

1620 ER - Standard Electric Works Co., Ltd

● Microprocessor-controlled.● Measures earth resistance in three ranges : 40Ω, 400Ω, 4kΩ.● Capable of measuring earth voltage.● 3 ¾ digit (4000 counts).● LCD backlight display.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Data hold function.● Relative function.● Auto power-off function.● Low battery indication.● Calibration performed with supplied test leads.

Product

Wiring Analyzers for Cables, Wire Harnesses, Backplanes

CableEye M2Z, M3Z, M4

-

CAMI Research Inc.

CableEye M2Z, M3Z, M4 - CAMI Research Inc.

With our cable testers and harness testers, find defective or miswired cables instantly before they damage equipment or waste valuable technician time. CableEye® all-in-one test and cable management systems have a unique, patented graphic wiring display to visually pinpoint problems when wiring errors are detected, and offer under a second pass/fail testing for production environments. Quickly locate intermittent connections and identify their position in the cable.

Product

One Wire Communication Board

MS 1727

-

Meltronics Systemtech

MS 1727 - Meltronics Systemtech

- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.

Product

Cable Route Tracing and Identification

-

Megger Group Ltd.

Megger Group Ltd.

Cable pinpointers and fault locators from Megger make the process of cable route tracing and identification quicker and more accurate. These pinpointing systems are portable for everyday fieldwork and provide services from power and telecoms to water, rail and gas utilities. HV and LV buried cables can be traced to a depth of up to 5m.

Product

3 ft Coax Wire with a Coax Pin

GX96411

-

Marvin Test Solutions, Inc.

GX96411 - Marvin Test Solutions, Inc.

One 3 ft Coax Wire with a Coax Pin Crimped on One EndRequires the GX96409 connector housing.

Product

Wire Strippers

-

Omega Engineering, Inc

Omega Engineering, Inc

Thermocouple wire, cable and OMEGACLAD™ wire at strippers. Specialized wire and cables require specialized tools. Make your choice with a range of diameters and gauges.

Product

Industrial Dew-Point Transmitters, Dew-Point Sensors and Trace Moisture Sampling Systems

-

Process Sensing Technologies

Process Sensing Technologies

Our range of dew-point sensors are easy to install and maintain.

Product

Voltage Tester With Wire Stripper

7122A

-

Peaceful Thriving Enterprise Co Ltd

7122A - Peaceful Thriving Enterprise Co Ltd

The product can measure AC voltage 10V to 1000V and DC voltage 7V to 1000V with polarity indication. All testing results will be displayed by LCD. This product can also measure continuity and RCD. Eventually, for the convenience of wire stripping and cutting, this product has combined the function of wire stripper.

Product

Pin-Line™ Collet Socket with Wire Wrap Pins

Series 0503

-

Aries

Series 0503 - Aries

Pin-Line Collet Sockets with Wire Wrap Pins. Features: Rows of socket strips may be mounted on any centers and are end-to-end or side-by-side stackable for .100 [2.54] grid or matrix patterns. Available with wire wrap or solder tail pins. Consult Data Sheet No. 12013 for solder tail pins. Break feature allows strips to be cut to the number of positions desired.

Product

Platinum RTD Sensor - PT100 - 3 Wire 1 meter long

-

Adafruit

Adafruit

For precision temperature sensing, nothing beats a Platinum RTD. Resistance temperature detectors (RTDs) are temperature sensors that contain a resistor that changes resistance value as its temperature changes, basically a kind of thermistor. In this sensor, the resistor is actually a small strip of Platinum with a resistance of 100 ohms at 0C, thus the name PT100. Compared to most NTC/PTC thermistors, the PT type of RTD is much most stable and precise (but also more expensive) PT100's have been used for many years to measure temperature in laboratory and industrial processes, and have developed a reputation for accuracy (better than thermocouples), repeatability, and stability.

Product

Wire Trackers

-

Uni-Trend Group Limited

Uni-Trend Group Limited

Used to locate wires and identify circuits and breakers without having to put unnecessary holes in walls or waste time guessing to find the correct wire in a bundle or run.

Product

Lo-PRO®file Collet Socket with Wire Wrap Pins

Series 503

-

Aries

Series 503 - Aries

LO-PRO file Collet Sockets with Wire Wrap Pins. Features: LO-PRO file Collet Sockets are available with solder tail or wire wrap pins. Consult Data Sheet No. 12011 for solder tail pins. Choose from several sizes and plating options.

