Product

Wire Crimp Pull Tester (Motorized)

WT3-201M

-

Mark-10 Corp.

WT3-201M - Mark-10 Corp.

The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.

Product

3'Harness, 50-Pin Male D-sub Connector on one end, loose wired (numbered) other end

GT97107

-

Marvin Test Solutions, Inc.

GT97107 - Marvin Test Solutions, Inc.

3' harness, 50-pin male D-sub connector on one end, loose wired (numbered) other end.

Product

4-20 mA Loop Powered Two Wire Oxygen Transmitter

OxyTrans

-

Edgetech Instruments

OxyTrans - Edgetech Instruments

The Edgetech Instruments Model OxyTrans is an easy to use, accurate and economical way to measure Oxygen at trace and % levels. A simple display and one point calibration allows for a quick start of the instrument.

Product

Glow Wire Test Apparatus

-

SCR ELEKTRONIKS PVT. LTD.

SCR ELEKTRONIKS PVT. LTD.

GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.

Product

I/O Wiring Cable

PCL Series

-

Advantech Co. Ltd.

PCL Series - Advantech Co. Ltd.

I/O wiring cable sets are designed for easy field wiring capabilities. The PCL-1050 I/O wiring cable series can be used with multiple I/O cards.

Product

Gauge Type T Thermocouple Wire

W-TW-30

-

Physitemp Instruments

W-TW-30 - Physitemp Instruments

Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.

Product

3 Wire (Digital) Earth Resistance Tester

1820 ER

-

Standard Electric Works Co., Ltd

1820 ER - Standard Electric Works Co., Ltd

● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.

Product

Platinum Wire Electrode – 0.1–1.0 Mm Diameters

PEE1

-

PotentioLab

PEE1 - PotentioLab

High-purity platinum wire (99.99%) designed for flame tests, water electrolysis, and general electrochemical research. Featuring excellent conductivity, corrosion resistance, and thermal stability, platinum wire provides a chemically inert support that does not interfere with flame colors or electrochemical reactions. Available in diameters from 0.1 mm to 1.0 mm, with custom lengths and configurations available.

Product

3 Wire (Digital) Earth Resistance Tester

1120 ER

-

Standard Electric Works Co., Ltd

1120 ER - Standard Electric Works Co., Ltd

● Waterproof: IP54● Capable of measuring earth resistance and earth voltage● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test● The test leads are supplied as standard accessories for simplified two-wire measuring system● 0Ω adjustment● Battery operated● Data hold function● Low battery indication

Product

Automatic Video Tracker

ADEPT105

-

Abaco Systems Inc

ADEPT105 - Abaco Systems Inc

Full-featured CompactPCI video tracker detects multiple targets and tracks multiple objects over land, sea and air.

Product

K-Type Thermocouples Wire, Fiberglass (32deg F to 900deg F) 2 m

745690-K002

-

NI

745690-K002 - NI

K-Type Thermocouple, 32°F to 900°F Temperature Sensor - The K-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the K-Type Thermocouple and acquire synchronized temperature data in units of degrees. The K-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.

Product

Straight Wire Porbe Pins

Buckling Beam

-

Prospect Products Inc.

Buckling Beam - Prospect Products Inc.

Straight wire probe pins are a proven solution for various electronics production test environments.

Product

Fault Finder for Electrical Wiring Open / Short Circuit

FF310

-

General Technologies Corp.

FF310 - General Technologies Corp.

42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions.

Product

Non-Contact Voltage Tester With Wire Stripper

5227

-

Peaceful Thriving Enterprise Co Ltd

5227 - Peaceful Thriving Enterprise Co Ltd

This product combines most required tools for an electrician to do the wiring job within the building, which includes screwdriver, non-contact voltage detector, illumination and wire stripper for most type wires.

Product

Platinum RTD Sensor - PT100 - 3 Wire 1 meter long

-

Adafruit

Adafruit

For precision temperature sensing, nothing beats a Platinum RTD. Resistance temperature detectors (RTDs) are temperature sensors that contain a resistor that changes resistance value as its temperature changes, basically a kind of thermistor. In this sensor, the resistor is actually a small strip of Platinum with a resistance of 100 ohms at 0C, thus the name PT100. Compared to most NTC/PTC thermistors, the PT type of RTD is much most stable and precise (but also more expensive) PT100's have been used for many years to measure temperature in laboratory and industrial processes, and have developed a reputation for accuracy (better than thermocouples), repeatability, and stability.

Product

Datapaq Kiln Tracker System

-

Fluke Process Instruments

Fluke Process Instruments

Datapaq Kiln Tracker Systems from Fluke Process Instruments are designed to provide thermal profiles for ceramic-firing applications in roller hearth kilns, hydro kilns, clay block kilns and tunnel kilns.

Product

Laser Trackers

Radian Series

-

Automated Precision Inc.

Radian Series - Automated Precision Inc.

The smallest, lightest, most accurate laser measurement tool. API’s compact and rigid UNIBODY tracker design allows for shaft mounted motors, encoders and laser. The UNIBODY shaft mounted laser innovation minimizes Abbe offset errors, while also housing laser source, optics, camera and major head electronics in the center of the tracker body.

Product

Laser Tracker Tools And Accessories

-

MetrologyWorks Inc.

MetrologyWorks Inc.

MetrologyWorks provides a full line of Laser Tracker Accessories as well as Laser Tracker Tooling and Adapters. This includes Drift Nests, Permanent Monuments, Pin Nests, Edge Nests, Hidden Point Bars. If you need something custom we can provide custom Laser Tracker Tooling as well.

Product

4 Wire Earth Resistance & Resistivity Tester

4235 ER

-

Standard Electric Works Co., Ltd

4235 ER - Standard Electric Works Co., Ltd

● Microprocessor-controlled.● Earth resistivity (ρ) test.● Earth testing at 20Ω, 200Ω, 2kΩ.● Earth voltage measuring : 0-300V AC.● Automatic C spike check.● Automatic P spike check.● 2-Wire test, 3-Wire test, 4-Wire test.● LCM display.● Auto ranging.● Auto power OFF.● Data hold.● 200 measurement results can be saved in the memory and recalled on the display.● Interval between auxiliary earth spikes is 1.0~50.0m.

Product

3 Wire (Analogue) Earth Resistance Tester

1105 ER

-

Standard Electric Works Co., Ltd

1105 ER - Standard Electric Works Co., Ltd

● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.

Product

DB25 DIN-Rail Wiring Board

ADAM-3925

-

Advantech Co. Ltd.

ADAM-3925 - Advantech Co. Ltd.

Low cost universal DIN-rail mounting screw terminal module for PC-LabCard products with DB25 connectorScrew-clamp terminal blocks allow easy and reliable connectionsCase dimensions (W x L x H): 77.5 x 56.3 x 51 mm (3.1" x 2.2" x 2.0")To Be Used With PCI-1757UP, PCL-833

Product

Wire Crimp Testers

-

IMADA, Incorporated

IMADA, Incorporated

Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.

Product

Wire Tracer

LKZ-700

-

Sonel S.A.

LKZ-700 - Sonel S.A.

Wire tracer LKZ-700 is designed for detecting of cables and conductors in various environments (concrete, brick, wood, ground) being under voltege, without the need to disconnect any devices from tested network, as well as in non-voltage environments.