Product

Trace Probe

-

Ashling Microsystems Ltd

Ashling Microsystems Ltd

Vitra-XS is Ashling’s Debug & Trace Probe for embedded development with support for multiple target architectures including RISC-V, Arm-Cortex, MIPS (P8700 & I8500) & Synopsys ARC-V & ARC powered systems. Vitra-XS works with Ashling’s RiscFree™ SDK for advanced embedded system debugging, tracing, profiling & analysis.

Product

High Precision Glow Wire Tester

CX-Z17

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-Z17 - Shenzhen Chuangxin Instruments Co., Ltd.

IEC60695-2-1 CX-Z17 High Precision Glow Wire Tester is desinged according to IEC60695-2-1, IEC60695-2-13, UL746A, IEC829, DIN695 and VDE0471 etc. standards.The IEC60695-2-1 CX-Z17 High Precision Glow Wire Tester is suitable for resistance to abnormal heat and fire test on lighting lamps, electronic products and household appliances.

Product

4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers

-

CAMI Research Inc.

CAMI Research Inc.

An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.

Product

Handheld Wiring Analyzer

HT-128+

-

NEXU Technologies, Inc.

HT-128+ - NEXU Technologies, Inc.

Reduce your wire harness assembly and installation difficulties now. The NEXU HT-128+ test platform provides a valuable tool for multi-point wiring continuity analysis. Our versatile, lightweight, handheld unit can serve your wiring test and maintenance needs from harness layout to product field support. The HT-128+ performs testing and troubleshooting, automated ring-out, directed assembly plus other features to resolve wiring issues quickly to achieve increased product availability!

Product

DC Parametric Test System with Curve Trace

DC3

-

Hilevel Technology, Inc.

DC3 - Hilevel Technology, Inc.

The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.

Product

Enameled Wire Portable Pinhole Tester

-

Shanghai Dean Electrical Co., Ltd

Shanghai Dean Electrical Co., Ltd

DZK high and low voltage (portable) pinhole detector is designed and produced in accordance with GB/T4074.5-2008 standard, and can be used by users to monitor the continuous performance of the paint film of the product in real time during production and use. . It takes into account the detection function of the traditional high-voltage paint film continuity tester, and the advantages of being easy to move and replace the use position (the whole machine weight is less than 5KG and can be equipped with lithium batteries), which is convenient for users to detect multiple environments and multiple cables. use.

Product

5 KN Grips For Fine Wire

-

Shimadzu Corp.

Shimadzu Corp.

These grips offer a suitable method for tensile testing soft metal wires, ropes, and strings, all with a diameter of 3 mm (0.12 in) or less. The upper and lower grips include an articulated joint to maintain alignment of the specimen with the testing axis during testing.

Product

3 Wire (Digital) Earth Resistance Tester

4120 ER

-

Standard Electric Works Co., Ltd

4120 ER - Standard Electric Works Co., Ltd

● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Battery test indication.● Calibration performed with supplied test leads.

Product

Compact Measurement System For Steel Wire And Rods With Small Diameters

-

LAP GmbH

LAP GmbH

A glowing hot wire is pulled through the rolling mill at about 120 meters per second during ongoing production. Speed, high temperatures and dirt are special challenges for a high-precision measuring system. Our solution is the Contour Check Wire. It is specially designed for the geometric measurement of wires, rods and rebar and, at 800 Hz, offers the optimum measuring rate for accurate data acquisition. In the uniaxial version, you can check the diameter; in the two- to three-axis version, the ovality can also be determined. The small dimensions and light weight allow a quick and easy integration of the Contour Check Wire into the existing line.

Product

LXI Wired Trigger Bus Adaptors And Accessories

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

We manufacture LXI Wired Trigger Bus adaptors and accessories. These adaptors and accessories are designed to help debug a WTB system or provide conversion of signals to or from the WTB to products that do not support the WTB. LXI approved WTB cable assemblies and terminators are available to interconnect LXI devices that support the LXI Wired Trigger Bus extended function.

Product

Wire Harness Tester

NX Solo

-

Dynalab Test Systems, Inc.

NX Solo - Dynalab Test Systems, Inc.

The Dynalab NX Solo Tester is an economical, feature-rich, stand-alone wire harness tester offering up to 256 test points. The powerful NX Editor software application is used to create unique program files to successfully validate all electrical and electro-mechanical wire harness parameters. This tester is compatible with all Dynalab NX accessories such as printers, scanners, control ports, and much more. The NX Solo Tester supports network communications with the NX Server for efficient file transfers and advanced data collection.